How do you remove the curtain screen and press it?

The curtain is removed in the way of pressing up:1. If you want to remove the window screen, it will generally be fixed in the track, so you can lift the screen frame with one hand to expose the gap below.

2. Next, move the window frame to the track, after crossing the first track, lift the other end, slowly move it outward, when the whole lower edge is detached, and then remove the upper end, the whole screen window can be taken off directly.

3. After cleaning, it will be installed back, and the installation is very simple. Snap one end into the track first, top up with your right hand, and then snap the top end into the track.

In fact, installing window screens is not as difficult as imagined, as long as you use the appropriate tools, a few small steps can be completed. If there is an old screen, remove the old screen first, you don't need to replace the entire screen, you only need to replace the screen, you can find a handful of words, and lift the strip in the frame of the old screen window to pull the strip out, so that the screen is disassembled. Prepare new screens and beads, as well as a tool to install the beads into the screens, a roller tool, and a slot.

Cut both sides of the newly purchased window screen with the inner frame of the screen frame, and keep the part of the bead that needs to be fixed. Prepare the bead and place the bead along the recess of the inner frame of the screen and above the screen.

Then use the roller tool to press the bead in. Some corners can be pressed in with the help of a single word. When fixing the third and fourth sides, it is necessary to tighten the curtain and press the strip in, and press the excess strip in, and press the tail in with a slot, and finally cut the excess screen with a knife.

There are 3 steps to remove the sliding screen.

1. First of all, push and pull the window screen to the middle of the window to ensure that there is a certain amount of activity on both sides.

2. Face the window and hold the middle and lower part of the screen frame with both hands. If the sliding window is too high, you will need to step on a stool, but the window should be closed to prevent accidents.

3. Use both hands upward at the same time, and after the screen is moved up, maintain the upward strength and pull inward, so that the lower part of the screen is off the track and can be easily removed.

Generally, the screen window of the casement window can be dismantled according to this step:

1. Prepare two one-word change cones.

2. Open the window sash, look at the two corners under the screen frame, and use the cone to take the window as the fulcrum and tilt it upward.

3. The screen window moves up as a whole, and after the lower edge and the window leave the gap, put the taper into the gap, and grab both sides with both hands, then the screen window will be removed as a whole.

This casement window embedded in the fixed screen window, just up and down stuck on the window frame, when dismantled, it is also up first, the lower part can be removed after detachment, when installing, it is also installed first, after putting it on, press it down, even if it is tightened.

Here's how to remove the curtain:

If you want to remove the screen, you can grasp both sides of the screen with your hands, lift it up vigorously until you reach the top of the circle, then remove the lower end of the screen from the card slot, and the screen will be removed.

Cleaning method of window screen: first clean all the ash on the surface, and then rinse the orange liquid under the faucet. Prepare a large basin, put laundry detergent in it, as well as baking soda and white vinegar solution, soak for about 15 minutes, prepare a brush to scrub the screen, baking soda and white vinegar solution is very strong cleaning ability, can effectively dissolve stains, you will find that the stains will gradually fall off.

Then we put it under the faucet, clean the foam, and dry it in a cool place.

Precautions for installing window screens

1. The first thing to pay attention to when installing the screen window is the material problem, which must be complete, so as not to affect the installation progress. At the same time, it is also necessary to pay attention to the size of the window frame, which must be used to bury the imitation purchase screen window according to this size, so as to avoid the phenomenon of inconsistency in size.

2. There is also the position of placement, which is also the place that needs to be paid attention to when installing. The box must be vertical, and the two air ducts must be installed in the middle. At the same time, it should also be noted that the spacing on both sides of the window frame must be the same, and the left and right sides should be symmetrical.

In addition, the bottom of its pad cannot be placed directly, it should be placed about 5 cm below the border, and then fixed with a clamp when it is all completed.

3. After the screen is installed, you need to clean the window frame first, tear off all the adhesive protective film, and finally install a rope on the triangle under it to use.