How can the sink stopper be removed

If you want to remove the washbasin stopper, you can try the following two methods:

1. If you want to disassemble the flip plug of the washbasin, it is very simple, you can prepare a pliers, and then clamp the flip plug of the washbasin. After that, pull it up hard, you need to pay attention to balance when you pull it, and you must not hurt yourself, and then as long as you pull it out, you can effectively loosen the flip plug;

2. But there may be times when it is stuck, there is no way to pull it out, we can observe whether there are some sundries around, such as hair or other small wooden sticks clamped, take things out, and then flip them over, add lubricant, let the lid lubricate, and then use pliers to clamp the lid and take it out.

Method 1: Remove the U-shaped pipe under the washbasin, then take a stick from below and poke it at the basin plug, poke the basin plug out, and then connect the U-shaped pipe.

Method. 2. Find the place where the gap between the pot plug is slightly larger, and then use a screwdriver.

Or a hard object with a relatively small contact surface can reach in and pry the basin plug up.

Method. 3. Melt fertilizer soap with warm water to make soapy water, then pour the soapy water on the washbasin plug, wait for a while, and then try to press the spring plug a few more times.

Tips for cleaning the sink:

1. In fact, long-term use of the sink will produce a large amount of scale, and the negative scale on the sink will make the sink dull.

2. First of all, we can use professional dish soap.

Carry out right side cleaning, pay attention to the use of a dry cloth to wipe during the cleaning process, and do not use steel wool to wipe, to avoid wiping off the glaze of the sink, so as to cause the sink's aesthetics to be insufficient.

3. You can also use soap to wrap a thin layer of rags, first of all, the rags can not wring out the water, we wash the rags wrapped in soap, so as to avoid scale in the sink.

This type of plug has a shaft, and the plug can rotate around the shaft.

You don't press the middle of the stopper, you press the edge of the stopper, and the plug can turn to the right angle and the water can flow down.

This is pressed to the side, using your fingers to press down while pestle.

There is a turnbuckle that holds the plug head in place, which is unscrewed clockwise with a pipe wrench.

Under the sink, there is a special turnbuckle to fix the plug head, unscrew it clockwise with a pipe wrench, if it is plastic, pay attention to the strength, and after rotating and removing it, you can lift it all out.

The specific procedure for replacement is as follows.

1. When removing the old sewer, the sewer nut needs to be loosened and the sewer pipe and sewer should be separated. Then use a wrench to loosen the fixing nut of the drainer and remove it, and then lift the drainer up and take it out. If there is a glass glue seal between the drainer and the basin, you can scrape off the sealant with a knife and then take the drainer out.

2. You can wipe the installation position of the sink drainer with a rag, etc., and then measure the diameter of the drain with a ruler, and buy a new drainer according to this size. After the sewer is purchased, it is necessary to carefully check whether there is a quality problem with the sewer. Before formal installation, the sewer parts can be disassembled, such as unscrewing the sewer nut and removing the two sealants.

3. When installing the sewer, the raw material belt can be wrapped around the sewer, and the raw material belt generally needs to be wound more than ten times. Then put the upper spacer over the drainer and place the drainer on the drain. During installation, it can be sealed with glass glue between the drainer and the ceramic basin.

Then place the lower spacer under the drainer and tighten the retaining nut. Once the drainer is installed, secure the drain pipe to the drainer. Finally, turn on the faucet and check whether the drain can store water normally and whether there are any problems such as water leakage.

This question fully mobilizes the imagination of the answerer, first of all, you have to understand the location of your wash basin and the fixing method, master these basic information, and then you can specifically study how to remove it?

A1Pull the drawer out until it can't be pulled, and then you look carefully at the plastic strips in the rails on each side of the drawer, and you push the plastic roots in the rails up and down with both hands. 2.

Then pull the drawer again! (Do not let go of the two hands on the plastic strip when pulling). If you can't pull it out, you can push it up on the other side and press down on the other side!

Question: Remove the drawer from the sink.

A1Pull the drawer out until it can't be pulled, and then you look carefully at the plastic strips in the rails on each side of the drawer, and you push the plastic roots in the rails up and down with both hands. 2.

Then pull the drawer again! (Do not let go of the two hands on the plastic strip when pulling). If you can't pull it out, you can push it up on the other side and press down on the other side!

That's it.

Dear, you can follow me, if you have any questions you don't understand, you can consult me, and I will patiently answer for you. I wish you a happy life, and remember to give a thumbs up! Hee hee ( Trouble to give a thumbs up.) 

Question: What if there are no plastic strips?

Because of this kind of track, it has plastic strips.

This plastic strip is its switch.

If the stopper of the sink is rotated, it can be removed by using a lever with a stick.

Just pry it out. If you want to press the plug, you need to find the turnbuckle that holds the plug under the basin, and unscrew the turnbuckle to remove the stopper.

There are usually two types of sink plugs, one is rotary, and this plug is very easy to remove.

We only need to prepare a small stick that is strong enough, turn the plug up first, then put one end of the stick under the plug, and hammer the other side of it, so that it can be easily pried out by the lever principle.

If it is a press plug to be removed, it is more complicated, usually there is a turnbuckle under the basin of the sink that uses this plug, the function of this turnbuckle is to fix the race head, we only need to unscrew it to remove the stopper.

The steps to cut out the sink plug are as follows:

Tools: blades, shower gel.

1. First of all, squeeze two drops of shower gel out of the sink stopper.

2. Then use your hands to evenly apply the shower gel to the entire edge of the stopper.

3. Then prepare the blades and other tools.

4. Then slowly the tool along the seam of the edge of the plug.

5. The plug is warped.

What should I do if the plug in the bathroom basin won't open? Hello dear, hello there are two ways to try it:; First, you can use a small driver to find a position with a little gap, and the disadvantage is slowly upturned, and it can be opened slowly.

Second, there is a screwdriver and a hammer at home. With a flathead screwdriver, the bit is placed on the edge that can be rotated, and the tail of the screwdriver can be opened by hitting the tail with a hammer. Hope it helps.

First of all, the water in the pool is discharged, and then the main water valve is closed, and under the sink, there is a special turnbuckle to fix the plug head, clockwise with a pipe wrench.

Unscrew it, if it is plastic, pay attention to the strength, and after rotating and removing it, the whole lifting will come out. If you want to install it, pay attention to the pipe fittings that can be unloaded at the place of the backwater bend, and add a waterstop after unloading and cleaning.

Wrap and re-tighten it. <

Plug disassembly method of washbasin: first put the water in the pool, then close the main water valve, under the sink, there is a special turnbuckle to fix the plug head, unscrew it clockwise with a pipe wrench, if it is plastic, pay attention to the strength, rotate and remove the whole lift to come out. If you want to press it, pay attention to the pipe fittings that can be unloaded at the place of the anti-water bend, and after unloading and cleaning, add a waterstop to wrap and re-tighten it.

<> generally there will be a special button to fix the plug below the sink, lift the button and rotate the plug a few times to take it out, if there is no buckle to fix the stopper, you can also use a tool to warp the stopper, use the lever principle to stick or wire into the plug and then warp it in the opposite direction, the plug can be cut out, and finally the pipe under the pool can be unloaded, after unloading, the plug is pushed out with a tool from below, and it can be cleaned. If the plug is flipped, you can use a screwdriver to jack the plug up and hit it with a hammer a few times to remove it.