-
The toilet has been used for a long time, there will always be problems, small problems can be endured once or twice, and often problems are not good, which involves the process of replacing the toilet and installation.
1. Replacement. Replacing the toilet is undoubtedly about replacing the old toilet, and the specific steps are as follows:
First of all, the main water valve should be turned off, and the triangle valve in the water tank should also be closed, as for the water in the water tank, it should be discharged first, and the remaining part should be scooped clean with utensils; The next step is the removal of the toilet pipes and their fittings. As for the glass glue around the toilet bowl should also be removed, otherwise the base can not be removed, in the process of shoveling glass glue, be careful not to scratch your hands, as far as possible to minimize scratches on the tiles. After removing the glass glue, the next step is to use a screwdriver to remove the screws on both sides of the toilet, and the screws can be removed to directly lift the toilet base and remove it.
2. Installation. After the replacement is completed and the toilet is removed, you can clean the toilet around the toilet before installing the new toilet and keep it clean, after all, there is garbage in the process of replacement, and there will be stains after long-term use, all of which need to be cleaned before installation.
As for the part of the floor tiles, it is not necessary to knock them off, usually the installation of the toilet is really on top of the floor tiles; Of course, if the toilet was installed first and then tiled, then the toilet should not be knocked out if it is under the floor tiles; It can be flattened with a professional cutting machine, and the low-lying areas can be filled with cement, and the damaged tiles can be replaced in the process.
In the process of formally installing the toilet, the wax ring must be put on first, the toilet is placed flat in alignment with the drain, and the fixing screws must be tightened; Immediately after installing the hose and opening the triangle valve to water the water, the glass glue around the toilet base must be indispensable. Once all this is over, wait a day before it can be used normally.
That's it for the replacement and installation of the toilet, if your toilet is also on the verge of replacement, then you can learn from it! Hope it will be helpful for your future renovation.
-
If the toilet at home is broken and ready to be replaced, it is recommended that it is best to use neutral glass glue to fix the toilet, because neutral glue does not have a pungent sour smell and is stronger than acidic glue.
-
Use neutral glass glue because neutral glue does not have a pungent sour taste and is stronger than acidic glue.
After being glued with glass glue, it can be used after installation as long as no external force is applied.
-
The fixed toilet should use special glass glue, and it is necessary to choose the best one, otherwise it will be easy to become black and moldy after a long time, and the glass glue will be used after a while.
-
1. When working, you need to wear protective work gloves, first remove the water tank cover and place it in a place where there is no water, and remove the water tank cover first to avoid hitting yourself. Close the water valve. Use a sponge or towel to dry the water in the tank that has not yet run away.
2. Clean the water in the water tank and toilet. The bucket can be long pressed to flush the flush button, and the toilet can be scooped out with an old towel or small box. If the water tank is connected to the toilet seat, the bolts may not be removed, so remove the water tank from the toilet seat.
3. Generally, there will be a circle of glue under the toilet, which should be cleaned with a wallpaper knife. Using a single-handle saw, if the toilet at home is glued to the floor with gap filler, you can use a tool knife to cut the sealant open, gently shake the toilet to loosen the toilet from the sticky sealant, and then lift the toilet.
-
I don't know, it's too polluting the environment.
-
Throw it away, what can you do if you keep it?
-
Be sure to look at the pit distance, otherwise there will be a big problem when you buy it back and install it. Generally 300 400mm. It's best to choose the siphon type, that is, the horizontal one.
Then see if the toilet meets the water-saving standard. The water absorption rate is not less than 100%, and such a water absorption rate is in line with the standard. Of course, the lower this indicator, the better. It proves that this toilet bowl has reached full vitrification.
Such a product will be odor-resistant and water-impermeable. In short, it is more assured, look at the accessories, the quality of the water tank inside is also critical. You can see if the weight of the toilet is large, it is better if it is large, and it should be molded in one piece, so that it will not leak, and you can let him try it for you on the spot.
-
1. The sewage pit spacing of the old toilet (most of the new ones are 300mm, 400mm, and the old ones are 200mm and 250mm), if the pit spacing is 200mm, you can't install the pit spacing of 300mm (it is best to buy the same pit spacing as the old toilet). 2. The height of the inlet valve, see if the new toilet tank is blocked. 3. It is best to change some water-saving toilets (with two gears).
-
First of all, pay attention to whether your toilet is drained or side drained If you buy the wrong one, if it is drainage, you should measure the distance from the center of the drain to the back wall (pay attention to the amount of tiles,) and then buy the toilet according to the size, and then buy the toilet according to the size. If the size is too large, the drain of the toilet does not match the drain of the floor drain, and it will not work.
-
If you change the toilet, you only need to re-waterproof it around the toilet drain pipe, because when the old toilet is removed, the original waterproof layer is easy to cause damage. During the insurance period, it is better to do waterproof again.
-
The seat of the toilet can be replaced, and the method of replacing the toilet seat is as follows:
1. The toilet seat is fixed by two bolts, one on the left and one on the right, the red circle in the picture, and the screws below, both of which are bolts and nuts made of plastic. It can be removed by holding the bolt on top with one hand and loosening the nut below with the other.
2. Go online or in a store to buy a new toilet seat, and take a picture of the owner to determine whether the toilet is O-shaped, U-shaped, or V-shaped.
3. Check the accessories of the newly bought toilet seat, first fix the bolt screws and buckles to the bracket, and the left and right buckles can slide to facilitate plugging into the bolt holes.
4. Plug into the hole of the screw, or fix it directly with a screwdriver.
-
Summary. Hello, glad to answer for you. Kiss, the toilet seat is broken and needs to be replaced; 1. The toilet lid can be replaced when it is broken.
The owner only needs to buy a similar new toilet seat according to the shape, size, and size of the original toilet seat and replace it. There are many styles and sizes of toilet seats on the market, in order to avoid buying an unsuitable toilet seat that cannot be installed, then you must first measure the size and shape of your toilet seat before buying a new toilet seat.
The toilet seat is broken and needs to be replaced.
Hello, glad to answer for you. Kiss, the toilet seat is broken and needs to be replaced; 1. The toilet lid can be replaced when it is broken. The owner only needs to buy a new toilet seat that looks like a big bend and replace it according to the shape of the original toilet seat, the size and size of the plum.
There are many styles and sizes of toilet seats on the market, in order to avoid buying an unsuitable toilet seat and not being able to install it, then you must first measure the size and shape of your own toilet seat, and then buy a new toilet seat.
2. Before replacing the new toilet seat, we should first remove the broken toilet seat. We can find the position of the screws that hold the toilet seat on both sides of the lower back of the toilet, and then we need to unscrew the screws so that the broken toilet seat can be removed, and the remaining screws and screw slots should also be removed. 3. Before replacing the new toilet seat, we should also unpack the new toilet seat, take out the new toilet seat and its related accessories for inspection, and see if there is any missing or damaged.
In addition, you should also place the new toilet lid on the toilet bowl to see if the size and shape are appropriate, and after confirming that there are no problems, you can start installing the new toilet seat. The owner can replace it by himself, and if the foundation fails, then he can ask a professional maintenance person to come to help replace it.
-
1. The homeowner can check the toilet for damage. Before installing the toilet, the sewage pipeline should be comprehensively inspected to see if there is mud, sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation position is horizontal. Unpack the toilet, remove it, and attach the hose to the back of the toilet.
The installation accessories of the toilet are mainly angle valves and hoses, which can be purchased by yourself or negotiated with the merchant).
2. Take a ruler to measure the distance between the wall and the ground outlet. Flip the toilet, center it on the toilet drain, and draw a cross center line, which should extend to the bottom of the toilet around the feet. The distance between the wall of the homeowner's bathroom and the sewage outlet is 400mm, which is exactly the 400 hole spacing of the toilet.
If the distance is 300mm after measurement, you can choose to use 300 hole spacing on the toilet. In special cases, a shifter is also required. In most cases, houses are now designed with a distance of 400mm.
3. Wipe the ground around the sewage outlet clean to facilitate the installation of the toilet. The homeowner can work with the installer to close the water valve in the bathroom.
4. Install angle valves. After that, place the toilet bowl on top of the drain outlet, and after comparison, use a pencil to draw a line along the edge of the toilet bowl to facilitate installation. Then, place the toilet aside.
Determine the installation position of the foot screws at the bottom of the toilet, make the installation holes with an impact drill, and embed the plastic rubber sleeve of the expansion screws.
5. Along the pencil line, mark the glass glue. (This installation method is currently the most used method, simple, sturdy, beautiful.) It is much more advanced than the previous method of building a cement platform. )
6. Carefully place the toilet bowl on the glass glue and compare it with the ground sewage outlet. After attaching it, the overflowing glass glue from the toilet bowl is tightly packed and kept beautiful. Install a special sealing ring on the toilet drain outlet, or put a circle of glass glue (putty) or cement mortar around the sewage pipe, and the ratio of cement to sand is 1:
3。The toilet should be installed at the front and back and left and right levels.
7. Tighten the angle valve and hose interface with a wrench. Install or debug the tank fittings. Check the water pipes first, drain the water for 3-5 minutes to rinse the pipes to ensure the cleanliness of the water pipes; Then install the angle valve and the connecting hose, then connect the hose with the installed water tank accessories inlet valve and press the water source, check whether the water inlet and sealing of the inlet valve are normal, check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and check whether there is leakage and install the inlet valve filtration device.
8. Open the tap water valve, put on the water, and let the homeowner check the water tank. If any abnormalities are found during the debugging process, please refer to the "Common Faults and Handling Methods of Toilet and Water Tank Accessories" for inspection and handling.
9. After the toilet is installed, it should wait until the glass glue (putty) or cement mortar is solidified before it can be used with water, and the time is generally 24 hours.
10. The homeowner tests the water, and the siphon jets the water. Punchy, smooth, whirlpool launch. You can see that the installation of the toilet is complete.
-
Generally, everyone will install a toilet in the bathroom, and everyone usually uses the bathroom. Therefore, it is very important to choose a good material toilet, so that it can be convenient for everyone to use, and everything at home is generally used for a long time, and if it is broken, Huaicha is like a toilet, and the toilet needs to be replaced after a long time. Otherwise, it will affect everyone's use.
And now there are many toilets made of materials on the market, but if you want to replace the toilet, you have to find my common sense to replace the toilet, so I will introduce it to you.
Toilet replacement method — The method process of replacing the toilet bowl
1.To change the toilet seat, you must first find the screw cap, then remove it with a live hand, and then replace it with a new one. Regardless of the location of the general screw cap, some are in the bright and some are in the dark, everyone should look carefully.
The screw cap in the dark, on the side of the water tank in the toilet, is generally set at the edge of the water tank of the toilet, and the lid is opened. If you put your hand in it and touch it upwards and in the direction of the tank, you should be able to touch it, but you can't see it.
2.To install the toilet seat, you need to remove the fixing bolts at the back of the toilet, remove the previous toilet cover, and then replace the new toilet seat with a fixed screw cap. At present, most toilet seats are large and small, as long as the screws at both ends of the toilet are done.
However, the size of the toilet bowl must be measured before changing the toilet lid, and the width and length of the screw cap from the toilet lid also need to be determined. So as not to buy products that do not fit.
3.If you still find it difficult to use the above two methods, we can find a professional to change. As long as it is a product provided by their manufacturer, they will generally have free after-sales service.
What to pay attention to when replacing the toilet
1.Check and adjust the floor level: After buying a toilet with the same wall spacing size and sealing cushion, you can start the installation.
Before the installation of the toilet, a comprehensive inspection of the sewage pipe should be carried out to see whether there is mud, sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation position is horizontal.
2.Check whether there is leakage after debugging and installing the water tank accessories: check the water pipe first, and rinse the pipe for 3-5 minutes to ensure the cleanliness of the water pipe; Then install the angle valve and the connecting hose, then connect the hose with the installed water tank fitting inlet valve and connect the water source, and check whether the water inlet and sealing of the inlet valve are normal.
Here are some ways to replace the toilet, I believe you know how to replace the toilet after reading it! Well, the toilet is necessary to equip the bathroom, and everyone usually uses the bathroom, so the choice of blind children is very critical, the quality of the toilet is related to whether everyone can use it normally, and often make the boy stupid for a long time to need to replace, and we may not know much about the common sense of these replacements before, so I don't know how to replace the toilet after buying it back, if you have purchased a toilet and need to replace it, you can replace it according to a method introduced to you, Hope it helps.
You can get it for free
If you change the hall, change to a gigabit 5G router.
1. If you are using a vivo mobile phone, it is recommended to bring the mobile phone to the vivo customer service center for maintenance, vivo customer service center address: enter the vivo official website vivo**app--my--after-sales outlets--select the province and city to inquire about the service center address; >>>More
Guilin's landscape is the best in the world, Guilin is a slow life city! Shops in the city, shops open to do business usually late, the nightlife is more colorful, the air in the city is very fresh, the forest covers a wide area, there are mountains and rivers in the city, there are many osmanthus trees, every time the flowers bloom, the whole city exudes a faint fragrance of osmanthus, the essence of Guilin tourism is the Li River to Yangshuo, Guilin mountains and rivers are beautiful, to Yangshuo to live for a few nights, the whole person is happy! Because Guilin is suitable for "livable", choose Guilin!
The traditional burial rites in Zaozhuang area are more complex and are also an important part of funeral customs. The ancients paid attention to "entering the soil for peace", and the many Han portrait stones and burial vessels unearthed in Zaozhuang can illustrate the longevity of this culture. >>>More
Generally speaking, changing the roof of the car is to change the roof cloth, and the ** of the car roof cloth material is about 100 to 300 yuan. >>>More