I m going to change a Xiaomi router, but there are two routers at home, so it s good to replace that

If you change the hall, change to a gigabit 5G router.

It is recommended to change the hall.

Reason: As the main router of the optical modem, and the bedroom as a sub-router, it will be limited by the main router.

1.Now home broadband is basically 100M, if it is greater than 100M, your router interface rate is only 100M, so that it can only play a maximum of 100M Internet speed.

Principle 1: If the home broadband is greater than 100M, the router interface rate must be dual Gigabit.

2.Wireless wifi rate = 150m * number of frequency antennas) + 433m * number of 5G frequency antennas).

Frequency Mobile phones, Bluetooth, mice, etc. all belong to this frequency band, which is prone to signal interference.

5G frequency (transmission standard: fast speed, but weak ability to penetrate walls.

Principle 2: Try to choose a dual-band router, and the transmission rate should be accurate.

3.Penetration capacity = wireless signal transmission power (no more than 100 mW according to national regulations) + antenna gain.

The antenna gain can only be gained in the horizontal direction, and the more gain, the more dead angles of the signal, and there is no real through-the-wall routing at all.

Principle 3: If the home is large, install a wireless signal extender for signal expansion.

4.The speed of the internet is determined by the router hardware (CPU, memory, firmware).

Principle 4: The hardware level is linked to the budget, the higher the better.

Principle 5: Select features on demand.

No. Just change the router wireless password and sdid (the wifi name is the same as the original).

If the Xiaomi router changes places, you can reset it by resetting the router.

Here's how:

1. Press the "reset" hole on the back of the router to reset the Mi router.

2. Open the webpage and enter.

3. Enter the "Administrator Secret ZD Code" to enter the router settings interface.

4. Select "Internet Access" in the menu bar of "Built-in Routing Settings" on the left, select "Internet Access Mode" as "Broadband Dial-up Online" in "Basic Settings", and then enter your "Broadband Account" and "Broadband Password".

5. In "Advanced Settings", set the "Dial Mode" to "Auto Select Dial Mode", select "Connection Mode" and select "Auto Connect, connect when the phone is turned on and disconnected", and finally click "Save" in the lower right corner.

6. Go back to "Routing Settings" and enter "Wireless Settings". Select "Wireless Settings" as shown in the figure, fill in the "Wireless Name" and "Wireless Password" you want to set as required, set "Wireless Channel" and "Frequency Band Bandwidth" to "Automatic", and then click "Save".

7. If the router supports "5G wireless settings", you can also set it up like the previous step, and then click "Save".

I don't need to change it, just change the router wireless password and sdid (the wifi name is the same as the original).

You need to reset the wifi connected to this route.

How good it is for you to change to electric cats. Purely wireless, it is difficult for routers to do bridging. The two routers are connected by wire, and the cable must be run and the network management should be changed.

Is there a wired connection between the living room and the room?,Wired direct connection Connect Xiaomi under the bedroom route,Just set it up。

Plug in a network cable from the LAN port of the bedroom router, plug in the LAN port of the Mi router at the other end, connect the computer to the Mi router and set DHCP off.

If you want to add a Xiaomi router in the living room, the way is, pull a network cable from the LAN port of the router in the bedroom and connect it to the WAN port of the Xiaomi router in the living room.

As shown below:

If your living room has a network panel, and the cable of this network panel is connected to your bedroom router; If the bedroom router is used as the primary router, the Mi router can be used as the next-level router.

Check if your bedroom router has a bridging function, Xiaomi routers support bridging. Both routers can be bridged to each other, and they can access the Internet.

1.Ask in advance if the Xiaomi router has the function of universal relay.

2.If there is a universal relay function, it will be simple, directly power on the router in the living room, and then log in to the background of the Xiaomi router on the mobile phone, and enter the account password (the initial password is on the router).

3.Set the Wi-Fi function (including Wi-Fi name, encryption method, and password) and save it.

4.Finally, find the universal relay, select the router wifi in your bedroom in the universal relay, then fill in the password, and save it.

Do you want to add a new router as a wifi extension?

Add another network cable to the router plugged into the optical fiber, and connect the network cable to the LAN interface of the Xiaomi router.

Go to the management interface of the Mi router to set it up.

There are two methods: 1. Wired connection Wiring through the LAN port of the bedroom router to the WAN port of the router of the living room and then setting up wifi

2. Wireless connection: Mi router first boots up, enters the background, finds the wireless relay and connects to the router in the bedroom, and then sets up wifi

1. If there is a network cable interface in the living room, and the network is connected (meaning that it can be used when plugged in), then you can plug in the router directly.

2. If there is no network cable interface in the living room, you want to amplify the router signal in the bedroom to the living room through the router;

Common settings--- Internet settings--- switching between working modes (change to relay mode) -- select the wireless relay working mode (if you have to choose) -- select the signal of your main router (bedroom wifi) from the scan results (password must be known) -- restart.

As the main router in the bedroom, under normal circumstances, the Internet is already set up, and the Internet can be accessed with laptop wireless access or mobile phone wifi access. Then do the next thing:

1. Log in to the living room router, connect the bedroom router with a computer, enter the account password after opening, find the LAN port IP, wireless name and other information, and turn on WDS, 2. Connect the living room router with the computer again, enter the same address according to the back of the router, not necessarily this address) Ensure that the LAN port, wireless name and bedroom router do not conflict, and the wireless channel should be consistent with the bedroom router settings.

3. Enter the wireless signal to be bridged, that is, enter the SSID number of the bedroom. Enter the MAC address of the LAN port of the bedroom. The encryption method must be the same.

3. If DHCP is enabled, the gateway in the living room writes the LAN port IP address of the bedroom, and it can be restarted after restarting.

The overall solution is route-link routing;

Prepare a long enough double crystal head network cable, and the quality should be as good as possible;

Connect from the bedroom router to a port other than the WAN port;

The other end is connected to the routing WAN port in the living room;

The premise is to ensure that the bedroom router can access the Internet;

Start the living room route,Initialize the route first,That is, the kind that doesn't set a password in the open state,Then open the notebook,Find the information connection that the wireless signal is the Xiaomi router;

Open the browser to enter, it is the one given on the sticker of the routing base, different manufacturers give it, you enter according to others; Once inside, it's good to set up the same route as you would in the bedroom.

You can add as much as you want, and the route can be set according to the Internet access method on the network cable you are connected to.

1. How to set up the main router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router and connect the computer network card at the other end, and turn on the power supply of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access account and password.

5. Save and continue to set the wireless key, (it is recommended to use a combination of numbers and English for the password, and it is best to use the @ symbol in the middle, so as to prevent others from rubbing the net).

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

Second, the setting method of the secondary router:

1. Do not connect the secondary router to the main router first.

2. One end of the network cable is connected to any LAN port of the router, and the other end is connected to the computer.

3. Change the LAN port IP of the login interface through the computer browser to avoid conflicts with the IP segment of the main router;

4. WAN port Internet access mode selection: dynamic IP connection, enable DHCP server.

5. Set the account and key wirelessly, save and log out.

6. Connect a network cable from any LAN port of the main router to the WAN port of the secondary wireless router, and the computer can access the Internet at this time.

Set Level 2 Routing Method

1. How to connect two routers.

1. There is a cat (modem): cat (modem) - router 1wan port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

2. No modem: network cable --- router 1WAN port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

Second, the setting method.

Before setting, disconnect the WAN port cable of the second router and plug it in after the setting is complete.

1. Set the IP segment of the second router.

After restarting the router, the address to enter the router is.

2. Set up a second router to access the Internet.

Check the IP details of the computer connected to the first router. (win+r--input, cmd--input:ipconfig all [remember: ip, mask, gateway, dns]).

Set it on the second router, and select Static IP in the Setup Wizard. Enter the IP that the 1st router does not use, and the others: mask, gateway, DNS settings are the same.

Restart your router once it's set up.

3. After restarting the router, the setting is completed, and the line of the 2WAN port of the router is reconnected to make the router 2 network normal.

Hello. Trunks can be used.

Xiaomi router mini, one-click relay is really simple.

Dear users, hello:

1. Enter the router address, connect the wireless router, and enter the address you see on the router in the browser, which is generally .

2. Enter the corresponding password, and after entering, you will see that you have entered the corresponding account and password.

3. Select the setting wizard, and then enter the operation interface, you will see a setting wizard on the left, and you will enter it (generally it will pop up automatically).

4. Enter the Internet mode setting and set the interface of the wizard.

5. Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

I chose PPPoE because I dialed.

6. Enter the password, choose PPPOE dial-up Internet access to fill in the Internet account and password, this should be understood by everyone, there will be an account number to open broadband, fill in it OK.

7. Set the password of the router, and then enter the wireless settings after the next step, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill it in casually, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

8. Click Done, the router will automatically restart, so be patient. The interface that appears after success.

9. How to connect the mobile phone to wifi is simpler, when the router is set up, click the menu key of the mobile phone, and then enter the mobile phone settings, the first item is wifi, and then set it to on, click to enter the wifi list, and select the wireless network name set in the router before. Enter the password you set earlier to connect.