How to quickly remove the film from the suit door

1. Apply some wind oil essence or other oily liquid objects on the upturned edge, apply a little and peel off a little, and then peel off again, so that the film on the suit door can be removed by repeating it several times.

2. Connect the power supply of the hair dryer, turn on the hot air to blow on the film, and tear it off by hand when you see that the film has small bubbles blowing. If it is difficult to tear off, use the prepared thin steel wool ball to rub slowly, being careful not to use force. If the hair dryer is not good, just wipe it with a rag dipped in white wine little by little, and quickly rub it with a steel wool ball after wiping, and it will soon fall off.

Wash the rag until there is no water left, and wipe the door again.

3. After removing the film on the door of the suit, the remaining offset printing is wiped off with some pen washing liquid dipped in facial tissue, and the glue part is automatically adsorbed on the facial tissue, and the viscosity disappears completely, and it can be easily swept away. If the area is not large, you can consider using eraser. If you have expired hand care products at home, you can apply it to the adhesive surface, because the binding water in the tape is supplemented, so the viscosity is reduced, and the effect of removing marks is very good.

There are many methods: 1. The area is not large, you can use banana water to rise, and then wipe it with a cleaning ball.

2. It can be removed with a cleaning agent for the textile industry (bottled called A1), I have tried it, and it is good.

3. Mix water with sulfuric acid, otherwise it will corrode, and wipe it with a cleaning ball after soaking.

4. The hair dryer blows the heat, and then peels it off or uses a wooden shovel to wipe off the glue marks with solvent oil.

5. Apply some wind oil essence (or other oily liquid objects) on the upturned edge, apply a little and then peel a little, then apply and peel again, and repeat several times.

Is it solid wood or paint-free?

This can be big or small, don't mess around, otherwise it will be ugly, and you will have to be beautiful in the later stage.

The safest way is to heat it with salt and put it in a small cloth bag, and then use this small bag to wipe the place with the protective film, and slowly remove it manually when the protective film is loose. If you blow directly with a hair dryer, the surface material is easy to peel, and the hot water is not good, and if the water seeps, the inside is easy to warp.

You can only tear it by hand, there is no other way.

To remove the protective film on the door, you need to be prepared: alcohol, hair dryer, scouring pad, rag, the specific removal steps are as follows:

1. First of all, take out the tools and materials you need for later use, as shown in the figure below.

2. Power on the hair dryer below, blow the protective film on the door with hot air, and wait until it bubbles.

3. Tear off the blistered protective film on the door.

4. Then use a scouring pad to wipe the remaining protective film on the door, taking care not to use too much force.

5. Then pour the alcohol into the rag and wipe the traces of the protective film on the door.

6. Finally, wipe the door clean with a damp rag.

1.If it is a large area of protective film, in order to avoid the protective film tearing unsightly, it is recommended to use an angle grinder to install a wire brush head to thoroughly polish the door and then re-paint, because simple removal will make the door ugly and will also destroy the paint layer and make the door rusty.

There is also a towel with boiling water to scald for a while, and then tear it by hand.

2.You can use a hair dryer to blow the protective film with a hot air gear, and after the glue is melted, it can be gently torn off. In addition, continue to blow the residual glue with blowing, and then use plastic film to glue the residual glue off.

Finally, wash it with water to make it look cleaner.

3.The membrane on the newly purchased stainless steel door is usually used to protect the door from scratches during handling.

Second, the solution:

1. Prepare tools: 1 hair dryer (with hot air), steel wool ball (slightly thinner steel wire), 1 bottle of liquor, 2 rags.

2. Film removal steps: connect the power supply of the hair dryer, turn on the hot air, blow on the residual film, and tear it off by hand when you see that there are small bubbles blowing up the film. If it is not easy to tear off, use the prepared thin steel wool ball to rub slowly, be careful not to use force, the paint on the stainless steel doors and windows may be damaged, and the wooden door can not be forced.

a.If the hair dryer is not good, wipe it little by little with a rag dipped in liquor, and rub it with a steel wool ball as soon as possible. Soon it dropped.

3. Wash the rag, wring it until it can't wring out the water, and wipe the door again.

2. Precautions:

1.After installation, how do you remove it?

a.First slowly uncover a seam, then rub oil (vegetable oil or lubricating oil is OK) into the seam, tear it down after dozens of seconds, and then repeat the above steps, you can tear it off.

b.The oil (vegetable oil or lubricating oil) can be wiped off after the tape is removed.

Here's how:

1: The area is not large, use banana water to rise, and then wipe it with a cleaning ball.

2: It can be removed with a cleaning agent for the textile industry, and it has been tried, and it is good.

3. Mix water with sulfuric acid, otherwise it will corrode, and wipe it with a cleaning ball after soaking.

4. The hair dryer blows the heat, and then peels it off or uses a wooden shovel to wipe off the glue marks with solvent oil.

5: Apply some wind oil essence (or other oily liquid objects) on the upturned edge, apply a little and peel off a little, and then apply and peel again, so that you can remove the protective film on the door repeatedly.

1: The area is not large, you can use banana water to rise, and then wipe it with a cleaning ball. 2:

It can be removed with a cleaning agent for the textile industry (bottled A1), I tried it, and it was good. 3. Mix water with sulfuric acid, otherwise it will corrode, and wipe it with a cleaning ball after soaking.

With degumming paper, the effect is very good. It is sold at a cleaning supply store or a hotel supply store.

I believe that the friends who decorate know that the door we buy will be covered with a thin layer of film, and the function of these films is to protect the door from being damaged by other materials. However, many friends, after the decoration, did not remove the film, resulting in a long time, the film on the door aging, it is very difficult to remove. If you tear it hard, it is estimated that you will be tired and your hands will be disabled.

So, are there any tips for quick removal? Next, Xiao Qi will introduce it to youHow to remove the film on the door

1. How to remove the film on the door.

1.If it is a large area of protective film, in order to avoid the protective film from tearing badly, you can use an angle grinder to install a wire brush head to polish the door thoroughly.

2. Heating method with hair dryer. Turn the hair dryer to the maximum, and then blow directly on the protective film for a while, the film will slowly soften by itself, at this time we can use an ordinary eraser or a soft rag to wipe off the offset print effortlessly, and remove the protective film smoothly. If there is still any glue left on it, we can continue to blow it with a blow dryer and then use the plastic film that has just been torn off to glue the remaining glue off.

Finally, wipe the door again with clean water to make it look cleaner overall.

3. Wind oil delicately remove the protective film.

If you don't remove the clean area, you can use wind oil essence to soak it completely, and wait until 15 minutes later, and then use a soft rag to wipe the place vigorously. If the dirt is still stubborn, you can extend the soaking time of the wind oil essence and then rub it vigorously until it is wiped clean.

3. White vinegar is also a good idea.

Dip a dry dishcloth in white vinegar or vinegar to completely cover the hard-to-remove parts and soak them completely, soak for 15-20 minutes, and then gradually wipe off along the edges of the film with a rag.

4. Lemon juice skillfully removes stubborn positions.

Rub the lemon juice repeatedly in the area where the self-adhesive stain is attached to it to remove the self-adhesive marks.

5. Medical alcohol immersion offset printing.

Drop an appropriate amount of medical alcohol on the surface of the film that is difficult to remove, and then soak it for a while. Wipe off with a soft cloth or paper towel. For example, expired perfumes or effective lotions can also be used to replace alcohol, because these are rich in alcohol, 6. Remove them with acetone.

Apply an appropriate amount of acetone to the film, then soak it for 10 minutes, and then wipe it off with a rag. This method is small and thorough, and the best part is that it removes these gelatin residues very quickly and easily, which is better than alcohol.

In addition to removing the door and window film, many items bought in the supermarket are sticky with stickers, which are also difficult to remove. At this time, don't tear hard, and the above methods are also applicable.