Why does the floor have to be raised when installing a squatting toilet in the bathroom?

In the construction standard, there is no requirement that the squatting toilet must be higher or flush with the ground, if it is on the first floor, the squatting toilet can be embedded in the ground and flush with the ground. However, flush is easy to cause water seepage, and it is difficult to use and take care of; If it's a high-rise, it must be above the ground. If there is no backwater bend and aqua privy.

There is no difference, the biogas rises directly indoors, and whoever has the bad habit of smoking in the toilet may ignite the biogas and burn the butt eggs, and it will also burn"House Sparrows"burnt taste.

<> know, sunken toilets.

The ground is relatively low and there are caissons, so there is enough height to install a trap to ensure the normal use of the squatting toilet, whether it is to install a squatting toilet or a toilet, it is okay, and there is no need to raise it. Most of the seats used are commercial houses in the north, and the bathroom sinks about 5 cm when designed. If it is changed to a squatting position, it is impossible for the floor to sink, it can only be lifted, and there is no need to lift it as a whole, as long as the squatting position is raised by thirty or forty centimeters, and a step is designed.

Take a second step at the position of the squatting toilet, so that the step is not too high, and it is a little more convenient to use. There is another way: just bury the squatting toilet on the step, and as for the sewer pipe, open the floor slab and go from the roof downstairs.

You must seal the water inlet hole of the squatting toilet, and then what you have to do is to insert the water inlet pipe into the water inlet hole, so as to avoid water leakage in the future use process. After the test, if it is found that there is no water leakage problem, the last thing to do is to fill, but when filling, we must pay attention to the place where the cement slurry and ceramics are in contact, we must smear some asphalt, so that it can be better used in the future.

Lightness is ceramsite.

One of the most important of these properties is its ability to replace heavy sand.

The main reason. The internal structure of ceramsite is characterized by fine honeycomb micropores. These micropores are closed, not connected.

The reason why the ground must be heightened is because the squatting toilet before installation is a concave shape, and the amplitude of the depression is about ten centimeters, and the recess is a pipe for water bend and drainage, and it is not possible to install it directly on the sewer, because the sewer is on the ground, and there is no concave space, so in order to make the squatting toilet a plane, the ground can only be raised, and then a hole is left, and this hole is used to put the depression of the squatting toilet into it. Then smooth it with cement and lay the tiles on it.

Because in this way, it will not be affected by other things, it can be more convenient, so that it can be more fashionable.

If there is no difference between this backwater bend and a dry toilet, the biogas will rise directly into the room, and whoever has a bad habit of smoking in the toilet may ignite the biogas, burn the fart like an egg, and produce a burnt smell of burning "house birds".

In the construction standard, there is no requirement that the toilet must be higher or flush with the ground, if it is on the first floor, the toilet can be placed on the ground and flush with the wooden floor. However, flush level is easy to cause water leakage, and it is very difficult to use and manage methods; If it's a high-rise building, it must be higher than the ground. With everyone attaches great importance to the difficult problems of bathroom odor and water leakage, the toilet has also been updated, the absolute height of the general toilet is 280mm-320mm, and the absolute height of the toilet with a water trap is 300mm-350mm, which needs to be higher than the ground when assembling.

At the beginning, the toilet is higher than the floor of the bathroom, which can form a certain fluctuating absolute height, which is conducive to the smooth drainage of the bathroom, so that there is no need to worry about the blockage of the sewage pipe, and the difficulty of water leakage and leakage. Secondly, the toilet is higher than the ground, which is cleaner and more convenient to use. It forms an isolation zone with the undulation of the bathroom floor to ensure the cleanliness and tidiness of the bathroom.

Finally, the toilet is higher than the ground, which is conducive to the maintenance of the ground structure, especially above the first floor, to avoid digging down to damage the ground structure and injure the neighbors next door.

If you talk about your family's new opening real estate, the current real estate developers are all caisson scheme design. Caissons are generally 30 cm deep. Installing a toilet is a relative height in many ways.

You don't have to lift the ground. If it's an old community, then this method won't work. If it is said that the bathroom of the rural villa is made on the first floor, you can dig a pit directly in the ground, which can solve the difficulty of putting toilets.

And don't pull up the ground either. There's also a way to buy one that has a toilet with a toilet. It's dual-purpose.

All of them can solve the difficulty of lifting the floor of the toilet. And it's easy to install and easy to use. It can also solve the disagreement between relatives in choosing a toilet is a toilet.

Everyone should find the installation location of the toilet, and then leave a pipe here, but remember that the water pipe and the road must maintain a certain distance. After finding a part, the next thing to do is to make a dent, this relative height must be higher than the toilet, so that when assembling in the back, it will save costs.

You can lay some floor tiles on the ground, and then increase the height of the squatting urinal on the ground, so that the design can be realized.

Cut the concrete in the squatting area, then dig enough to dig a pit in the area, then use concrete or cement mortar to make the pit waterproof, and finally install the squatting in this position. This also completes the installation of the squat at the same height as the ground.

It can be heightened by 20cm with cement, which can improve the experience of going to the toilet.

It can be heightened with floor tiles and cement underneath, and then tiled on the surface.

The ground can be raised so that the problem is solved, backfill can be done, or a few steps can be added.

As follows: 1. Split squatting toilet.

The squatting toilet itself does not have a water trap, and the trap is separated, which is called a split squatting bend, which is easy to install, has a large water flow and sufficient momentum. The disadvantage is that it is more difficult to clean and it is difficult to take things out when they fall. In addition, if the plumbing does not have its own drain bend, the sewer odor is easy to flood.

2. Siamese squatting toilet.

The squatting toilet comes with a trap, which is called a one-piece squatting toilet. The biggest advantage of the one-piece squatting toilet is that it can use the bend of the water storage bend to create a water seal to prevent the odor from the sewer from flowing backwards. The disadvantage is that compared with split squatting toilets, conjoined squatting toilets are easy to clog and are not easy to dredge.

The bathroom is not sunken. Is it necessary to raise the ground to install squatting poop? How much does squatting generally elevate?

The bathroom is not sunken. Is it necessary to raise the ground to install squatting poop? How much does squatting generally elevate? Kiss! Hello, happy to answer your <>

If you live upstairs or downstairs, if you live on the first floor, you can dig down 1, if you live upstairs or downstairs, if you live on the first floor, you can dig down, you can dig down 30cm; After the floor is covered with concrete and waterproofing. 2. If you live upstairs, you must raise the ground 200 high, and 180 is the lowest line.

3. Generally, the squatting toilet is 18-26cm high, you must first choose a good squatting toilet, compare it to do, when choosing a squatting toilet, you should also pay attention to the direction and length of the squatting toilet outlet, whether it can be connected with your bathroom sewer, pay attention to whether it is the front mouth or the back mouth, in short, you must measure well to choose the right one, so as to raise the ground according to the height of the toilet. Extended data installation standard 1, according to the sewage outlet of the installed product, reserve the sewer pipe at the appropriate position from the wall, and determine the distance between the sewer pipe inlet and the ground plane at the same time. 2. The depth of the pit reserved for the installation of the squatting toilet under the ground is greater than the height of the toilet.

3. Put the connecting rubber plug into the water inlet hole of the squatting toilet and clamp it tightly. Apply a layer of glass glue or putty to the outer edge of the water inlet hole of the squatting toilet, and insert the water inlet pipe into the water inlet hole of the rubber plug so that it is well sealed with the rubber plug to prevent water leakage. 4. Coat a layer of glass glue or putty on the edge of the outlet of the squatting toilet, put it into the inlet of the sewer pipe and twist it, and set the toilet horizontally with coke slag or other fillers.

5. Open the water inlet system, check whether there is water leakage at each joint, and if there is water leakage, check the situation at each joint. until the problem is resolved. 6. After checking that there is no water leakage at each joint, fill the toilet around with filler, and fill the contact surface of ceramic and cement mortar with elastic materials such as asphalt or linoleum of more than 1cm.

Use cement mortar to fix the squatting toilet in the horizontal plane, and after it is stable and firm, then pave the bathroom floor tiles on the cement surface. Test flushing, if there is no abnormality, you can use it. Hope mine can help you <>

Do you have any other questions?