What do I need to pay attention to when installing squatting in the bathroom? Are there any requirem

What do I need to pay attention to when installing squatting in the bathroom? Are there any requirements? Most girls will encounter it.

While shopping outside, I found a long queue when I went to the toilet and it was clear to me that there was no one and I walked past and it was a toilet. While the toilet looks cleaner, the squat is still very wide.

How to install a squatting toilet in the bathroom.

Is it effective to use the toilet?

1.bathroom squat installation.

Depending on the sewage port where the product is installed, the low water pipe is kept at a suitable location on the wall, and the distance from the inlet surface of the lower water pipe is determined.

2.The depth of the installation is kept in the ground, and the depth depth is greater than the height of the manifold.

3.Place the jet plug into the squatted air intake. A layer of glass glue or fly ash is applied to the outer edge of the spray inlet hole, and the water pipe is inserted into the water appliance so that it is well sealed to prevent water.

4. When operating, apply a layer of water to the air outlet and put it into the inlet of the sewer, then use the focus or filling to set the squatting toilet.

5.Once done, turn on the faucet for system testing to see if there is a leak at the junction, and if there is water, check the joints of each joint until the problem is resolved.

6.Finally, it is necessary to fill the squat, and then fill the contact surface of the product and the cement slurry with an elastic material such as bitumen or linoleum. The squatting toilet is fixed with cement pulp, and then the floor tiles are stored.

7.Try the water again, and if there is no abnormality, you can use it.

4.The inlet of the squat tube mainly has high tank rinsing, ball valve, delay rolling valve, solenoid induction roller valve, manual flushometer and so on.

5.The process of installing and using the squat is to avoid strikes.

First, install a squatting toilet, to see whether it is front drainage or rear drainage, and pay attention to burying pipes when decorating. Second, the water pipe of the wall inlet tank should be laid in advance. Third, to build the countertop, squatting is buried under the ground.

When installing the squatting toilet, you must first measure the size of the squatting toilet, and reserve the installation position according to its size, and fill the core with mixed mortar in the installation position, and must not install it with cement, otherwise the cement will squeeze and expand the squatting toilet. During the installation and use of the squatting toilet, it is necessary to avoid slamming into it.

When installing squatting stool, first of all, we should pay attention to measuring the size, and secondly, leave a good position, and do not use cement to install, because cement will have thermal expansion and cold contraction, which will destroy the squatting toilet, and we should be careful when installing squatting stool.

<><What are the precautions for the installation of squatting toilets

1. When installing the squatting toilet, be sure to measure the size of the squatting toilet first, and reserve the installation position according to its size. The installation position should be filled with mixed mortar, and must not be installed with cement, otherwise the cement will squeeze and squeeze the squatting toilet.

2. Be sure to remember to apply a layer of butter or asphalt to the installation surface of the squatting toilet, so that the isolation of the squatting toilet from water mortar will protect the product from swelling and cracking. When finishing with heat-dissolved asphalt, it is necessary to pay attention to the prevention of the squatting toilet from being heated and causing it to break.

3. If the squatting toilet does not have a water storage inlet, a water storage inlet should be set on the pipeline, which can play the role of odor insulation. If the squatting toilet has its own water storage inlet, the sewer pipe does not need to be equipped with a water storage inlet, otherwise the flushing function will be affected.

4. The water inlet flushing device of squatting toilet socks mainly includes high water tank flushing, ball valves, delay flushing valves, electromagnetic induction flushing valves, manual flushing valves, etc.

5. In the installation of the squatting toilet and its use process, it is necessary to avoid violent impact.

1. When installing the squatting toilet, please measure the size of the product first and reserve the installation position according to the size. The installation is filled with mixed mortar, and it is strictly forbidden to install with cement, otherwise the condensation and expansion of cement may squeeze the toilet. X0D X0A2, apply a layer of asphalt or butter on the installation surface of the squatting toilet to isolate the squatting toilet from the water mortar and protect the product from swelling and cracking.

Toilet squatting toilet installation construction method.

Although the toilet has become the choice of the general family, when it comes to hygiene, the squatting toilet is still the best choice. So, how to install a squatting toilet? Especially in this kind of high-rise community, the installation of squatting toilets is a technical job.

In fact, the installation of the squatting toilet is not a difficult task for professional masters, but if the owner wants to install it himself, it is quite difficult. No, I just didn't listen to my wife's advice at the beginning, so I had to install a squatting toilet by myself, which made the bathroom smelly. So, what are the particulars of how to install a squatting toilet?

Next, listen to the explanation of the master who has been decorating for more than 30 years! If you want to install it yourself, you may wish to learn it

1. Determine the distance between the inlet of the water pipeline and the ground.

According to the sewage outlet of the product to be installed, the water pipe is reserved at the most suitable location from the wall, and the distance between the sewer pipe entrance and the ground needs to be determined.

Second, the depth of the pit should be greater than the height of the squatting toilet.

The next step is to dig out a pit that is used to hold a squatting urinal. It should be reminded that the depth of the pit must be greater than the height of the squatting toilet.

3. Do a good job of waterproofing the squatting toilet.

The next step is to connect the rubber plug, put it at the water inlet of the squatting toilet and clamp it tightly, coat the outer layer of the water inlet hole with a layer of glass glue, and then insert the water inlet pipe into the rubber plug water inlet hole.

Fourth, use filler to set the squatting toilet horizontally.

It is also necessary to apply glass glue to the edge of the squatting toilet, put it into the inlet of the sewer pipe and screw it, and then set the squatting toilet horizontally with the help of filling.

5. Open the water inlet system to check each joint.

After the squatting toilet is erected, the most critical thing is to open the water inlet system to check whether there is any leakage at each joint. If there is a problem, it is necessary to clearly check the joints until all the problems are solved.

Sixth, the squatting toilet is filled with solid surrounding.

If there is no leakage at the joint, then the area around the squatting toilet needs to be filled with filler. It should be reminded that the contact surface of cement mortar and ceramics needs to be coated with a layer of asphalt.

7. Lay floor tiles after completion.

Finally, the squatting toilet is fixed in the level with cement mortar, and after it is fixed, a layer of floor tiles needs to be laid. If you want to test whether the installation of the squatting toilet is successful, you can try to flush it after the floor tiles are laid, and if you find that there is no abnormal situation, it proves that the installation of the squatting toilet is complete, and there will be no bad situation of anti-odor!

1. Sink the squatting toilet and install it

What does it mean to sink the squatting urine? To put it simply, the squatting toilet is installed under the ground using the structure of the actual floor of the toilet, that is, all the drainage facilities such as the water trap at the bottom of the squatting toilet are installed below the ground. To choose this installation method, you need to meet the following two points:

The sunken toilet itself has a sunken structure with a depth of about 30 cm and 40 cm, and it is completely possible to sit the squatting toilet in the caisson by installing a squatting toilet. At this time, in fact, the area where the squatting is installed is cut out, and then the squatting support is done from the inside of the caisson, and the installation is finally completed. After installation, the surface of the squatting toilet is the same as the floor of our bathroom.

What is the first floor of the bathroom? This means that there is no ground floor with a basement, and the floor of the bathroom is covered with soil. When installing a squatting toilet, people need to cut the concrete of the squatting area, then dig a pit suitable for the squatting toilet in this area, and use concrete or cement mortar to make waterproofing, and finally install the squatting poop to this position.

2. Partially raise the ground to install a squatting toilet

Partial elevation of the floor refers not to elevate the floor of the bathroom, but to elevate the lower part of the squatting installation position. Because the size of the squatting itself is about 60 cm to 50 cm, the squatting toilet can only be installed if it is raised.

First of all, people should choose the squatting toilet to be installed. Since the squatting toilet is only partially raised on the ground, people need to determine the size of the squatting urinal. After that, according to the size of the squatting urinal, draw the area occupied by the squatting on the ground.

After the location is marked, people can build the buttresses of the squatting surface according to the signs. It is common to use a brick foundation as a squatting pier, then fill the brick pier with sand as it is, and finally install the squatting urinal to this partially raised position.

Due to the partial elevation of the squatting toilets, the surface layer of these areas needs to be retreated, i.e. tiled. When laying tiles, the surrounding façade walls on the side of the squatting should be tiled at the same time, so that in the end, only the position of the squatting toilet is too high, and the rest of the place is still horizontal.

3. Choose an integral squatting toilet

The overall squatting toilet refers to the lower part of the squatting toilet without making the corresponding buttresses, all its drainage and water storage are in the built-in structure, and the installation steps are as follows:

Decoration of the ground. Ground decoration refers to the tile paved on the floor of the bathroom, people need to complete the tiling, and then the position of the squatting sewer pipe is also paved with tiles, and at the same time, the sewer pipe of the squatting toilet meets a certain installation height according to the requirements of large volts.

Install the finished product as a whole squat. The installation of the finished product as a whole means that the squatting toilet is placed directly on the upper part of the drainage hole, and then the lower part of the squatting toilet is fixed with the tile, and finally connected to the water, and the squatting toilet is installed.

In the installation of squatting in the bathroom, people must choose the installation method of imitating Qingshi according to the actual situation of the bathroom, so as to avoid problems in the later stage.

Although toilets are now installed in the majority of bathrooms, many families choose to install squatting toilets. There are many types of squatting toilets, and the installation methods of different styles are also different, are you also confused? In this issue, let's take a look at the installation method of the toilet squatting toilet, I hope it will be helpful to you.

How to install the squatting toilet

1. Before installing the squatting toilet, check whether there are foreign objects in the sewage pipe and the channel in the product.

2. Try to fix the installation position and height of the squatting stool, as well as the docking of the sewage outlet and the sewage pipe, and then take the squatting toilet away.

3. Install the water inlet and water tank, the inner diameter of the water inlet pipe is about 28mm, and the distance from the bottom of the water tank to the water inlet of the squatting toilet is 1500mm-1800mm, if the installation of the pipe type hand pressure is above, the water consumption is 9 liters.

4. After the flange rubber ring is sleeved into the water inlet pipe, it is docked with the water inlet of the squatting toilet, and then the installation surface of the squatting toilet must be fixed, and the front, back, left and right of the squatting toilet must be leveled with a level, and then the product sewage outlet and the sewage pipe interface must be sealed with glass glue or cement sand paddle.

In our lives, we always have to use squatting toilets, and we know that many people have installed squatting toilets in their homes, so it can be seen that squatting toilets are very important for our lives, so when we choose a squatting toilet, the next step is to install the squatting toilet, then if we want to install the squatting toilet correctly, we must also understand some correct installation methods, so that we can. Let's introduce to you what are the installation methods of squatting toilets? and what are the related precautions.

Introduction to the installation method of toilet squatting toilet

1. When installing the squatting toilet, the sewer pipe should be reserved at the appropriate position from the wall according to the sewage outlet of the installed squatting toilet, and the distance between the sewer pipe entrance and the ground level should also be determined.

2. When installing the squatting toilet, it is required to reserve the depth of the pit under the ground, and remember that the depth must be greater than the height of the squatting toilet to facilitate installation.

3. Put the connecting rubber plug into the water inlet hole of the squatting toilet and clamp it tightly. Apply a layer of glass glue or putty to the outer edge of the contact with the water inlet hole of the squatting toilet, and insert the water inlet pipe into the water inlet hole of the rubber plug so that it is well sealed with the rubber plug to prevent water leakage.

4. During installation, it is necessary to coat a layer of glass glue or putty on the edge of the water outlet of the squatting toilet, put it into the inlet of the return limb sewer pipe and screw it together, and use coke slag or some other filler to erect the squatting toilet horizontally.

5. After installation, open the water inlet system for testing, check whether there is water leakage at each joint, if water leakage occurs, you need to carefully check the situation of each joint until the problem is solved.

Introduction to the precautions for the installation of toilet squatting toilets

1. After checking that there is no water leakage, you can fill the area around the squatting toilet with filler, and at the same time fill the contact surface between the ceramic and the cement mortar with more than 1cm of asphalt or linoleum and other elastic materials. Use cement mortar to fix the squatting toilet in the horizontal plane, and after it is stable and firm, the floor tiles can be paved on the cement surface. Try flushing again, if there is no abnormality, you can use it.

2. After checking that there is no water leakage at each joint, fill the toilet around it with filler, and fill the contact surface between the ceramic and the cement mortar with more than 1cm of asphalt or linoleum and other elastic materials.

3. Fix the squatting toilet in the horizontal plane with cement mortar, stable and firm, and then pave the leaky bathroom floor tiles on the cement surface. Test flushing, if there is no abnormality, you can use it.

What we have introduced to you above is about how to install the squatting toilet and what are the precautions when installing? We should have some understanding of this aspect of the problem, we know that we are not a professional installation master, so before the installation we have to have a general understanding of the whole process, such empty words, we can correctly install the squatting toilet, I believe that after reading the above introduction, there should be a general understanding of it, I hope our content can help you.

You can get it for free