Why do you use a special floor tile push pull knife to cut the floor tiles and still lose the corner

Updated on home 2024-07-17
4 answers
  1. Anonymous users2024-02-12

    One is speed, the second is strength, and the third is that the cutter head is not sharp enough, change to imported or pure steel, try to draw hard!

  2. Anonymous users2024-02-11

    1. The reasons for the lack of corners of the tile during cutting: 1. The yuan pin protects the hose; 2. Asymmetry of turns; 3. Tile tile quality problem. 2. Solution:

    1. Replace the yuan pin hose shirt, such as; 2. Correcting the turns; 3. Try other ceramics. 3. Precautions for cutting: 1. When cutting, drag the "handle" backward to the highest control position to avoid collision between the blade and the tile, otherwise, the blade will be unable to be used due to defects.

    2. For antique or other convex and concave tiles such as non-planes, please replace the cutter head for poor pants! Tiles with coarse surfaces will shorten the life of the blade. 3. Do not use the blade to press the broken bricks during the operation.

    4. When cutting, first pull the push-pull rod to the rear end, let the blade or Qingqi lightly press on the tile, push forward along the spindle to the front control groove, put the presser foot on the tile, and gently hit the end of the push-pull handle, and the tile can be broken with the knife marks.

  3. Anonymous users2024-02-10

    Hello, when the floor tiles are paved, they need to be cut and treated many times to adapt to different shapes and sizes such as wall corners, ceilings and floors. Although the special floor tile push-pull knife can effectively cut the floor tiles, in the process of fighting, if the force is uneven or the angle is not accurate, it may cause the corners of the floor tiles to fall. In addition, the material and quality of the floor tiles will also affect the fragmentation of the floor tiles, if the quality of the floor tiles is poor, or the material is uneven, it is easy to fall out of the stupid situation.

    In order to avoid the corners of the floor tiles, you can check the quality and material of the floor tiles before cutting, and choose the best and uniform floor tiles for paving. At the same time, when using the floor tile push-pull knife for cutting, it is necessary to master the correct use method and angle, apply force evenly, and avoid excessive pressure and inaccurate angle base holding. In addition, the use of professional tools and equipment can also effectively reduce the situation of floor tiles falling corners.

  4. Anonymous users2024-02-09

    After the floor tile is broken, it can be treated according to the degree of damage, generally speaking, there are three main ways: covering, repairing and replacement.

    Let's start with the cover-up method.

    If you can be sure that the damaged floor tiles will still hold firm, it will be easier and more convenient to cover them up with some decorative objects. If it is a wall tile, you can consider whether it can be covered and decorated by fixing decorative paintings and corresponding hardware pendants on it; If there is a crack on the ground, see if it can be covered by furniture and other items in the future.

    Next, let's talk about the patching method.

    The old porcelain bricks are still intact, but they are separated from the junction with other finishes, and the sand and ash at the joints should be removed when repairing, and epoxy resin adhesive should be injected, and then the joints should be repaired with waterproof flexible caulking materials (such as glass glue) after drying.

    Sometimes old tiles are broken only.

    One or two pieces, and the original cement mortar is difficult to chisel off or chisel hair. At this time, you have to use epoxy resin glue (all-purpose glue) to apply a thin layer on the back of the tile and the cement wall, and then press hard to ensure that the new tile is flush with the surrounding tiles. If the mortar is not loose, only the tile falls off, the mortar on the tile can be scraped clean, mixed with a little cement in 107 glue to form a paste, evenly coated with a thin layer on the back of the tile, and then pressed the tile to stick firmly.

    If the mortar falls together with the tiles, first gently chisel some pits on the original foundation surface, re-inlay them with mortar mixed with 107 glue, and then press the fallen tiles until the mortar hardens.

    Method of replacing floor tiles.

    1. Remove the caulking white cement along the edge of the tile, and carefully remove the damaged tile with a small chisel. If the surrounding tiles are firmly pasted and you don't want to replace all the surrounding tiles, you can use a glass cutter to carve the middle of the tile, chisel the middle part of the tile first, and then use a sharper steel chisel to slowly repair the broken porcelain blocks around the edge.

    2. After the tile is chiseled off, the bottom cement mortar should be chiseled off with a steel chisel, and the force should not be too heavy, otherwise it will shatter other intact tiles, and the surface should be moistened with water after removing the dust.

    3. Before pasting tiles, the porcelain should be soaked in water and moistened with water, and after drying, a layer of 107 glue cement slurry should be thinly scraped on the back of the tile, and then pressurized in place, and check whether the newly pasted tiles are flush with the surrounding tiles.

    4. The joints of the newly pasted tiles should still be filled with white cement slurry, and the excess cement slurry on the tile surface should be removed.

Related questions
10 answers2024-07-17

This is because of the floor tiles.

The surface strength is not enough to be worn, the following is the method of removal, the specific operation process is described as follows: >>>More

12 answers2024-07-17

There are several reasons why it is necessary to lay the line when laying floor tiles: >>>More

11 answers2024-07-17

Landlord,It's humorous.。。 This question, you have to ask the first person who said that the zombie jumped this one! ~。

9 answers2024-07-17

Yes, it's absolutely economical and affordable!

4 answers2024-07-17

Why do you have to cover the signboard with red paper before the new opening? >>>More