Why does rubbing the floor tiles with steel wool leave black, and how to remove them

This is because of the floor tiles.

The surface strength is not enough to be worn, the following is the method of removal, the specific operation process is described as follows:

To remove the black scratches left by the friction of the steel wool balls, you need to prepare: water, toothpaste, rags, dish soap.

Brush. 1. First of all, squeeze an appropriate amount of toothpaste on the black scratches left by the friction of the steel wool ball on the floor tiles.

2. Then pour an appropriate amount of laundry detergent on the black scratches left by the friction of the steel wool ball on the floor tiles.

3. Brush the black scratches left by the friction of the steel wool ball with a brush as shown in the figure below.

4. Then rinse the black scratches left by the friction of the floor tiles by the steel wool ball with clean water.

5. Wipe the black scratches left by the friction of the floor tiles by the steel wool ball with a rag.

The black marks left by rubbing the floor tiles with steel wool balls can be removed with five cleaning powders (high-efficiency decontamination powder).

Specific method: Soak the black mark of the floor tile with water, sprinkle it with five cleaning powder, and then wipe it repeatedly with a scouring pad. Finally, wipe the stain clean with a clean, damp towel.

Hello! I wipe it with the green umbrella brand "five clean powder" and can remove it. Only you can't wipe it, but you can't wipe it off. The floor tiles are wiped with steel wool balls, leaving black metal scratches, which can be wiped off with five cleaning powders.

It may be ...... iron powderTry ...... with acid

The surface strength of the floor tiles is not strong enough, it is worn out, you try it with toothpaste.

Hello, I am glad to serve you, and the answer is as follows: Since the cleaning ball is made of metal, cleaning the tile with a metal cleaning ball will cause black scratches (metal scratches) due to the friction of the tile by the cleaning ball. There is no damage to the tile itself, it can be removed.

First polish the tile scratches, then wax and polish. Method 3: Use a sponge to dip the detergent and carefully wipe the scratches to remove.

Since the cleaning ball is made of metal, cleaning the tile with a metal cleaning ball will cause black scratches (metal scratches) due to the friction of the tile by the cleaning ball. There is no damage to the tile itself, it can be removed. Method 1:

Method 3: Use a sponge to dip the detergent and carefully wipe the scratches to remove. Toothpaste rubbing, or sandpaper dipped in water, multi-functional cleaning paste on the net, the rest of the rubbing stainless steel rod is excellent, versatile, shiny.

No, it's gone after wiping the glossy surface, it's all scratches.

If it is stained with rust, you can squeeze the juice of fresh lemon on the rust stain and rub it repeatedly, and then wash it off with soapy water. If you don't have fresh lemon, you can also use vitamin C tablets instead, and if you get soy sauce, vinegar, etc., you can use toilet cleaner.

Stains such as tea, ice cream, and beer can be removed with a soda ash solution such as sodium hydroxide or potassium bicarbonate. When processing, you should use a board brush, do not use steel wool, otherwise it will scratch the surface of the tile, and it will be difficult to deal with stains.

If the surface is stained due to burning, you can use fine sandpaper to gently sand, and then apply the sealing agent and polishing agent, you can restore the original state, daily cleaning can be first wiped with an ordinary cloth like wiping the cement floor, and then dry with a dry cloth.

1. You can squeeze some toothpaste on the black scratch first, and pour some laundry detergent on it;

2. Then wipe the black part vigorously with a paper towel or dry cotton cloth, and wipe it several times;

3. Then rinse with water; Finally, wipe it dry with a dry rag, and you can see that the black is gone.

It is very troublesome to clean up the vitrified bricks stained at home, many owners have a headache, if you ignore and clean up for a long time, it is very difficult to clean it up, and it will appear that our living environment is very dirty, which affects the mood very much; Many owners will also encounter the traces of vitrified bricks by Chinese businessmen, which also affects the aesthetics very much, so let me explain to you the relevant knowledge of vitrified bricks today.

1. How to remove the penetrating stain of vitrified brick.

1. Sediment, rust, mortar.

The cleaning of this kind of contaminant is more complicated, and some chemical reagents are needed to clean up, first of all, we first use a few drops of sulfuric acid or hydrochloric acid solution on the brick surface, and wipe it after standing for a few minutes.

2. Paint, drawing pen.

You can choose the toothpaste commonly used in our home life to remove stains, and the effect is also very obvious.

3. Soy sauce, vinegar and carbon powder.

It is better to use toilet cleaner, or you can use dish soap and soapy water to clean it.

4. Tea, ice cream, grease and beer.

The cleaning of this type of stain is relatively simple and can be cleaned with a soda ash solution.

5. Glue hammer printing.

This is more difficult to clean, you need to contact the 20%-40% concentration of sodium hydroxide solution after soaking for a day and night, and then use a concentration of 30%-50% hydrochloric acid solution to soak for half an hour and then wipe it clean with a rag.

6. Lime scale.

Acidic detergents can be used to wipe off.

Second, how to repair the vitrified brick after being scratched by iron.

1. Clean up the scratched area of the vitrified brick.

First of all, the scratched area must be cleaned up, otherwise there will be residues during treatment, and it is not easy to carry out follow-up treatment.

2. Sprinkle toilet cleaners on the scratches.

Then sprinkle the toilet cleaner on the scratches, wait for a few minutes, and rub the scratches repeatedly with a clean and soft cloth, with moderate strength, without too much effort. When the scratches slowly disappear, use a paper towel or rag to clean the toilet cleaner, you will find that the scratches are gone, and the vitrified bricks will look new.

Precautions: Since the toilet cleaner is corrosive to **, you can wear a thicker glove during the operation in case ** is corroded.

The above is the relevant knowledge shared for you about how to remove the vitrified brick seepage and how to remove the stain and how to repair the vitrified brick after being scratched by iron, I hope it will help you. If you want to know more about vitrified tiles, please stay tuned.

Summary. Hello, according to my understanding, if the steel wool ball brush tile is blackened, it should be the glaze of your tile surface has fallen off, in this case, you can only try to use the way of grinding and polishing, which can have a certain effect. You can squeeze some toothpaste on the black scratch area and pour some laundry detergent on top of it; Then use a paper towel or dry cotton cloth to vigorously wipe the black area, and wipe it several times; Then rinse with water; Finally, wipe it dry with a dry rag, and you can see that the black is gone.

Hello, according to my understanding of the crack Feng Chong, the steel wool ball brush tile grinding ground state black, should be your glaze on the surface of the tile glaze off, this situation can only try to use grinding and polishing, which can have a certain effect. You can first squeeze some toothpaste on the black scratch and pour some laundry detergent on it; Then use a paper towel or dry cotton cloth to vigorously wipe the black area, and wipe it several times; Then rinse with water; Finally, wipe it dry with a dry rag, and you can see that the black is gone.

Thank you, I hope mine will help you, praise oh dear.

I just wiped it today, will I see it tomorrow.

Tomorrow it will be shallow.