How to remove the label that is difficult to tear, and how to remove the label

1.Apply a little hand cream to the adhesive tape.

Apply an appropriate amount of hand cream to the adhesive tape that needs to be removed. Then for half a minute, rub your fingers constantly on the surface of the adhesive tape. When half a minute is up, gently remove the adhesive tape and wipe off the slight residue on it.

In this way, a perfect, glue-free dish appears.

2.Make use of a hair dryer.

Use thermal expansion and contraction to raise the temperature of the hair dryer. Turn on the switch and let it stand for 10 seconds, blow the hair dryer on the plate for half a minute, touch the temperature of the surface of the tape, and start tearing the tape when it is a little hot. However, it should be noted that if the container itself is not heat-resistant, then this method should not be used.

High temperature heating may melt and deform the container, and may even release toxic gases, which is very bad for human health.

3.Wipe with an eraser.

In the face of a lot of stubborn glue marks, it is the kind of situation where the sticker has been cleaned off, but the glue marks are still on the surface and cannot be removed. In fact, through the friction of plasticine, these glue marks will be continuously removed, making the surface of the bowl wall smooth and clean.

4.Clean with dish soap.

As a powerful stain remover, dish soap is also easy to deal with in the face of stubborn guys like adhesive tape. The way to remove it, of course, is to apply dish soap to the adhesive surface, leave it for a while, and then start washing it. If the hand buckle still doesn't come down, you can use some tools, such as a dishwasher, or a steel wool ball.

Have you all learned these ways to remove small labels? It's very effective.

How can the blue label be removed? One uses a hair dryer to blow it hot later. Slowly dying, and then again. Apply the wind oil essence to it. After a while. And it was lost.

First of all, such a tool can be easily spotted:

1. A hair dryer. This is the most important tool, and the whole set of tools in the core tool, but be aware that we are using a hair dryer for heating, so be sure to be able to blow relatively hot wind, ordinary hair dryers may not work properly, older ones are better.

2. Insert one. An ordinary utility knife is sufficient, but not a knife. A blade may need to be used on special occasions.

3. Be attentive to one. The work is actually very simple, but the most important thing is that you have to be careful before succeeding.

Two, occasion.

This experimental method is suitable for the following situations:!

1. Smooth the things on the sticker, the self-adhesive paper on the packaging box is pasted on the packaging box, 3, the computer accessories or mobile phone, the paper label, 2, as shown in Figure 4, after finding that the glue composition will pass through a part of the characters on the left side of the various anti-counterfeiting labels.

Three specific methods.

1, The first case is the easiest to deal with, scrape one with a blade to start, and then slowly tear it by hand. If the speed is too slow, slightly heat the hair dryer provided.

2. In this case, it is more difficult to deal with, especially the kind of pattern printed on the kind of belt. The computer desk is heated with a blade that can be opened to a weak windshield at the beginning, focusing on the heating belt at the back, be careful not to overheat, it will blow the tape deformed. The whole process of slowly tearing the hand must be done with caution.

This may have something to do with many aspects, but as long as the technology is skilled, it can still be satisfactory in most cases, so the specific impact of resealing is not easy to find without looking closely.

3. In this case, you can scrape off directly with a blade, slowly, a thinner blade may be required in some cases, at this time, the blade can be used. If the label is large, a hair dryer can be used to assist in heating.

4. When this label is generally smaller, you can use the blade to float the corner, heat it with a hair dryer, and slowly pick up the whole label. The handling of this label must be cautious before careful care, it will leave residual traces, and there is no success.

5. It can be used to deal with this trick. General heating is definitely not possible, because the plastic film is also blown and deformed. The method is simple:

Tear directly by hand, not slowly, be sure to be fast, because the larger label, which can be divided into several times, is torn by hand suddenly and quickly. In this case, the ambient temperature is kept as low as possible.

Have you ever torn a label, but you can't tear it clean? Let me tell you how to do it.

01 Wind Oil Cover Hongjing: If you want to tear a label clean, then you can use things and book Wind Oil Essence. Wind oil essence should be available in every household, pour wind oil essence on the label, and then rub it vigorously.

02 Hair dryer: If you want to tear a label clean, you can use a hair dryer to blow this label for about 15 minutes. This makes it easy to get the label down.

03 Nail polish remover: If you want to tear a label clean, you can pour nail polish remover over the label. If you're a polish-wearing girl, then you definitely have this.

04 Alcohol: If you want to tear a label clean, you can pour alcohol over the label. Then rub it vigorously so that the label comes down easily.

After buying a new item, the label on it will always affect the beauty of the item, and it is difficult to tear it clean if you tear it casually, so you should also pay attention to the reasonable method when tearing the label. There are several main ways to peel off the label:

1. Blade method.

Usually, when the label fails, it will be scraped off with a razor. So it's better to scrape with a blade at the beginning, be careful when scraping, don't hurt your hands, and then you can carefully scrape off the whole sheet along the edge. Of course, this method is more suitable for trying on flat objects.

2. Eraser method.

There will be glue residue after the label is removed. At this time, if you can't get it off and can't get wet, you can use an eraser to wipe it. By rubbing the rubber to adsorb the glue, the glue can be cleaned very quickly. You can give it a try.

3. Hot water method.

Labels are generally glued with self-adhesive, as long as the temperature is hot enough, the glue will be very easy to tear off after it has melted back. Generally, it is suitable for tableware such as bowls and plates, and after soaking for more than 10 minutes, it can be gently wiped off with a wire ball. It should be noted that some heat-resistant plastics should not be soaked in hot water in the end, as they are easy to deform.

4. Hair dryer method.

Turn the hair dryer to the hot windshield and blow the label, and you can easily tear the label off. However, it should be noted that you must use a hair dryer with higher power and higher temperature, otherwise the effect will not be good. After tearing off the label, just wash it with clean water again.

There will be labels on the goods we usually buy, what should we do if we can't tear them off? Let me tell you how to tear off the label.

01 Tear it off first: We usually buy things in the store and come back, and there will be a label on the product. Tear off this label first, and there will be some sticky residue. Branches.

02 Wind Oil Essence: We prepare a wind oil essence, drop a few drops of wind oil essence on the area that is torn off, and then rub it repeatedly with your hands. That's it.

03 Nail polish remover: In addition to wind oil essence, there is another tool that can be replaced by nail polish remover. I believe that many girls have this, just apply it to the sticky place.

04 Hair dryer: If the product has a label, you can use a hair dryer to blow it. Turn the hair dryer on the maximum block of hot air and blow it at it.