What kind of wood is good for drill boards, and what kind of drill bits are used for wood drill bits

Natural oak is better.

Moderate softness and hardness, not easy to hurt the knife, not easy to deform, not easy to burst; No wood chips are produced when used; Moisture-proof and mildew-proof; Natural sterilization, easy to clean; Tough and heavy; The shape is simple, beautiful and generous, durable, and it is a rare kitchen helper.

Hello! You should be talking about "chopping board", right? If so, it's what is commonly referred to as a cutting board.

If it is a cutting board, it is generally made of camphor wood, oak, ironwood, cypress, poplar, bamboo, plastic and other materials. Each of these wooden cutting boards has its own advantages and disadvantages. After using it, you will know its advantages and disadvantages.

No matter what kind of wood and bamboo cutting boards are still relatively healthy and safe. Natural materials are more trusted, but some of the high-quality plastic cutting boards that come out today are not only beautiful in appearance, but also very practical.

The camphor wood cutting board is hard and insect-free; Oak cutting boards are dense, non-absorbent, healthy and hygienic; The ironwood cutting board is hard and has a long service life; Poplar, cypress, bamboo** cheap, economical. The plastic cutting board looks beautiful and affordable. All kinds of wood cutting boards have their advantages, and it depends on your own choice which material to choose.

Wood quality requirements for solid wood cutting boards:

1. Strong texture, staggered texture, good split resistance, no lint, no slag;

2. The hardness is medium to high, but not too hard so as not to hurt the knife;

3. There is no abnormal smell or taste (bitter wood tastes bitter, Runnan smells smelly, oak wood tastes sour, and it is not suitable);

Fourth, long-term moisture does not decay, dry does not crack.

According to this quality requirement, the most suitable for cutting boards are: honey locust tree (soaphorn wood), clam wood, iron wood, beech wood (elm wood, not shell bucket wood);

Generally, those who can be used as cutting boards are: peach, osmanthus tree, elm, oak tree, mulberry tree, locust tree, black tree, soapberry, bayberry, willow, maple, banyan tree, etc.

Natural oak is better.

Moderate soft and hard, not easy to hurt the knife, not easy to deform, not easy to explode; No wood chips are produced when used; Moisture-proof and mildew-proof; Natural sterilization, easy to clean; Tough and heavy; The shape is simple, beautiful and generous, durable, and it is a rare kitchen helper to imitate the tomb.

The drill bit of drilling iron plate is generally a black drill bit, with a pointed tip in the middle, fine twist-like, and the teeth are relatively sharp, so the structure is more labor-saving, and the force is large when drilling, and the wear-resistant is conducive to feeding.

The material of the drill bit for drilling iron plate is generally cemented carbide, such as high-speed steel, which can be drilled on metal materials such as alloy steel, non-alloy steel, cast iron, etc., because of its high hardness, it is very wear-resistant, has a certain strength, and is suitable for high-speed cutting.

The drill wood is generally fine twist-shaped, the configuration is a three-pointed blade, there is a small tip in the center of the tip of the drill bit, the middle is high and the two sides are low, the equal angle on both sides is also relatively large, and even there is no angle, so that the drilling is faster, the cutting edge on both sides can also make the drill edge flush and beautiful, the woodworking drill bit does not have high requirements for the hardness of the tool, and the tool material is high-speed steel.

The drill bit for drilling the wall is generally a twist drill bit, the drill bit is the least sharp, the grain tooth is not sharp, the cutter bit is cemented carbide material, and the concrete and tile drill bit is with diamond.

<> difference: material, drill bit design structure and processing method and technology. In terms of material, the drill metal is generally black drill bit, and the drill bit material is generally high-speed steel.

Drilling holes in wooden materials, with the use of woodworking drill bits, woodworking drill bits cut sales are large, the hardness of the cutter is not high, and the cutter material is generally high-speed steel. In terms of drill bit design and structure, the drill iron is generally the middle tip, and the drill wood is generally a three-pointed edge. In terms of processing method, the iron is directly shoveled by the blade of the drill bit, and the drill bit of wood is drilled with two blades on the edge, which is cut off first by the flat edge in the middle.

Summary. Dear, hello, the new sticky board can be used directly but has not been treated to use the effect is good, the following provides you with a few suggestions, you can refer to.

Dear, hello, the new sticky board can be used directly but has not been treated to use the effect is good, the following provides you with a few suggestions, you can refer to.

Before using the newly bought cutting board, we must first wash both sides of the cutting board, scald it with boiling water, and wash off the layer of wax to make the hail tremble, this wax is to prevent the wood from drying out; After washing off, be sure to soak it in concentrated salt water for a day, which is to boil the water, add salt while it is hot, and add it until it no longer dissolves. The purpose of soaking in salt water for a day is to make the surface of the wood contain salt, which is moisture-absorbing and can prevent the wood from drying and cracking; After that, take it out to dry, and then evenly apply a layer of cooking oil on the surface of the cutting board, and it can be used normally after the oil completely penetrates into the cutting board, so that the purpose of the source is to make the cutting board not easy to crack and deform during use.