How to deal with the sweaty interior wall tiles, the wall moisture returns?

First, the waterproof layer of the external wall of the building is damaged, resulting in water seepage in the building. If this is the reason for the resurgence of the wall, it is necessary to contact the property or developer to carry out a comprehensive renovation of the waterproofing of the exterior wall of the building. Water seepage on the exterior walls of the building, especially after rain and snow, is a big problem that the owners cannot solve on their own.

The second is that the bathroom is not waterproof and the wall is wet. Generally, this situation often occurs when the bathroom is rebuilt with a light body wall. The bathroom must be waterproof, and the waterproof height must be 2 meters high, not only 30 cm high.

Otherwise, the moisture penetrates into the light wall through the tile and is absorbed by the light brick, which will penetrate the wall after a long time, causing the other wall that is not attached to the wall tile to produce damp and mildew. If this is the case, it must be re-waterproofed.

The third is that the daily splashing of water on the wall in the kitchen and bathroom causes the wall to be damp. This condition is one of the more common causes of wall moisture resurgence. This is especially more likely to happen on the wall under the kitchen cabinet and bathroom cabinet.

This is caused by splashes of water splashing along the kitchen cabinet wall when washing vegetables and dishes. It is recommended to use glass glue to fill the joints between kitchen cabinets, bath cabinets and walls to prevent water flow, and the phenomenon of wall moisture return can disappear.

Sweaty interior wall tiles and damp walls are caused by indoor air humidity.

To solve the sweating of interior wall tiles, it is necessary to start with the high moisture content of indoor air, and put a dehumidifier in the room where the moisture returns can eliminate the problem of moisture return on the wall.

1. Configure dehumidifier.

Newspapers can only solve the problem of water seepage on the ground and walls, but there is more moisture in the air, you can consider using dehumidifiers or dehumidification boxes to absorb them, and place them in all corners of the home and places with heavy moisture, which can effectively adsorb water vapor. In addition to all corners, putting one or two dehumidifiers in the wardrobe can also effectively prevent the clothes from getting wet.

2. Close doors and windows to prevent moisture from entering the room.

When the humidity hits, remember to close the windows in your home, especially those facing south and southeast. The most important periods of moisture protection are in the morning and evening, when the air humidity is higher than in the middle of the day.

Pay special attention to the bathroom door to prevent moisture from spreading to the rest of the room. After cooking or showering, remember to close the kitchen and toilet doors and turn on the exhaust fan to reduce moisture entering the living room.

3. Spread newspaper to absorb moisture.

It is also a good practice to spread newspapers on the floor and on the table to absorb moisture. Spread used newspapers on the floor and on the table, especially in places that are prone to wet, such as the doorway, and spread two more layers.

Change shoes at the door to avoid moisture from entering the house, and skillfully use dehumidifying items to absorb water.

In humid weather, the most important period of moisture-proof is the morning and evening of each day, the air humidity is the highest during these two periods, and the afternoon is the time of the day when the climate is relatively dry, we should briefly open the window for ventilation during this time period, so that the tiles can be exposed to the sun and breathable, accelerate the evaporation of water, so as to achieve the dehumidification effect. Tightly closed doors and windows not only do not play a role in preventing moisture, but are easy to breed bacteria and endanger the health of residents.

When cleaning, it is recommended to control the water consumption, avoid excessive humidity, and do not mop the floor directly with a wet mop. General stains with a soft dry rag can be, when encountering stains that must be cleaned with water, you can use hot water and salt to mop the floor, because the volatilization rate of the liquid is related to temperature, the higher the temperature, the faster the volatilization, magnesium chloride and calcium chloride in the salt have a certain water absorption, which is conducive to keeping the floor dry. Immediately after the mowing, open the doors and windows to allow air to circulate and dry the tiles.

Close doors and windows, try not to allow air circulation, and of course remember to breathe when sleeping.

It's best to keep windows and doors closed to prevent moisture from entering, and keep a dryer at home.

Moisture on the wall after tiling is a very common problem, and many people will encounter this situation during the construction process. If not treated in time, the damp wall will not only affect the pasting effect of the tiles, but also lead to problems such as cracking and falling of the tiles. So, how do we deal with this situation?

Solution:1Drainage system inspection.

First of all, you need to check the drainage system, because the cause of damp walls is most likely due to problems with the drainage system, such as leaking water pipes, rainwater entering the house, etc. If there is a problem with the drainage system, it needs to be repaired or replaced in time to ensure that water does not seep into the wall again.

2.Ventilation treatment.

Secondly, it is necessary to do a good job of ventilation to ensure that the air in the room is well ventilated and the wall can be dried as soon as possible. If there are no windows in the room, mechanical ventilation can be used, such as installing ventilation fans and exhaust pipes.

3.Moisture-proof treatment on the wall.

In response to the problem of dampness on the wall, He Ji can use methods of moisture-proof treatment on the wall, such as using moisture-proof agents, applying moisture-proof paint, etc. These methods can effectively prevent the wall from getting wet and improve the pasting effect of the tiles.

4.Tile treatment.

If the wall has been tiled, but there is a damp problem, it is necessary to remove the tiles in time and re-construct them. Before reconstruction, the wall needs to be thoroughly cleaned and dried to ensure that the wall is completely dry before construction.

All in all, the problem of dampness on the wall may have a great impact on the pasting effect of the tiles, so it is necessary to pay attention to many problems in the construction process, deal with the damp situation of the wall in time, and ensure the quality and reliability of the construction effect.

As an expert in construction and renovation, I have the following solutions to the problem of re-dampness of floor and wall tiles

1.Find out the cause of the dampness. First of all, it is necessary to find out the specific cause of the resurgence of bricks, whether it is the dampness of the bricks, the leakage of the interlayer, the seepage of water from the outside or the ventilation problem. Only by finding the cause can we solve the problem in a targeted manner.

2.Improve ventilation. Exhaust fans and air outlets are added to improve the ventilation environment on the surface of bricks. Accelerate the evaporation and dissipation of water on the surface and inside of the brick. This is the easiest and most economical way to control the resurgence of bricks.

3.Clean the mortar layer. Inspect the mortar or cement layer between bricks, remove damp or loose mortar, rebuild or repair the mortar layer. Blocks the passage of water seeping out of the middle layer.

4.Additional impermeable layers. For the resurgence caused by external water seepage, it is necessary to apply waterproof coatings such as PU or resin waterproof paint on the surface of the brick or the outside of the wall, or brush waterproof materials on the plastering surface of the wall to form a waterproof protective layer.

5.Inject glue or waterproof material. If the moisture return is serious, you can consider using grouting or magnetic suction to inject waterproof mortar or polyurethane waterproof material into the gap between the bricks to form an internal waterproof layer to avoid moisture infiltration.

6.Replace the bricks. For bricks with severe damp damage, if the above methods still cannot completely solve the problem, it is recommended to replace the bricks that have lost moisture. The method used by Sun Xiang is easy to cause damage to the brick surface, so it is not recommended.

7.Drainage facilities were added. Increase drainage pipes under the ground brick signal to strengthen the ground water discharge and avoid water accumulation between the bricks and the ground. This is particularly effective in solving the problem of resurgence of floor tiles.

Through the proper analysis of the causes of dampness and the formulation of targeted solutions, coupled with the necessary moisture prevention and drainage measures, most of the problems of moisture reflux of wall tiles and floor tiles can be satisfactorily solved. However, it is difficult to completely remove the existing damp traces inside the brick, which also needs to be considered in the treatment process. As a professional, I will provide more detailed solutions depending on the situation.

Moisture re-dampness of floor tiles or wall tiles refers to the appearance of water vapor or water droplets on the surface of floor tiles or wall tiles in a humid environment, giving people a damp and uncomfortable feeling. Here are some ways to cope:

1.Strengthen ventilation: First of all, it is necessary to strengthen ventilation to allow humid air to circulate and minimize the impact of humid environment on floor tiles or wall tiles.

2.Dehumidification: Dehumidifiers, desiccant, electric fans and other Mengqing limb equipment can be used to dehumidify the humid environment.

3.Check the water pipes: If the moisture return of the floor or wall tiles is caused by leaking or clogged water pipes, you need to repair the water pipes in time.

4.Check the waterproofing layer: If the re-moisture of the floor tiles or wall tiles is caused by the damage of the waterproofing layer, the waterproofing layer needs to be repaired or replaced in time.

5.Replacement of floor tiles or wall tiles: If the resurgence of floor tiles or wall tiles is severe and cannot be solved by the above methods, it may be necessary to replace the floor tiles or wall tiles.

It should be noted that the cause of the resurgence of floor tiles or wall tiles may be complex, and it is necessary to conduct a comprehensive analysis of the difference according to the actual situation and take corresponding measures. In addition, in order to avoid the occurrence of moisture re-dampness of floor tiles or wall tiles, it is necessary to keep the room ventilated and dry, clean up the humid environment such as the bathroom and kitchen in time, and regularly check the water pipes and waterproof layer.

Resurgence of moisture in floor and wall tiles can be caused by groundwater, damp environments, or structural problems. To solve the problem of re-moisture of floor tiles and wall tiles, you can try the following methods:

1.Prevent water sources: Make sure water sources are shut down and all pipes are tightly connected. If possible, turn off the empty faucets in bathrooms and kitchens during the wet season to prevent groundwater infiltration.

2.Strengthen ventilation: Open doors and windows to circulate indoor air and accelerate water evaporation. Using a fan or air purifier can help improve indoor air flow.

3.Use a dehumidifier or air conditioner: Use the dehumidification function of a dehumidifier or air conditioner to reduce indoor humidity. Please make sure that the device is set up correctly to avoid excessive dehumidification that can cause the wall to dry and crack.

4.Keep the floor dry: During the wet season, avoid mopping the floor directly on the floor or wall tiles. Use a mop with good water absorption to avoid water retention on the ground.

5.Use special protective agents for floor tiles and wall tiles: There are special protective agents for floor tiles and wall tiles on the market, which can prevent moisture penetration. Proper use according to the product instructions can effectively reduce the problem of moisture resurgence.

6.Laying moisture-proof materials on the surface of floor tiles and wall tiles: In areas with severe moisture, such as bathrooms and kitchens, materials such as moisture-proof mats and waterproof membranes can be laid on the ground to prevent moisture penetration.

7.Check the structure of the house: If the resurgence problem persists, it may be related to the structure of the house. Consult a professional for an assessment to find out what the problem is and take appropriate action.

8.Wall repair: When the wall has problems such as cracking and peeling due to moisture return, it should be repaired in time. After repair, apply anti-mold paint or repaint to prevent moisture re-emergence of the problem.

Please be careful to be safe when handling wet walls to avoid accidents such as electric shock or falls. Seek professional help if necessary.

The resurgence of moisture in floor tiles and wall tiles is caused by the presence of moisture on the wall or floor, and the moisture cannot be dissipated. In order to avoid the resurgence of moisture in floor tiles and wall tiles, you can take the following measures:

1.Maintain air circulation: Keep indoor air circulation, especially in the humid season, open windows every day for ventilation, so that indoor moisture can be discharged in time.

2.Indoor humidification: Place a humidifier indoors to increase indoor humidity and reduce the possibility of moisture return on floor tiles and wall tiles.

3.Regular cleaning: The surface of floor tiles and wall tiles should be cleaned frequently, especially in humid areas, and it is recommended to clean them once a week to avoid accumulating too much moisture.

4.Moisture-proof treatment: Treating a layer of moisture-proof paint on the surface of floor tiles and wall tiles can effectively reduce the intrusion of moisture. During construction or decoration, moisture-proof materials can also be added to the inside of the wall to prevent moisture from penetrating.

5.Avoid stacking items: Avoid stacking too many items on the surface of floor tiles and wall tiles in the front hall, especially wet clothes, towels, etc.

If the floor tiles and wall tiles have returned to moisture, the following treatment techniques can be taken:

1.Clean and dry: First of all, clean the surface of the floor tiles and wall tiles that are back to moisture, and try to dry the surface.

2.Air drying: Aim the fan with air circulation at the surface of the floor and wall tiles and let it air dry naturally, which can help the moisture to volatilize.

3.High-temperature drying: Use tools such as hair dryers or heat guns to dry the surface of floor tiles and wall tiles at high temperature to help moisture volatilize quickly, but avoid excessive drying to avoid cracking the brick surface.

4.Replace floor tiles and wall tiles: If the floor tiles and wall tiles have returned to the moisture seriously and the problem cannot be effectively solved after treatment, you need to consider replacing them with new floor tiles and wall tiles.

5.Find the source of moisture: In addition to dealing with the return of moisture on the surface of floor tiles and wall tiles, it is also necessary to find the source of moisture and deal with damp places in time, such as water leakage and water pipe leakage.

In short, the resurgence of floor tiles and wall tiles needs to be taken in time, and methods such as cleaning and drying, air drying, and high-temperature drying can be tried. At the same time, it is also necessary to find the source of moisture and deal with it in time to avoid the recurrence of moisture recurring.

Resurgence of floor tiles and wall tiles is usually caused by the infiltration of moist air or surface water. To solve this problem, the following measures can be taken:

1.Check and repair the source of the leak. First of all, it is necessary to check the joints or damages between the floor tiles and the wall tiles, find the source of water seepage or moisture, and repair them in time.

Then repair the surrounding cracked ditches, balcony ditches and other pipes or parts that may seep water. Cutting off water is the key to solving the problem of Jane Goh.

2.Install dehumidifying equipment. Install a dehumidifier or dehumidifier in the room where there is a return of moisture to enhance ventilation. Especially after water seepage repair, it is necessary to vigorously replace the humid air to reduce the humidity in the air to the normal range.

3.The surface of the table is waterproof. The treatment of spray waterproofing agent or elastic material on the wall and floor can effectively prevent external moisture from entering the bricks and brick joints, and achieve the effect of preventing moisture seepage.

Waterproofing materials also protect the surface of wall tiles from fading, notifying, and breakage.

4.Internally hydrophobic and moisture-resistant. If the moisture is returned from the basement or foundation, a moisture-proof membrane and a dehumidifying pipe can be installed in the wall to extract the moisture from the wall. It is also possible to carry out drainage works on foundations and basements to solve the problem of the source.

5.Always pay attention to ventilation. Even if the source of seepage water is cut off and moisture prevention measures are taken, it is necessary to strengthen constant monitoring and maintain good ventilation of the room at all times. Turn on the dehumidifier regularly to avoid excessive moisture accumulation.

6.The last resort is renovation. If the above methods fail to solve the problem, the wall tiles and floor tiles have been too deeply damp, for the comfort of the home environment, you can only choose the method of brick wall renovation and floor tile repaving to completely solve the problem of moisture return.

Comprehensive moisture-proof and dehumidification measures are taken to strictly cut off leakage water sources and ensure a good ventilation environment. Only then can the problem be hopefully resolved. The easiest and most economical way is to check your home regularly and fix it as soon as possible.