Is there any way to get rid of the shine from the iron?

If a bright glow has already occurred, cover it with a damp cloth and give it a quick and light scalding to make it disappear. Some woolen pants will also appear bright on the buttocks after wearing for a long time, which can also be eliminated by the above methods, such as spraying a small amount of acetic acid and then covering a damp cloth for ironing, the effect is better.

When you iron your pants, put a cushion between the iron and your pants to prevent your pants from being ironed with a shiny finish.

To remove creases on clothes or after the perm appears"Aurora", you can use a towel dipped in a small amount of vinegar to wipe the creases of the garment or"Aurora"place, it can be eliminated after ironing.

1. Sprinkle some fine salt immediately after scalding, then gently rub it with your hands, and then put it in the sun to dry for a while, wash it with water, and the bright marks can be reduced or even completely disappeared.

2. You can use a toothbrush dipped in cold water to gently scrub, and then take it to the sun to dry, which can reduce the bright color. Serious wool or cloth clothes, after washing with a toothbrush, and then using the hot gas when boiler water is boiled, the color weight becomes lighter, and the color is lighter.

3. Wet the bright part with cool water and expose it to the sun. When the water is dry, dust off some more water until it becomes similar to the color of the other parts.

The shiny surface of the fabric due to local friction or ironing during wearing is called the aurora phenomenon. Aurora is a phenomenon of light reflection caused by damage to the fibers on the surface of the fabric, especially on blue and black fabrics.

How can it be prevented?

1. It is best to iron the parts that are prone to aurora with a white pad cloth;

2. Control the temperature and pressure of steam, different fabrics have different withstand temperatures;

3. Don't rub too much in one place;

4. Maintain the flatness of the surface of the ironing table and iron.

If the aurora has already appeared, the damage to the cilia of the fabric is, in principle, irreversible. However, there are some ways to improve slightly, and you can also try the following:

1 Use a steam iron to apply steam to the aurora, then brush repeatedly with a soft-bristled brush;

2 Gently polish the aurora with extra-fine sandpaper, pay attention to the strength, and prevent it from backfiring.

Wash again, wash with warm water, wash with gold spinning, don't dehydrate, dry in the shade.

Then iron it the right way.

Sprinkle a thin layer of water on top of the clothes before ironing, then the temperature of the iron should not be too high, after ironing, hang to dry, and after drying, just whip the clothes with a towel that has been wrung out after soaking in hot water.

Scrub with detergent dipped in water.

Maintenance method: 1. The bottom plate of the electric iron is often due to improper temperature control during ironing, so that a layer of coke adheres to the surface, which should be removed in time, otherwise it will accumulate more and more, affecting the ironing effect.

2. You can use decontamination powder or cuttlefish bones dipped in some water to scrub, and do not use metal hard objects to scrape, so as not to scratch the electroplating layer.

3. When ironing is completed, remember that the iron is cooled naturally, and water should not be splashed to cool down.

4. After the use of the temperature-regulating electric iron, the temperature-regulating knob should be placed in the "off" or "cold" position to avoid the aging of the internal elastic metal parts due to long-term deformation.

5. For the steam jet electric iron, if you find that the water in the water level glass box is turbid or if you find that there is white powder falling in the exhaust hole, you can inject 50% of white vinegar and water into the water tank, heat it for a few minutes, and clean it. After washing and pouring out the vinegar, it should also be washed with water several times. When not in use, the steam button and steam injection button should be pointed to the "off" position to avoid spring deformation.

You can apply toothpaste and wipe it with a towel to remove it. Try not to use steel wool balls, it will scratch the iron and make it easier to get dirty.

Solution:

1. If it has just been ironed, you should immediately spray some fog-like splash on the clothes, then fold the clothes, open them after ten minutes, and the bright light will disappear.

2. You can also use a damp cloth to cover the bright place, and then iron it with an iron (but do not dry it), and the bright light will disappear.

3. You can also apply a mixture of half vinegar and half water in these places, apply it again after it is slightly dry, put a clean cloth on it, and then iron it to remove the bright light.

It seems to be a spray of vinegar. Then lightly brush with a soft-bristled brush. If not, you can take it to a dry cleaner or a tailor.

Answer 1: If the clothes are slightly shiny, you can spray some water on the burned place, adjust the steam ironing to medium temperature, put a layer of cotton cloth on it, and gently iron it to restore it to normal.

2. If the situation is more serious, use a small amount of talcum powder on the surface of the clothes, and after five minutes, adjust the iron to the steam temperature and iron it with a cloth through the clothes, and the clothes can be restored to their original appearance. (Note: When using steam, the iron should not directly touch the clothes, but should be a little away from the clothes, and spray the steam to the place where the mirror is raised, and directly restore it to normal).

Garment steamer Iron brush --- these 2 do not work, only eliminate small creases. If it's a deep fold, it's useless. In addition, the straight seams of the pants, the collar of the suit, the shirt collar, etc., must be ironed.

Therefore, it is recommended to buy a steam iron, which covers the other 2 functions.

Pick up the automatic sense of the encyclopedia