-
Carefully remove the graphics card and take it to the balcony to brush the dust first. You can use a small brush or a large oil brush to blow while brushing (it is best to have a "leather tiger" for blowing soot, or you can use a hair dryer to hit the cold air gear, or even use a pump to install a "gas needle" for playing basketball); Then add some oil. To apply oil, uncover the circular covering film in the middle of the fan, let the shaft be exposed, drip a little high-grade lubricating oil (do not use cooking oil, because the cooking oil will be sticky for a long time, affecting the operation of the fan), and then cover the film.
After brushing and oiling, the problem could not be solved, so it had to be replaced with a new one.
-
Shoe brushes, toothbrushes, or let the dog lick it, if you can't help it, the dog can lick it yourself.
-
Remove it and brush it slowly with a brush.。 The fan is relatively small. Be careful.
If it really doesn't work, go change it. This fan is relatively cheap.
-
The simpler way to do it without sending it for repair is:
Tools: A brush, a blow dryer (the kind you usually use to pump up basketball) Take the graphics card out of the motherboard, take it to a ventilated place, and if you don't mind, it's better to wear a mask.
Then use a brush to brush off the heavy dust on the surface.
Then use the brush to pat the fan to let the dust loosen inside.
Then use an air pump to blow off the dust on the PCB board and in the gap between the hot fan sheets.
When you put the motherboard back on, remember to wipe the gold finger clean.
-
How to clean the dust on the graphics card:
1. Separate the graphics card motherboard from the heat dissipation module and remove it with a screwdriver.
Unscrew the fixing screws between the graphics card and the cooling module.
2. After separating the heat dissipation module, you can use small parts to clean some internal corners of the graphics card.
3. When cleaning the dust channel of the graphics card, the most important part is the heat dissipation cleaning of the core chip, and carefully wipe it with an alcohol lint cloth.
4. The solidified silicone grease block on the copper bottom of the graphics card turbofan and radiator can be wiped vigorously with an alcohol flannel cloth.
5. The silicone grease block can be dotted with 4 corners and the center, and then slowly wiped in one direction.
6. Finally, clean up the graphics card screws and screw them back, and install them back in the original way, that is, the cleaning is over.
-
First of all, remove the fixing screws of the graphics card and the host, and then you can remove it from the computer motherboard, here is a simple talk about the need to use some tools to clean up the graphics card, generally cleaning the graphics card needs to be used: screwdriver, silicone, cotton swabs, hair dryers, etc., these gadgets that we don't have, can be purchased online, ** are not expensive.
1. First of all, you need to separate the graphics card motherboard from the heat dissipation module, and here you need to disassemble the fixing screws of the graphics card and the heat dissipation module.
2. After disassembling and separating the motherboard and heat dissipation module of the graphics card, we can see that a large amount of dust will accumulate inside the graphics card with a turbo air duct, and at this time, a small cotton swab will come in handy to clean up some internal corners.
3. In addition, a large amount of dust will accumulate on the graphics card PCB board, especially in places such as air outlets, which is the most serious, we can use a cotton swab to clean it up simply, and it is best to dip some alcohol on the cotton swab to clean it up.
4. When cleaning the dust of the graphics card, the most important part is the heat dissipation cleaning of the core chip.
5. The graphics card turbofan is also wiped clean by the way, and the solidified silicone grease block on the copper bottom of the radiator is also wiped down, which can be used harder.
For friends with conditions, you can also use a high-power fan or a dust washer to clean the dust on the surface of the graphics card, or you can use a hair dryer to help clean up the dust.
-
Here's how to clean it up correctly:
1. Remove the graphics card from the main version of the computer and miss the beam. And put it on a softer place.
2. Remove all the screws on the graphics card with a ten-scum word knife. At this time, be careful to break the fan wire.
3. Carefully remove the fan, and at the same time you can throw the heatsink into the water to wash it, remember that the fan should not enter the water.
-
If you've never replaced a computer accessory or opened a case, you're bound to be intimidated by the mountains of dust that pile up inside your computer. First, place the computer on the balcony or in an open environment, open the panels on both sides of the case, and take out the components in the case one by one. Dust is mainly concentrated in active cooling devices with fans such as CPU coolers, graphics card coolers, and power supplies.
Tools: a flat-mouthed and ten-mouth screwdriver, a cotton swab (toothpick is also acceptable), a blade, engine oil (preferably for sewing machine oil), waste film negatives, scissors, 502 glue, a small row of brushes (the kind with a width of 2cm), a hair dryer or a leather tiger.
Disassembly and cleaning method:
1. Graphics card fan series:
This type of fan is generally built-in. That is, it is fixed in the heat sink of the graphics card by screws or other devices. So there is nothing to pay special attention to when unloading.
Use a brush to clean the dust on the surface of the fan and the heat sink, and use a cotton swab to clean the dead corners. Be careful not to push too hard.
2. CPU fan series:
Generally, the heat sink of the AMD series is of the seizure type. So, here's a tip, don't remove the fan when you haven't removed the whole thing (as we all know, the little things on the CPU can't stand the load).
Use a flat-blade screwdriver to press down on the fastener (with a slight force inward) to exit the fastener from the bayonet of the CPU base. Then the whole can be removed from the CPU.
As for the heat sink of the Intel series, it is generally only a double fastener type. So, it's easy to remove.
Use a cross-hatch screwdriver to remove the fan from the base (at this point, you may marvel at the dust inside your heatsink) and then use a brush to clean the fan pages. The heatsink can be rinsed with running water (if you find it troublesome to clean it with a brush), and remember to air dry before installing the CPU.
-
Remove the graphics card and use a hair dryer to blow (cold air), preferably with a pump!
-
The computer CPU fan has too much dust, which seriously affects the use, teach you how to dust the computer.
Teach you how to clean an electric fan.
You need to go to the computer *** to hand over to the after-sales cleaning, and there will be some trouble in cleaning it yourself >>>More
360 Security Guard has all kinds of garbage in the computer. You can go and try it.
1. The memory is the largest when you first turn it on, so generally rebooting it can reach the maximum memory in the existing state of the phone. >>>More
into my computer. Then click on the C drive, then select Properties, and you will see a disk cleanup button. It's a good idea to turn off all programs before cleaning up here.