-
Simple, and then according to the calibrated horizontal line, it is good to make a flat frame on the ground with a wooden keel or stainless steel or plastic wood keel. Hope it helps. If there is underfloor heating, it is OK to add underfloor heating pipes to the frame, first you find out the level of the room.
-
If your plumbing is heated by radiators, there are only a few plumbing pipes, as long as the location of the pipe is marked and the keel is avoided at that time, if it is heated by the plumbing pipe, the keel on the wooden floor will seriously affect the heat!
-
Pavement: Solid wood long tongue and groove flooring, the biggest difference between it and the general short floor plate and composite floor is that the "stepping feeling" of the floor is strong. In order to ensure the "sense of stepping", so the pavement is very important, both smooth and seamless, and three aspects must be paid attention to when paving:
Selection of materials for joists. The joists should choose pine with strong nail holding power, such as green pine, Douglas fir, Masson pine and larch. Do not choose materials with weak nail grip.
Fixing of joists. Generally, the joists can be fixed on the floor with expansion bolts and horizontal angles after planing. Some construction teams like to use cement next to the joist, such as using cement to cushion the bottom, must wait for the cement to dry before paving, otherwise it will cause the floor to swell and arch.
Floor tiling. It is best to use special floor nails with a spiral shape (sold in decoration stores) when the floor is tiled and fixed on the joist, and at the same time, the grooves between each board must be tightened, otherwise the natural stress of the floor will be destroyed and the floor will easily crack. The climate in Shanghai is characterized by four distinct seasons and high humidity, so expansion joints should be naturally left around the floor to adapt to the changes of thermal expansion and cold contraction of the floor.
Maintenance of flooring: There is a maintenance problem for any items and utensils, as the saying goes, "seven points of beauty and three points of nourishment."
-
Hello dear! Can I put a wooden floor directly on top of the underfloor heating? Yes, you can.
Wood flooring can be installed, but there are requirements for the performance of wood flooring, wood flooring must have good thermal conductivity, high thermal stability, water absorption rate can not be lower, so as to avoid the use of floor heating, wood floor thermal expansion and contraction, resulting in deformation of wood floor and other problems.
Second, the requirements of floor heating for wooden floors.
1.Material requirements.
Not all wood floors are suitable for floor heating, and the selection of floor heating wood floors meets many conditions, such as whether the size of the wood floor is temperature, whether the heat transfer is good, and the water absorption rate of the wood floor can not be exceeded.
2.Stability requirements.
Because the stability of the wooden floor is not very good, it is easy to have thermal expansion and contraction, resulting in deformation and other problems of the wooden floor, so many wooden floors are not suitable for laying floor heating, and only the wood floor with good thermal stability is more suitable for laying floor heating.
3.Waterproof and mildew-proof requirements.
Generally, the waterproof and mildew-proof performance of the wooden floor is relatively poor, as long as it is stained with water, if it is not treated in time, it will lead to mold, cracking, warping and other problems on the wooden floor, which not only affects the appearance, but also affects the use of floor heating, which is very unsafe.
-
Summary. Hello! Installation of underfloor heating, how to lay wooden floors method:
It adopts a hanging installation method. The flooring material needs to be padded to get close to the ground. Therefore, there is no gap between the floor and the ground, and there is a large shrinkage gap between the floor.
Due to the large amount of moisture released by hydrothermal radiant heating, efforts must be made to prevent moisture from causing mold on the floor. Please click to enter ** to describe that when paving, clean the ground first, pay attention to the corners and make sure there are enough expansion joints. Floor mats need to be laid.
Care is taken to reserve expansion joints, the interface is at least 5 cm, and must be sealed with adhesive tape. At the same time, the use of baseboards that are thicker than ordinary floors requires construction. Flooring can only be preheated 24 hours after installation.
To promote heat conduction, the liner material should not be too thick.
Installation of underfloor heating, how to lay wooden floors?
Hello! I am this Zhengchen time for you to solve the confusion of filial piety Zen friends, please wait a while, I am sorting out the answer! We hope you understand! Thank you! ☺️
Hello! Installation of underfloor heating, how to lay wooden floors: use a hanging installation method.
The flooring material needs to be padded to get close to the ground. Therefore, there is no gap between the floor and the ground, and there is a large shrinkage gap between the floor. The amount of moisture released by the heating of the water heat radiation is very large, so efforts must be made to prevent moisture from causing mold on the floor.
Please click to enter ** to describe that when paving, clean the ground first, pay attention to the corners and make sure there are enough expansion joints. Floor mats need to be laid. Care is taken to reserve expansion joints, the interface is at least 5 cm, and must be sealed with adhesive tape.
At the same time, the use of baseboards that are thicker than ordinary slag majen floors requires construction. The floor can only be preheated 24 hours after installation. To promote heat conduction, the liner material should not be too thick.
It is possible to install a solid wood snap-on geothermal heating floor, which overcomes the shortcomings of the cracking, arching and other shortcomings of the solid wood floor, and uses the expansion and contraction of the spring to leave a certain amount of expansion joints to adjust the expansion and contraction of the solid wood floor. Because there are small seams, it is not easy to deform when it swells. In order to increase thermal conductivity, the thickness of the cushion and floor should not be too thick, and after the installation is completed, keep the ground clean before heating up, and gradually heat up.
If the first bush is used or has not been opened for a long time, set the minimum temperature first and slowly increase the temperature to make the wooden floor gradually seep into the wood.
-
1. Before installation, check whether the sand content of the geothermal ground is too large and dry, and if there is too much gravel, gypsum should be smoothed, and the moisture content of the ground should be reduced to below. It is best to send the wooden floor to the installation place 48 hours in advance to adapt to the temperature of the floor heating to prevent the temperature from rising quickly and cracking and twisting.
2. During installation, it is strictly forbidden to nail and punch holes on the ground to prevent damage to the floor heating coil; During the laying process of wooden flooring, there should be sufficient expansion joints between the walls and door posts. The paving of the ground and the installation of the baseboard should be carried out in two phases. 48 hours after laying the floor, wait for the glue to dry completely, remove the fastener and then make the baseboard.
3. After the installation is completed, the temperature will gradually rise after 24 hours, and the first time you use geothermal heating, you should also pay attention to the slow heating. When used for the first time, the first three days of heating should be gradually heated, and the temperature should not be too fast to avoid cracking and twisting of the floor due to expansion, which will affect the service life of the wooden floor.
-
The method of laying underfloor heating wood flooring is very important, because improper laying will affect the effect of floor heating and the service life of wood flooring. Here are some ways to lay underfloor heating wood floors.
1.Tool preparation: The tools needed to lay the floor heating wood floor include hand saws, hammers, nails, rulers, ink lines, and floor installation tools.
2.Wiring first: Before laying the floor heating wood floor, you need to wire first, lay the floor heating pipeline, and use the ink line to determine the edge line of the floor.
3.Installation of flooring: The installation of underfloor heating wood flooring requires laying aluminum foil insulation film under the underfloor heating pipes, and at the same time shortening the length of the floor to ensure that the length of the floor is consistent with the length of the room.
4.Nailing the wooden floor: Use a hand saw to see off the flange part of the joint, remove the burrs of the floor, ensure that it is flat when laying, and then use the floor nails to fix the floor to the ground.
5.Seam treatment: There needs to be some expansion joints between the wooden floors, so it is necessary to leave a gap of 1 to 2 mm at both ends of the floor.
6.Sandpaper treatment: Use sandpaper to polish the wooden floor to ensure that the surface is smooth and free of defects.
7.Maintenance oil: After the laying is completed, it is necessary to use the maintenance oil on the wooden floor to ensure the beauty and durability of the wooden floor.
In short, laying floor heating wood floors needs to be carried out carefully and meticulously, laying floor heating pipes, aluminum foil insulation film and other materials on the ground to ensure that the ground is flat and judge the pure pants and thermal insulation effect, and then install the wooden floors one by one according to the ink line. During the installation process, it is necessary to pay attention to the nailing and seam treatment of the wooden floor, and the pants to ensure the firmness and beauty of the floor. After the laying is completed, use sandpaper to polish the surface and apply maintenance oil for maintenance, so that the floor heating wood floor can have a better use effect.
1. The pavement scheme should be constant.
For each stadium, or theater stage, what materials to pave, and how to pave, are determined according to the actual parameters of the sports venue and the investment budget. Therefore, once the sports wood floor paving scheme is decided, it should not be changed easily. >>>More
In contrast, it will be better to lay tiles, the tiles heat faster, if it is floor heating, then it will make the whole house very warm, and the tiles are more wear-resistant.
Personally, it is recommended to paste tiles better, not afraid of water, not afraid of cold and heat, easy to take care of, of course, wooden flooring also has its advantages, this thing depends on your actual needs, it can only be said that the floor heating has been inspected for a long time.
The most important thing depends on your choice, I will only help you analyze, first, in terms of usability, the floor tiles will be used for a long time, however, psychologically, the floor tiles will feel cold. Wooden floors, over time, the floor will be deformed, and it will cost a lot of money to renovate. It takes time, effort and money, but the wooden floor will be very classy. >>>More
Personally, I think that a house with underfloor heating should be tiled; I think that the house with floor heating needs to be installed, if the wooden floor is laid, it may cause the wooden floor to deform and crack after a long time.