How to load and unload the rear seats of the Leiling manual elite version

The tutorial of removing the rear seat of Leiling Shuangqing is as follows:

1. Pry the battery cooling fan ventilation filter from the left edge to the right and remove the filter. If you do not remove the filter first, directly lifting the seat cushion will damage the plastic ventilation duct under the seat, or make the ventilation duct fixing buckle shattered, and the fragments will fall under the car, causing abnormal noise or damaging the circuit, and the contact with the high-heat exhaust pipe will also produce a plastic burnt smell, increasing the risk of vehicle fire, so you must be very careful.

2. Lift the front of the seat hard, there is 1 buckle on the left and right, just lift it up to trip, the new car is relatively tight, you can try to shake it slightly to make it easy to remove, add a trace amount of car wax or lubricating oil to the buckle after removing, which is convenient for restoration and installation or remove the base again later.

3. There are three 12 bolts on the left, middle and right sides of the seat backrest, unscrew them counterclockwise, and put them for later use.

4. Carefully take out the seat belt from the gap in the upper buckle and stretch it to facilitate the removal of the backrest.

5. Vigorously lift up and remove the lower backrest, you can slightly lift up to loosen the buckle, a total of three buckles on the upper part of the backrest.

6. Put on the seat cover; The cause of rust on the bolts is speculated to be that the battery is hot, and the moisture in the air will condense on the part of the battery shell that cools down first, and it is also speculated that a small amount of electrolyte will also precipitate due to thermal expansion and cold contraction, which will aggravate the corrosion. It is hoped that the manufacturer will upgrade the anti-rust measures in this part of the successor products.

Rear seat cushion removed:

1.Open the rear door, and in about this position, lift the seat cushion slightly, and touch it with your hand, and you will feel something like a buckle.

2.Reach the buckle position with both hands, step into the car with one foot (convenient for force), and then lift the cushion up with both hands, not twice, it is best not to continue to force to prevent breaking. The cushion is pulled out after getting up. The rear seat cushion can be removed.

Hello, there is a clip under the seat, just pull it up, the landlord can make a reference.

How do you remove the back seat of the elite version?

Summary. Hello The method of folding the rear seat of Lei Ling is: 1. Two buckles of different colors can be found on both sides of the rear seats of the vehicle, and the buckles are used to fix the switch of the rear seats; 2. Press and hold the buckle with both hands at the same time, and pull down the rear seat at the same time.

Hello The method of folding the seats of the rear dismantler row of Leiling is: 1. On both sides of the rear seats of the vehicle, you can find two buckles of the same color and limbs, and the buckles are used to fix the switch of the rear seats; 2. Press and hold the buckle with both hands at the same time, and pull down the rear seat when the same Zen Yushi.

1 Lei Ling is a one-liter banquet compact sedan model, its body dimensions are 4640mm long, 1780mm wide, 1455mm high, and the wheelbase is 2700mm. The Lelink is equipped with a direct-injection turbocharged pure motor, with a maximum torque of 142 Nm and a maximum torque of 4,000 rpm.

2. The driver's seat seat adjustment button is located on the left side of the seat cushion, which mainly has the functions of lumbar support, seat position and backrest. The rear seat of the Toyota Levin can be folded down with a shoulder switch.

3 The new generation of Lelink has two power versions, the gasoline version is equipped with the D-4T direct injection turbocharged engine, the engine can output a maximum torque of 185Nm at 1500 rpm, and can be matched with a 10-speed S-CVT continuously variable transmission. The new generation of Lelink Shuangqing model is equipped with Toyota's latest THS II hybrid system, equipped with an Atkinson inline four-cylinder engine designed for hybrid systems, with a fuel consumption of only 100 kilometers under comprehensive working conditions, and is matched with an E-CVT electronic continuously variable transmission.

When the rear seats of this car are disassembled, the seat cushion needs to be removed first, and then there are fixing screws on both sides, and after the screws are removed, you can remove them by pushing them up. Toyota Levin rear seat reclining can be modified to recline ratio 2 proportional reclining.

Toyota Levin rear seat reclining can be modified to recline ratio 2 proportional reclining. 1/3：

2 3 Proportional Reclining: Generally appears in the back row with three seats, and can be reclined for two seats on one side or one seat on the other side. 1 2 proportions down down:

It usually appears in the back row with two seats, and one of the two seats can be folded down.

It can also be modified to fold the rear seat as a whole, and the rear seat is reclined as a whole, and when a large object needs more space, the rear seat backrest can be folded down to obtain more space. The disadvantage of the rear seat being folded down as a whole is that when the rear seat is folded down, the rear seat cannot be occupied.

Proportional reclining of the rear seats means that the backrest of the rear seats can be reclined proportionally, which is more flexible than the overall reclining of the rear seats, and can only fold down half of the backrest to place large items, while the part that is not reclined can still sit people.

Steps to remove the rear seats of the new 2019 Leiling:

1. Pry the battery cooling fan ventilation filter from the left edge to the right and remove the filter. If you do not remove the filter first, directly lifting the seat cushion will damage the plastic ventilation duct under the seat, or make the ventilation duct fixing buckle shattered, and the fragments will fall under the car, causing abnormal noise or damaging the circuit, and the contact with the high-heat exhaust pipe will also produce a plastic burnt smell, increasing the risk of vehicle fire, so you must be very careful.

2. Lift the front of the seat hard, there is 1 buckle on the left and right, just lift it up to trip, the new car is relatively tight, you can try to shake it slightly to make it easy to remove, add a trace amount of car wax or lubricating oil to the buckle after removing, which is convenient for restoration and installation or remove the base again later.

3. There are three 12 bolts on the left, middle and right sides of the seat backrest, unscrew them counterclockwise, and put them for later use.

4. Carefully take out the seat belt from the gap in the upper buckle and stretch it to facilitate the removal of the backrest.

5. Vigorously lift up and remove the lower backrest, you can slightly lift up to loosen the buckle, a total of three buckles on the upper part of the backrest.

6. Put on the seat cover; The cause of rust on the bolts is speculated to be that the battery is hot, and the moisture in the air will condense on the part of the battery shell that cools down first, and it is also speculated that a small amount of electrolyte will also precipitate due to thermal expansion and cold contraction, which will aggravate the corrosion. It is hoped that the manufacturer will upgrade the anti-rust measures in this part of the successor products.

The rear seats of this car need to be removed when disassembling the seat cushions, and then there are fixing screws on both sides, and after the screws are removed, they can be removed by pushing them upwards, and they can also be modified into the rear seats as a whole, and the rear seats are reclined as a whole.

The rear seats of the Leiling can be folded down with a shoulder switch. First of all, you can find two buckles of different colors on both sides of the rear seats of the vehicle, and the buckles are used to fix the switches of the rear seats. Press and hold the buckle with both hands at the same time and pull down on the rear seat at the same time to lay the seat flat.

Once the seat is flat, unfasten the seat belt buckle on the seat so that the seat is flat.

The seat adjustment button of the Leiling driver's seat is located on the left side of the cushion, which mainly has three adjustment functions: lumbar support, seat position and backrest.

1. Leiling front seat adjustment (electric seat) 1. Press the lumbar support switch to adjust the seat angle of the lumbar position; 2. Lift up and down the cushion adjustment switch, which can be raised and lowered to reduce the height of the cushion. The forward and backward moving switch can realize the forward and backward movement of the seat; 3. Push forward: the backrest is tilted forward; Move back:

The backrest is tilted back.

2. Leiling front seat adjustment (manual seat) 1. When you need to adjust the seat backrest, you can pull the backrest switch.

2. Height adjustment switch: This switch can control the height of the seat, pull up to become high, and press down to become low.

3. Forward and backward position adjustment: When you want to adjust the front and rear position of the seat, you only need to pull the bow under the seat.

Photo by Q&A) NIO ES8 NIO ES6 Wenjie M5 NIO EC6 Xpeng P7 Trumpchi GS8 @2019

Leiling rear seat disassembly: When the rear seat of the car is disassembled, the seat cushion needs to be removed first, and then there are fixing screws on both sides. Once the screws are removed, you can push them up and remove them.

The backward tilt of the rear fluid escort row seats of the Lelink Toyota can be converted into a backward tilt ratio of 3 and 1:2 3 ratio downward: usually chaotic appears in the rear three seats.

It can also be converted into a single rear seat, which means that the backrest of the rear seat is a unit. When you need a large amount of empty space to pull up a larger object, the rear seat backs can be folded down to create a larger amount of empty space. The disadvantage of the rear seats being folded down as a whole is that the rear seats cannot be occupied when the rear seats are folded down.

The proportional reduction of the rear spine seats means that the rear seat backrest can be lowered proportionally. Compared to the overall reduction of the rear seats, the proportional reduction is more flexible, with only half of the backrest being lowered to accommodate large items, while the unlowered part can still be used by people.

Millions of car purchase subsidies.