Is seamless brick better? Is the quality of seamless tiles good? How to choose?

In the long road of life, people must always have loose and tight, otherwise there will be a lot of problems in the later stage, and the same is true for tile paving, otherwise in daily life will inevitably encounter problems such as tile hollowing, cracking, and falling off.

Seamless sticking method is only relatively speaking, there is a seam, so seamless is when sticking bricks, do not add a cross locator, the range of adjustment is within millimeters, if the brick surface itself is flat, you can paste it directly, no longer add a cross locator, if the weak deviation, you can use the toothpick borrowing method to adjust. To borrow a technical term for tiling. But the toothpick borrowing method is not used toothpicks, but can be thinner than toothpicks, such as the thickness of the discarded steel tape measure, etc., this is more accurate than the toothpick, the seam sticking method is to use the cross locator to locate the size of the seam, the general cross locator has etc., the paste method of the seam has a three-dimensional effect, the concave and convex sense is very strong, but the amount of caulk will also increase a lot more than the seamless brick, and it may be doubled.

There is no seamless tile in the tile itself, because the tile itself will have a cooling process after firing, resulting in a slight warping of the tile, or there are problems such as slight size errors, so the tile needs to be adjusted through a suitable gap in the paving process.

For the decoration effect, the seamless paving of ceramic tiles will be more beautiful, so some people will choose to carry out seamless paving, or adjust the tile problem through small gaps, so that the surface will not have a large sense of gaps visually. It may work well, but it will have some impact in daily life.

As mentioned above, tile paving can not be seamlessly paved because it needs to be adjusted, and if the gap is too small, it will not be able to deal with the dust and dirt in the gap that falls later.

Moreover, different ceramic tile materials and properties are also different, so the size of the gap that may be reserved in the process of tiles in the paving process will also be different, which should be treated according to the specific situation.

Seamless tiles are not good, because leaving a little gap is very good for tiles, which can prolong the life of the tiles.

Seamless bricks will indeed be better, because overall it will be more beautiful, but ** will be higher.

It will indeed be better, and it will be more beautiful, and the most important thing is that it will be particularly strong during use.

I think it's really better, this kind of brick is more convenient to use, and it is more beautiful.

Seamless splicing floor tiles are particularly fashionable in the first two years, and they are the direction of the fashion of floor tilesMajor brands have launched different styles of seamless splicing floor tiles, but seamless splicing floor tiles are not fashionable for two or three years to be eliminated by the sales market, the most important factor in this is due to the seamless splicing floor tile parquet after the completion of the use of the porcelain bulge after the heat expansion and contraction, seamless splicing floor tile parquet without leaving a seam to suffer from heat expansion and cold contraction will go out product quality problems, so it can not withstand the tempering of the sales market, in the market only a temporary stay on the elimination of the future, gone forever.

Seamless splicing floor tiles are more comprehensive than jointed floor tiles, with good decorative effect, and in ordinary daily life, there will be no dirt in the middle of the floor tiles, which is conducive to cleaning in the future, but the master followed the next-door neighbor to see a circle, and he paid attention to the problems of the next-door neighbor in the middle and late stages, whether it is to lay wall tiles or floor tiles, or propose to pave jointed floor tiles. Jointed floor tiles are more conducive to engineering construction, and the cost of engineering construction is saved, while the technical standard of seamless splicing floor tiles is higher, once it is not paved.

It is very easy to crack and hollow the wall, causing unnecessary inconvenience to residents in the middle and late stages. There is a gap, and after the floor tiles are deformed, the gap will be squeezed. In this way, if you have a gap for buffering, it is not easy to paste the floor tiles to cause threat, and it will not spread to other wall tiles.

When decorating the living room, many people like to pave tiles, and there are many advantages of floor tiles, especially in the northern region, where most of them are underfloor heating, which creates resource advantages for tiles.

Floor tiles not only have high thermal conductivity, but also are fashionable and trendy decorative designs. Suitable for a variety of decoration styles, new house decoration, this is why many people like to pave tiles in the large living room, are a kind of information that is more fashionable at present. There are no seams left in the floor tilesIt can also cause hollowing of the wall, but hollowing of the wall is also a key cause of tile peeling.

The quality of seamless tiles is not very good; When choosing, you should choose a better material tile, generally speaking, seamless tile thermal expansion and contraction is more serious, and the adhesion on the back will be particularly poor, the more expensive the tile, the better, if the budget is not enough, but also choose the best tile in the budget.

Yes, the quality of seamless tiles is indeed better, such tiles are better integrated, so that the coordination of the whole space is also better, which can improve the interior aesthetics and make the whole space more atmospheric and high-grade; When choosing tiles, it is necessary to choose the appropriate color according to the interior decoration layout and personal favorite style.

Not good, it is easy to collapse when it expands and shrinks, and it is necessary to look at its hardness and slip resistance when choosing tiles.

1. Seamless tiles are generally large-size tiles, such as *1000, etc., due to the large size, the number of tiles used is small, plus the use of none.

The sewing process caters to the modern consumer fashion, and the decorative effect of the product paving is much more beautiful than that of the seam brick.

2. Seamless bricks have relatively high requirements for construction technology, pay attention to paving and smoothing, adjust the joints up and down, and it is difficult for masons who generally do not often pave seamless bricks.

3. The specifications of jointed bricks are smaller, such as *330, etc. The construction of jointed bricks is not difficult, and it is relatively easy to pave, but the decorative effect is average.

4. The choice of seamless and seamed tiles should be decided according to personal preferences and the size of the house space, and the size of the tiles purchased should be matched with the space of the house to be decorated, so that they can.

Get a beautiful and harmonious decoration effect. Otherwise, blindly pursuing large or small tiles will often leave yourself with regrets.

Whether it is a seam or a seamless brick, it must be operated in strict accordance with the regular process during construction, especially the expansion joint between the bricks and bricks should be left 1-, so as to adapt to the shrinkage prestress of ceramic products and prevent the construction quality problems such as cracking and deglazing of the brick body caused by no joints.

This is a wrong understanding, the so-called seamless brick is just a delicate point on the brick treatment process, between the brick and the brick through the process to cover the gap, no matter what brick you are, even if it is the best brick, when the worker sticks to the wall, there must be a certain gap between the brick and the brick, because the brick has the principle of thermal expansion and cold contraction, otherwise, the wall tiles will be seriously deformed and damaged after expansion. This kind of deformation caused by tiling, the manufacturer will never make a claim, and will laugh at you for not even knowing the basic common sense.

The size of the seamless brick joints should generally be around 1. You can use the cross as a reference (you can ask the brick seller to deliver it).

Hope it helps.

The floor tiles can not be seamed, otherwise they will be arched and deformed due to thermal expansion and contraction.

First, the tile gap is easy to get dirty and can be treated like this:

1. Prepare the tile caulk, pay attention to its color as close as possible to the color of the tile, and the other main tool is the silicone gun.

2. If you want to put the caulk into the silicone gun, first press the upper end of the silicone gun and press it, and then pull the lever up to the top, so that you can put the caulk into the silicone gun.

3. Before caulking the tiles, the gaps of the tiles should be cleaned, and the dust should be swept away with a brush as much as possible, and there should be no water in the gaps.

4. Fill along the gap of the tile, extrude the caulk while moving, and try to make the caulk evenly fill the gap in a continuous straight line.

5. Put on the finger sleeve and slide your finger along the extruded caulk to make the gap filled and smooth.

6. Wait for about a minute, and then you can easily scrape away the extruded remaining material with a blade.

The caulk will solidify after an hour, and it will be completely solidified and hardened after 24 hours, which will not affect the mopping of the floor, and it will not be difficult to wipe it off due to dust entering in the future.

It is best to leave joints on the floor tiles, because you yourself say that the heat rises and shrinks, and if you don't leave seams, the tiles will bulge. You can use caulk to caulk, if you use cement, it will dry out and crack over time.

Any object has thermal expansion and contraction, so seamless paving is basically impossible. Now the most mature and achievable is the dense seam paving, which is to reduce the traditional gap of about 3-5mm to less than, which greatly increases the overall visual effect. The requirements for the product will be more demanding, and Jane has its own standard process of seam paving, which is mainly to avoid the problem of thermal expansion and cold contraction

The first is that the adhesive layer replaces the cement slurry with Jianyi's proprietary binder, which is an exclusive excipient jointly developed by Jianyi, the Italian Carotier company and Baoqingti, and the shrinkage rate is 70% lower than that of the cement slurry; The second is to reserve 1-2cm expansion joints around the corners of the wall to give enough space for expansion and heat dissipation.

What is the difference between seamless brick and caulked brick? Do seamless wall tiles need to leave joints?

1.The difference between seamless bricks and jointed bricks is that seamless bricks are mostly large-size tiles, and seamless wall tiles need to be jointed. Due to its larger size, the number of tiles used is comparatively smaller.

In addition, it uses seamless technology that caters to modern consumer fashions. Therefore, the decorative effect of the laid product is more beautiful than that of the spliced tiles. However, the size of the grout brick is small, the construction difficulty is not large, and it is easy to pave, but the decorative effect is average.

Seamless bricks have high requirements for construction technology, and pay attention to the flatness of paving. It is difficult for bricklayers who do not often lay seamless bricks to do so. The construction of tile joints is not difficult, and it is easy to pave, but the decorative effect is average.

The choice of seamless and seamed tiles should be decided based on personal preference and the size of the space in the house. The size of the purchased tiles should match the space of the house to be renovated as much as possible for an aesthetically pleasing and harmonious decoration effect.

2.You must know that any object has the characteristics of "thermal expansion and cold contraction", and cement and ceramic tiles are no exception. Moreover, the expansion and shrinkage rate is inconsistent, and the tiling is laid completely seamlessly, and there may be "hollowing" during use, which directly leads to fracture (especially where hot water pipes are laid).

Because there are deviations in length, right angles, straightness of the edges, etc. There is no mistake in these respects that the tile does not exist. There will be some errors in tile construction.

Mechanized products will have errors, not to mention the manual operation of pavement workers, which is unavoidable. It should also be combined with the decorative effect of tile paving.

3.Generally, seamless brick tiles are large specifications, such as 300*450, 330*600, 360*660, 600*900, 660*1000, etc. Due to their large size, the small number of tiles used, and the seamless craftsmanship caters to modern consumer fashion.

The decorative effect of the paved products is much more beautiful than that of tiles. Seamless bricks have high requirements for construction technology, and pay attention to the flatness of paving. It is difficult for bricklayers who do not often lay seamless bricks to do so.

The size of the jointed brick is smaller, such as *330, etc. The construction of grout bricks is not difficult, but it is easy to lay, but the decorative effect is average.

Seamless bricks look more beautiful, and the integrity is better, more beautiful, but the jointed brick is easier to maintain and replace, and the disadvantage is that it is easy to warp; Seamless wall tiles also need to leave joints, because we need to prevent the thermal expansion and contraction of the bricks to avoid tile damage.

The effect is different, the appearance is different, the process requirements are different, the cost is different, and the applicable situation is different; Of course, there needs to be a seam.

The specifications of the two are different, the process is different, the flatness of the laying is different, and the size is different; In fact, seamless wall tiles also need to be seamed, but the joints should not be too large, so that they can be applied with a seam agent without affecting the appearance.

Jointed bricks are two bricks put together with an obvious gap, the most common is the matte brick of Marco Polo tiles, the brick edge is a hypotenuse. Moreover, there are large seams with seams pasted with bricks, obvious lines, and three-dimensional effect. The seamless brick is basically a very thin thread when the two bricks are put together, and the seam is small and not easy to get dirty.

But regardless of whether there are jointed bricks or seamless turning, it is best to leave joints, because everything has thermal expansion and cold contraction, and it is best to leave expansion joints.

Before the decoration, I heard others say that seamless tiling is good, seamless or fine seam paving effect is more beautiful, can make the wall and ground look smooth and tidy, think about it, leave the seams, the seams are easy to get dirty, yellow, mildew, ugly, and difficult to clean, so decisively chose seamless tiling, the guerrilla workers did not persuade me to paste, but I didn't expect that later the tiles were arched.

I don't know where it came from, but the concept of "seamless bricks" seems to be particularly popular recently? But my experience tells you that don't listen to rumors, don't choose seamless tiling, and it's too late to regret it;

However, do you know why there are seams when tiles are laid?

Ceramic tiles are not absolutely uniform specifications, there are errors, we all know that there are no two identical leaves in the world, any product can not be exactly the same size, weight, etc. in the production, this is the error, tiles are the same, even the same model of the product may have deviations.

There are also errors in construction, and there will be some errors when workers are constructing;

The tile itself will expand and shrink in heat, and the temperature change in the gap is too small to cause the tile to arch and crack in the later stage, so it is necessary to leave the seam to adjust the error and prevent thermal expansion and contraction.

So how much is the appropriate seam for commonly used tiles?

1.When seamless bricks and polished tiles are paved, the joints should generally be left and right, not less than 1mm, and the cross card given by the tile store can be used as a reference;

2.Generally, the water absorption rate of antique bricks is higher than that of vitrified bricks and full glaze, and the joints of antique bricks are still quite good-looking, leaving a 2mm 3mm and some of the quality is a little worse The water absorption rate is higher, and the gaps are more played.

3.The cultural bricks on the exterior wall of the balcony are generally seamed at about 5mm;