How to dismantle the glass door, how to disassemble the tempered glass door?

When it comes to double glazing, it is actually two pieces of glass separated from the ginger material through an effective seal, and a desiccant that absorbs water vapor is installed in the middle.

In order to ensure that the inside of our glass can be kept dry for a long time, this kind of double-layer glass is used very much in China's industry, and now it is also widely used in our construction industry, so for this double-layer glass, how should we disassemble it? If it is used in home renovation.

How to replace the glass with a new one!

How to remove double windows

First push the two windows together and overlap them, hold the window sash on the outside with both hands, lift it up forcefully, and then slightly outward, move the lower part of the window sash out of the window rail, then hold the window sash down forcefully, and the upper part of the window sash will come out of the window frame. The sash on the inside can also be removed in this way, because the sash on the outside has been removed, which is easier to remove. When disassembling the window sash, pay attention to safety, in order to prevent falling out of the hand, two people cooperate.

But sometimes the window sash may not be lifted, this is because the side of the plastic strip is restricted, you can carefully observe the side of the window sash up and down the groove, this plastic strip is also called the anti-theft plate, is stuck with a plastic clip, you can use a screwdriver along the gap to gently pry it down, the window sash can be removed. When you're done, put the security plate back on. If you come across a window lock, remove the lock.

In addition, there is a protruding object in the slot on the top of the window frame, which may also block the window sash and cannot be removed. The function of this object is a limit, which is fixed with screws and can also be removed. But it's mounted on the side and shouldn't be touchable.

How to change the glass for a double window.

Remove the broken glass first: use a greasy knife or a thin blade to remove the pressing strip of the glass first, remove the two long pressing strips, then disassemble the two short ones, and then remove the double glazing to clean up the debris. Be careful not to hurt the seal in the middle.

The contact surface is inserted flat with a greasy knife and cut on it.

Replace the new glass: wipe the new glass clean, and at the same time wipe the inside of the original layer of glass, otherwise it will not be wiped when it is installed. Clean the contact surface of the sealing strip, put the glass, confirm that there is no debris and dust inside, and use glass glue.

Seal. Replace the glass: After the glass glue is dry, put the double-layer glass back, contrary to the dismantling, first install a short strip, and then install a long strip. Then polish the glass and replace the plastic steel window glass and it is completed.

The above is one of the methods for disassembling and replacing our double glazing. Double glazing has excellent thermal and acoustic insulation properties, which can be very beneficial for preventing noise. Therefore, in recent years, it has been loved by everyone, especially some small high-level officials.

The glass door is generally used in the ground spring, the top screw is the top shaft adjustment screw, counterclockwise rotation to retract the top shaft, so that you can take the door down (individual need to rotate clockwise), if not, see if the adjusting screw has been dislocated.

Do you want to go fast or slow! The fast ones are smashed directly with a hammer, and the slow ones are smashed! You can look at that spring, which can generally be removed from **.

Generally, there will be a metal baffle near the seat of the hinge above the door, and the door can be removed by removing the screws of this baffle.

The steps to remove the glass door are as follows:

1. First of all, it is necessary to determine that the accessories above your ground tension spring door are equipped with a solid door frame (or aluminum frame) or with a glass clamp, and a solid door frame accessory: open the door to a 90-degree positioning viewpoint, use something to pad the lower corner of the door end of the handle, hold the door by yourself, and use a screwdriver to adjust the accessories on the top of the door.

2. Equipped with glass clamp: take away the stainless steel cover of the glass clamp and the lower clamp on the door, open the door to the 90-degree positioning viewpoint, use something to cushion the lower corner of the handle to open the door, one holds the door by himself, and the other uses a 6-corner key to unscrew the screws of the fixed shaft sleeve on the upper and lower door clamps of the door, and the shaft sleeve can be taken down. If you only take down the upper door clamp sleeve of the door, the door is skewed a little point of view, and the door can be lifted a little higher when the position is sufficient, so that you don't need to remove the lower door clamp sleeve of the door.

The mechanism for removing the glass door leaf is not in the ground spring, but in the upper transverse edge - there is a piece integrated with the door shaft, and a screw rod (there is a screwdriver suspension mouth on the surface) can be seen when looking in the same direction as the door leaf, and the screwdriver is rotated counterclockwise, and the upper door shaft will be adjusted to a higher (at this time, people must hold the door leaf and pay attention to safety), and when the door shaft is adjusted to a certain height, the door leaf will be removed.

The door opens a little and you can see the shaft above the door. There is a screw on the shaft, and the mouth is screwed with a word change cone downward, and two people are found to hold the door well. Take the cone to loosen the screws until the door is disengaged from the upper shaft, and then you can put the door back in place.

Then close the door, pull the top of the door slightly out of the frame, and pry something slightly hard from the top of the ground spring.

1. Replace the door glass

The door glass is actually very easy to replace, the main job is to disassemble the door trim panel, especially pay attention not to damage the door trim panel, the specific method is as follows:

First, find and remove the hidden bolts;

2.Take off the buckle and boldly disassemble the door trim panels;

3.Adjust the windows, remove the glass fixing bolts, and remove the glass.

2. Replace the sunroof glass.

When replacing the sunroof glass, remove it together with the sealing rubber ring when dismantling, and generally only the assembly can be purchased when purchasing glass, so you can install it according to the reverse steps of disassembly.

Some people think that the roof should be dismantled, and the motor should be dismantled, etc., which can not be destroyed without seepage, if the motor is really broken, then it is possible to quietly dismantle the roof and sunroof skeleton.

3. Replace the rearview mirror.

The rearview mirror replacement steps are also very simple, general accessories stores, not only sell lenses, only sell rearview mirror assembly. Open the door and remove the door trim panels, and some cars can replace the mirrors without dismantling them. When buying a rearview mirror assembly, pay attention to the fact that there are electric and manual, although the shape is the same, it is still necessary to choose carefully.

Fourth, replace the triangular glass.

Some triangular window panes are glued like a windshield.

Bonded, some are fixed by screws and screws, this type of model first has to find the position of the screws and screws, a cluster of transport can be seen under the sealing strip, bolts are installed under the interior panel.

The first step is to open the door trim, remove the fixing screws of the glass lift and the glass, and finally remove the glass.

Hello friends.

1.One. Replacing Door Glass: Door glass is actually very easy to replace, and the main job is to remove the door trim panel ,..

2.First, find and remove the hidden bolts;

3. Disconnect the buckle and boldly disassemble the door trim panel;

4. Adjust the windows, remove the glass fixing bolts, and take out the glass.

5.Two. Replace the sunroof glass When replacing the sunroof glass, remove it together with the sealing rubber ring when dismantling, and generally only the assembly can be purchased when buying glass, so you can install it according to the reverse steps of disassembly.

Dear, I'm glad to answer for you: balcony glass door dismantling method A: Good morning! <>

1. There is a screw on the top of the glass door, and use a screwdriver to unscrew the snail royal wire. 2. Remove the floor spring of the glass door. Then the glass door can be dropped, and then let a person hold the glass door to prevent the problem of falling, and use something to cushion the lower corner of the glass door.

3. Use a screwdriver to adjust the accessories on the upper part of the glass door to a certain height, and then unscrew the screws of the door fixing sleeve, and the whole glass door can be loosened. Thank you for your patience. The above is all my reply, if you are satisfied with my service, please give a thumbs up, and I wish you all the best!

Peace and joy to dismantle Naile!

Summary. Because the glass door is installed with a floor spring, the floor spring must be removed when disassembled, and in the process of disassembly, there is a screw at the top, and we need to use a screwdriver to unscrew the screw. 2. Next, you can disassemble the glass door, a person should hold the glass door to prevent the problem of falling, use something to pad the lower corner of the glass door, adjust the above accessories to a certain height with a screwdriver, and then unscrew the screw of the door fixing shaft sleeve, and finally the whole glass door can be loosened.

Hello, upon inquiry:

There is a screw on the top of the glass door, and you can unscrew it with a screwdriver. At the same time, someone needs to hold the glass door to prevent it from falling.

2. Remove the ground spring of the opening direction and angle of the door of the adjustment calendar that is carefully embedded in the ground, and the person who supports the door should hold it steady to prevent the door from falling off the door frame. The underside of the glass door should be padded with something soft, so that the glass can prevent it from bursting. 3. Finally, use a screwdriver to adjust the accessories on the top of the glass door, and use a screwdriver to unscrew the shaft sleeve of the fixed door, so that the glass door is removed.

This kind of door. Because the glass door is installed with a floor spring, the floor spring must be removed when disassembled, and in the process of disassembly, there is a screw at the top, and we need to use a screwdriver to unscrew the screw. 2. The glass door can be dismantled quietly by taking it down, a person should hold the glass door to prevent the problem of falling, use something to pad the lower corner of the glass door, adjust the accessories above with a screwdriver to a certain height, and then unscrew the screw of the door fixing shaft sleeve, and finally the whole glass door can be loosened and disturbed.

See. There are pressure strips on all sides.

Tap it with a wallpaper knife.

Knock on the beads around the perimeter and the glass can be removed.

The glass sliding door uses a frame made of magnesia steel or plastic steel, and the method of disassembly is the same as that of the wooden sliding door

1. Move the glass sliding door to the first position.

2. Use one hand to lift the glass sliding door upwards.

3. Use a screwdriver to unlock the door clip.

4. Lift the door with both hands up and come down.

5. The other door can be removed using the same method.

1. Find the sliding door on the bottom rail of the plug cover and cover the adjusting screws of the drum. Look at the cover on the door panel with the ends facing downwards.

2. Insert a small flathead screwdriver between the plug and the frame. Pry the plug and walk out the door.

3. Insert the screwdriver into each hole and lower the drum and rotate the adjustment screws counterclockwise.

4. Remove the head stop from the top of the inside of the frame on the track. The head station is a piece of metal, suitable for the track and door. Use a cordless screwdriver to remove the fixing bolt and stop the fixing head.

5. Open the sliding door and grab each side with the door panel. The door on the elevator, and the door at the bottom of the lower rail that pulls up, full marks. Lower the panel pull the door panel on the track. The door panel sets your way out.

6. Disconnect the sliding glass door that fixes the panel from the frame. Depending on your particular door, you may have set screws along the top, bottom and sides. Remove the set screws with a cordless screwdriver.

7. Lift the panel, pull out the bottom track of the bottom of the panel. Settings panel, your way out.

8. Remove the door frame frame that screws the latch and fix the door frame frame with a cordless screwdriver panel on the door frame.