How to open the sewage outlet of the water heater and how to clean it

1.Disconnect the power supply and unplug it first, and consume the hot water inside to prevent the hot water from being scalded during cleaning;

<>2.Turn off the inlet valve and outlet valve, unscrew the inlet and outlet nozzles, find a drainage pipe to connect to the water inlet and drain the water in the water tank slowly;

3.Use a fixed wrench to unscrew the sewage outlet (i.e. the fixing nut on which the magnesium rod is installed) and discharge the sewage from the sewage outlet, which is orange rust liquid;

4.Plug the sewage outlet with a small cloth, reconnect the water pipe, fill the water inlet into the water tank, stop after 10-20 seconds, and then pull out the small cloth blocking the sewage outlet to discharge the sewage inside. Repeat the above steps about 5 times The water tank is basically clean and free of impurities, if the discharged water is still a lot of impurities, then continue to operate as described above many times until the discharge is clean water;

5.Reinstall the magnesium rod at the sewage outlet and make sure it is tightened;

6.Reconnect the water inlet pipe and outlet pipe, first open the shower in the shower room, and then open the water inlet and outlet valve of the water heater, the purpose is to discharge the air in the water tank through the shower head through the water inlet pressure, and the shower can be turned off after the water is normally discharged, plugged in the power supply to heat, and resume normal use.

There is a screw cap at the bottom of the Midea electric water heater, find a suitable tool to unscrew it and take it off, be careful not to burn your hands. Then remove the plastic cover of the water heater and you can see the sewage outlet of the water heater, and then gently pry the sewage outlet open, then the sewage in the inner tank of the water heater will flow out with dirt, and it can be properly cleaned and assembled.

The method of opening the sewage outlet of Midea water heater is as follows:Tools: Midea water heater JSQ30-MK3, power switch, plum pliers.

1. Turn off the power switch to ensure that the water heater has no current, and close the water valve switch to ensure that there will be no water flow through the water heater.

2. Turn on the faucet at home, unscrew it to the maximum, and pay attention to rotate it to the hot water side.

3. Open the sewage outlet at the bottom of the water heater, and find a container to connect the water underneath after opening.

4. At this time, take a tool, plum blossom pliers are OK, gently open the sewage outlet valve of the water heater, and be careful when opening it to prevent the connected magnesium rod from breaking.

5. At this time, you will find that a lot of sewage and various impurities flow out of the sewage outlet, and after all the impurities are discharged, you can clean them.

1. Unplug the water heater and close the household water supply valve.

2. Use a screwdriver to open the drain pipe. After unscrewing the only screw, be careful not to pull the lid down too hard and push gently in the direction of the drain cap screw.

3. If you use the sleeve to remove the magnesium rod on the sewage outlet, the water will flow out, but the water flow is very small at this time.

4. Use a wrench to loosen the hot water pipe of the water heater, accelerate the water flow in the sewer, and drain the dirt until the water in the water heater is clean.

5. If the hot water ** pipe is blocked, please open the water supply valve, pour the water from the water heater into the water heater, and then drain it from the sewer, and the dirt will be discharged again.

6. Clean the water heater first and make sure the drain is clean.

7. Close the sluice, tighten the hot water inlet, clean the magnesium rod, put it back into the water heater, and tighten the screws. Close the drain cover.

8. Open the sluice, put the water into the water heater, then turn on the water heater, and check if the water heater is working properly and there is no leakage. If there is no marking, the cleaning is successful.

Next to the hot water inlet. Not every model has it, if there is one, it is right next to the hot water inlet, there is a plastic cover on the outside or a large screw can be seen directly. If not, you can only open the side cover and remove the heating tube to clean up.

Teach you how to open the washing machine drain.

Hello Answer! After the power is off, turn on the electric water heater according to the manual, remove the heating device, the precipitation inside will flow out, clean off the scale on the heater, and install it in the opposite step, pay attention to the correct connection of the circuit and the rubber ring seal at the connection between the heater and the box. 1. Turn off the tap water first;

2. Remove the inlet and outlet pipes, and then remove the safety valve on the inlet pipe to discharge the water;

3. After the water is drained, remove the right end cover of the water heater and carefully remove the electric heating pipe;

4. At this time, you can see the scale on the electric heating pipe, turn the screwdriver upside down and gently tap the electric heating pipe with the handle of the screwdriver, and shake the scale on the electric heating pipe.

5. Pull out the scale in the inner tank from the bile of the electric heating pipe by hand, because the scale falls off the electric heating pipe, there is no scale on the inner tank.

6. Clean 2 sides, wipe the gallbladder mouth dry, and install it in reverse order** It is easier to learn the operation.

Part of the water heater drain is on the left side of the hot water outlet, remove the decorative cover, use a wrench to remove it in the counterclockwise direction, and the other part of the model water heater can only open the water heater panel (below or right), remove the power cord, temperature sensing line, heating pipe, etc., and then clean it.

Operating tools: Haier water heater, turn off the main power supply of the electric water heater.

1. First find the magnesium rod mouth of the water heater pointed by the red arrow on the smith water heater, as shown in the figure below.

2. After that, use a wrench to remove the magnesium rod mouth of the Smith water heater, as shown in the figure below.

3. After that, take out the magnesium rod of the Smith water heater, as shown in the figure below.

4. After taking out the magnesium rod, the sewage outlet will be opened, and the sewage can be discharged normally, as shown in the figure below.

PrecautionsThe electric water heater will have a certain amount of water stuck at the bottom of the inner tank after each use, and it will be reheated repeatedly when it is used again. Due to water quality problems, the heated water will scale on the inner wall of the electric water heater and around the electric heating rod, so that the microorganisms and impurities in the water have a place to multiply, and the water quality in the machine will be re-polluted.

People use such water to bathe, there are indeed health risks, especially children, the elderly, or people with relatively weak resistance, or people who have ** diseases, will obviously have ** itching, red spots and other phenomena. Some people also use water from the water heater to brush their teeth and rinse their mouths, which is even more harmful.

There is a screw cap at the bottom of the electric water heater in Midea, find a suitable tool to unscrew it and take it off, be careful not to burn your hands. Then remove the plastic cover of the water heater and you can see the sewage outlet of the water heater, and then gently pry the sewage outlet open, then the sewage in the inner tank of the water heater will flow and shout out with dirt, properly clean up and assemble it.

1. How to open and clean the sewage outlet of the water heater: unplug the power supply of the water heater and turn off the household water inlet valve. Use a screwdriver to open the drain.

After unscrewing the only screw, be careful not to pull the lid off with brute force, just push it gently in the direction of the screw on the drain cover. The magnesium rod is removed with a sleeve in the sewage outlet, and the water flows out, but the water flow is smaller. Use a wrench to unscrew the hot water outlet pipe of the water heater, the water flow from the sewage outlet accelerates, and the dirt is also discharged until the water inside the water heater is drained clean.

Block the hot water outlet pipe, open the water valve, and let the water from the water pipe enter the water heater and then discharge from the sewage outlet, and the dirt is also discharged again. See that there is no more dirt discharged from the sewage outlet, and the water heater has been preliminarily cleaned.

2. Precautions for using water heaters: When using water heaters, it is necessary to operate in strict accordance with the instruction manual, check whether the water heater is operating normally, and then turn on the water first.

3. When using the water heater, the window or exhaust should be opened, otherwise it may lead to hypoxia or carbon monoxide poisoning, so try not to use the water heater for a long time.

4. Be sure to check the water heater regularly, check the nozzle and ignition needle and induction needle of the water heater. If the water heater is used for a long time, the nozzle and the ignition needle are more likely to accumulate carbon, which will affect the normal use, so clean the nozzle and the induction needle and the ignition needle in time after long-term use.