If the door can t be closed, how to get it, and what to do if the sliding door can t be closed tight

First of all, see if your refrigerator is a refrigerator or a freezer that won't close the door; The refrigerator room should look at whether the door shaft and door seal are deformed, and if they are deformed, they should be repaired directly by after-sales or maintenance personnel; The freezer room should see if the drawer is pushed to the bottom, and whether there are too many things to put on the bottom and get stuck; The drawer can't be pushed to the end, and the door is not closed tightly; Secondly, see if there is ice at the bottom of each drawer, and if the ice is thick, it can withstand the drawer and the door is not tightly closed;

Specific issues and specific amendments. The door won't close, probably because the door frame has been deformed, causing it to sag. In this case, the door frame can be removed first, and the sunken part can be broken with the planer used in the carpentry, and then the door frame can be reinstalled.

If the door does not close because the screws are loose, find the loose screws and retighten the screws. If there is a problem with the hinge and hinge, replace the hardware accessories with new ones, and then drip lubricating oil, and the switch will be free. Regarding the problem of door sinking, you can also use a wooden wedge, choose a small molded wooden block, and stuff it directly into the gap under the door, which can prevent the door leaf from continuing to sink.

In addition, adjust the hinge again, which can solve the problem of not being able to close the door.

If it is caused by sagging, you can first remove the door frame, use a wound to create the part that has sunken, and select a molded wooden block to plug it into the gap under the door. If the door cannot be closed due to loose screws, find the loose screws first, and then retighten the screws. If there is a problem with the hinge and hinge, replace the hardware accessories with new ones and then drip lubricating oil.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose.

Villa Master.

(1) The installation of doors and windows should conform to the installation process, and the installation quality of each process should be checked and adjusted at any time.

2) The window frame and the window hole should be drawn out of the center line, the window frame should be aligned with the center line when the hole is loaded, the corner of the frame should be temporarily fixed, and the verticality, horizontality and straight angle of the window frame should be carefully adjusted, and the error should be within the allowable deviation range.

3) Before the door and window sash is put into the frame, the diagonal and flatness deviation should be checked, and the lap width and surrounding gap of the frame should be checked with a steel plate ruler and feeler gauge until it meets the requirements.

4) Install the hardware parts correctly, and replace them in time if they are damaged.

5) Do a good job in the protection of finished products and the usual use and maintenance to prevent external impact, and do not hang heavy objects, resulting in deformation of doors and windows. When in use, it should be opened and closed gently to prolong its service life.

If there is a blockage phenomenon when opening and closing doors and windows, the switch requires a lot of force, the lap width of the frame fan is small, and the surrounding gap is uneven, it is generally caused by the following factors:

1) The door and window frame or sash is deformed, and the sealing strip is loose and falls off.

2) Hardware accessories are damaged.

3) The installation quality is poor, and there are many deviations beyond the allowable deviation, and it is not adjusted in time.

When installing, pay attention to the following points to ensure the sealing of the hinge:

1) Before installation, check whether the hinge matches the door and window frame and sash.

2) Check whether the hinge groove matches the height, width and thickness of the hinge.

3) Check whether the hinge and the screws and fasteners connected to it are matched.

4) The connection of the hinge should match the material of the frame and the sash, such as the hinge used in the steel frame wooden door, the side connected with the steel frame is welded, and the side connected with the wooden door leaf is fixed with wood screws.

5) In the case of asymmetry of the two pages of the hinge, it should be distinguished which page should be connected with the sash, which page should be connected with the door and window frame, one side connected with the three sections of the shaft should be fixed with the frame, and one side connected with the two sections of the shaft should be fixed with the door and window.

Doors and windows leaking and not closing tightly are things that every family will encounter, carefully observe these points to create a warm space.

There are two kinds of problems: 1. The sliding door track Rose is loose, and then reinforced. 2. It may be that the main reason is that the base layer under the track of your sliding door has not been done well and has fallen.

The base layer of the sliding door track embedded in the wall should be welded with an iron square pipe, and a layer of wood should be pasted on the square pipe, and the extended rose can be directly connected to the square pipe when installing the sliding door track.

Note: You check your base.

An uneven foundation can cause this;

To solve the problem quickly at a low cost, it is to install a strong magnetic suction and install it directly with a blind rivet.

The main purpose of sliding the door is to pay attention to the lubrication of the slide rail, otherwise there will be abnormal noise, poor movement or misalignment.

Our sliding door factory adopts professional sliding door wheel rail grease, which is colorless and transparent, with good adhesion and good durability. Tiger head hotolube or Kruber can be used, with food-grade safety certification, suitable for household use. There are 130 grams of tubes in the sleeve.

When using, apply directly to the slide rails and pulleys, and open and close the sliding door a few times.

Do not use lubricating oil and regular butter on the slide rails and slides of the sliding doors, as the lubricating oil will be lost quickly. Regular butter will have a harmful smell that is not good for the human body.

I want to ask the master at that time when he installed it for you, did the quantity level? It may be the cause of uneven ground, if the ground is uneven, then it is okay to level the ground. Try it, I hope it helps.

Summary. Dear, glad to answer for you! The solution to the door closer being too tight:

There is a small opening on the right side of the door closer, and there are screws in it, which are tightened. There are two valves next to the door closer, which can adjust the speed, but not the weight. The chosen door closer was too heavy.

If you change the model to a smaller one, you should choose the door closer according to the width and weight of the door. There is also a lot of difference between the strength of domestic and imported ones, and if you can't adjust it smoothly when you close the door, it is a very poor door closer. A good door closer is one that closes the door very gently.

Dear, glad to answer for you! The solution to the socks if the door closer is too tight: there is a small opening on the right side of the door closer, and there are screws inside, which are tight.

There are two valves next to the door closer, which can adjust the speed, but not the weight. The chosen door closer was too heavy. If you change the model to a smaller one, you should choose the door closer according to the width and weight of the door.

There is also a lot of difference between the strength of domestic and imported, if you close the door, how to shoot and search unstable is a very poor door closer. A good door closer is a cave calendar that closes the door very softly.

Installation method of door closer: 1. First of all, the door closer and the hinge side should be installed together, and it needs to be installed in the direction of the door opening, otherwise forced opening may cause damage to the door leaf and door frame on the door closer. 2. Then fix the door leaf with screws and the body, then put one side of the rod on the gear, and fix the cap with a screwdriver on the other side.

3. Next, use screws to fix the door frame and the rod together, and then adjust the length of the rod according to the actual situation. 4. Put the washer on it after zui, and then fix the screws and tighten the trapped chain.

1. If the deadbolt is short, replace the tongue lock, reinstall the door lock and other components, remove the old one, and then install the new one in the original position.

2. If the door leaf is sinking, the hinge on the door leaf is deformed or loose, which will cause the door to be closed loosely, and the hinge only needs to be tightened to solve the problem of the door not being tightly closed.

3. If the door leaf or door sleeve is deformed, you can use tape or cloth to stick it in the gap, although it will affect the appearance, but it can effectively close the door.

4. If the lock of the door cannot be closed normally, you can also install a latch on the door frame, which can use the latch to close the door, and you can also stuff a wedge-shaped wooden block in the gap of the door, which can effectively deal with the problem of not closing tightly caused by sagging.

It may be that the hinges of the door are not good, or the problem of the door lock, it is recommended to find someone to check it, if the hinges of the door are not good, it may be because the installation is not adjusted well, or the hinges of the door themselves are not of good quality, this hinge is generally used on the wooden door. If it is a problem with the lock, it is recommended to change the lock to try, if it still doesn't work, then you can only change the door. If it is a problem with the wooden door, then you need to find the manufacturer of the wooden door to repair it, because this is the quality problem of the wooden door, so you need to find the manufacturer of the wooden door to solve the problem.

1. Make sure that the lock cylinder is not damaged, you can repair it yourself, check whether the deadbolt and the door frame are loosened due to the displacement of gravity impact, whether the gap between the deadbolt is too large after popping up, and the door can generally be intuitively judged after closing the door, and if necessary, replace or repair the lock head and adjust the door frame lock cylinder groove fixing parts to solve the problem.

2. If the door is deformed or the hinge is faulty, you should find the manufacturer to check. The key is not easy to pull, so you can solve it by dipping a little oil on the key and putting it in the keyhole to move back and forth. The anti-theft door with a lock is loud when the door is closed, and it is difficult to close the door when the lock is closed, mainly because of the problem of touching the deadbolt, you can grind some lead or soap on the inclined surface of the deadbolt to play a role in lubrication, and the door will naturally be much easier.