How to remove the sliding door How to remove the sliding door

Generally, the sliding door of the two doors is moved on the ground by rollers at the bottom, and the top is lifted by the keel of Guizhou Jiagui. In the track above, the two screws are fixed in the notch between the track and the door and window, first remove the two screws, and then the busy track is temporarily connected as a whole, and then the two doors are in the middle position, and then the bottom is moved along to one side The top will be separated from the notch of the cute frame, and then the sliding door will be removed directly.

1. One person lifts a door so that it is not affected by the top pulley.

2. A person uses a slender stick such as a screwdriver to gently move the top pulley of the lifted door outward and detach it from the position of the door.

3. The door can be lowered when the pulley is detached from the sliding door (this requires a lot of effort).

4. The door without pulleys cannot slide freely, lift the door again and drag the lower part outward.

5. After the door is removed, it needs to be installed back, the steps are the opposite of the steps removed, it should be noted that when the pulley is dialed back to the iron groove at the top of the door, you need to be patient, not too hard, otherwise it will be counterproductive.

Introduction]: Sliding door is a commonly used door in the family, which refers to the door that can be pushed and pulled. With the development of technology and the diversification of decoration methods, the function and scope of use of sliding doors are constantly expanding from the traditional plate surface to glass, fabric, rattan weaving, aluminum alloy profiles, from sliding doors, folding doors to partition doors.

1. Find the sliding door on the bottom rail of the plug cover and cover the adjusting screws of the drum. Look at the cover on the door panel with the ends facing downwards.

2. Insert a small flathead screwdriver between the plug and the frame. Pry the plug and walk out the door.

3. Insert the screwdriver into each hole and lower the drum and rotate the adjustment screws counterclockwise.

4. Remove the head stop from the top of the frame on the inside of the track on the top. The head station is a piece of metal, suitable for the track and door. Use a cordless screwdriver to remove the fixing bolt and stop the fixing head.

5. Lift the panel, pull out the bottom track at the bottom of the Foshan sliding door panel. Settings panel, your way out.

6. Remove the door frame frame that is screwed to fix the latch and the door frame frame that is fixed in the door frame with a cordless screwdriver panel. The latching side sliding door handle on the latching frame closes the latch. Fixed door frame on one side is the fixed panel is located.

Set the screws to the center of the frame of the entire door frame. Insert a small flat door frame between the crowbar and the house frame door frame after prying and remove the screws.

7. Pull the openings of the two tracks on the upper and lower tracks where the screws are removed.

First of all, it is necessary to determine the sliding doors of different periods and materials, which generally have different structures, but the general disassembly method is the same.

At present, there is a pulley at the top of the general wooden door and aluminum alloy door, and the pulley is connected with the sliding door by bolt.

Lift the sliding door up slightly and flick it sideways with a screwdriver.

Remove the pulley on the other side in the same way, and then lift the sliding door upwards so that the lower end of the door leaves the alignment pin, so that the lower end of the door is removed outward first.

How to remove the sliding door:

1. Lift the sliding door first, and then take the screwdriver.

Move the pulley outwards and let it move away from the sliding door.

2. Then put down the sliding door, the sliding door will not move after losing the pulley, and then lift the sliding door and drag the pulley below.

3. After the pulley is taken out, the sliding door can be disassembled.

What are the common sliding door materials?

1. The wooden structure sliding door, its material is taken from nature, the appearance of the texture is clear, the touch is strong, so that people have a warm feeling, but also can improve the home decoration, but it is widely welcomed by people, but this material can not be used in the humid environment, otherwise there will be the problem of mold, so the corresponding moisture-proof measures must be done.

2. Plastic steel. Sliding doors are widely used in the north to withstand strong winds due to their excellent sealing effect and the fact that the outer layer does not deteriorate and deform easily, and can be equipped with insulating glass if there is a lot of noise around them.

In this way, good sealing and sound insulation can be guaranteed.

3. Aluminum alloy sliding door, its high strength, light weight, will not be easy to age, and can be used for a long time, and the doors and windows of this material are economical, widely used, green and environmentally friendly, so it is widely loved by people and can be used in humid environments such as bathrooms and kitchens.

1. One person lifts a door so that it is not affected by the top pulley, and one person uses a slender stick such as a screwdriver to gently move the top pulley of the lifted door outward and get out of the position of the door.

2. The door can be lowered when the pulley is separated from the sliding door, and the door without the pulley cannot slide freely.

3. Lift the door again and drag the lower part of it outward, the door needs to be installed back after being removed, and the steps are the opposite of the steps removed.

4. Pay attention to one point, don't push the pulley back to the iron groove at the top of the door, and you're done.

The side of the sliding door fell down, how to fasten it.

In addition, the plastic strips on the side and the screws in the slot need to be fixed on the side, and the limit buckle must be dealt with in advance. In the second step, we need to clean the grooves around the door, and finally just reinstall the sliding door and reset the limit buckle to press the sliding window back again.

Hello, I have seen your question and am sorting out the answer, please wait a while

Use a screwdriver to gently move the top pulley of the lifted door outward and remove it from the position of the door. zhi

When disassembling the sliding door, first check the installation method and safe use of the sliding door, determine whether the sliding door can be disassembled, while dismantling, pay attention to the control of noise, so as not to disturb other people around, when disassembling the hanging rail door, you need to pay attention to ensure that the width of the two doors must be consistent, and you need to choose a better quality door before dismantling, so that the use time can be extended for a long time.

Generally, the sliding door of the two doors is moved on the ground by rollers at the bottom, and the top is lifted by the Guizhou Jiagui dragon bone. In the track of the upper subordinate party, the two screws are fixed in the notch between the track and the door and window, first remove the two screws, and then the busy track is temporarily connected as a whole, and then the two doors are in the middle position, and then the bottom is moved along to one side The top will be separated from the notch of the Meng frame, and then the sliding door will be removed directly.

One person lifts a door again so that it does not slip from the top.

the role of the wheel; A person uses a slender stick such as a screwdriver to gently move the top pulley of the door that is lifted outward and out of the position of the door;

The door can be lowered when the pulley is detached from the sliding door (which requires a lot of effort);

The door without pulleys cannot slide freely, lift the door again and drag the lower part outward;

After the door is removed, it needs to be installed back, the steps are opposite to the steps removed, pay attention to one point: turn the pulley back to the door; When using the iron groove at the top, you need to be patient and don't push too hard, otherwise it will backfire if it is too much. That's it.

The bottom edge of the two doors is moved on the ground by rolling the wheel, and the top is fixed by the slide rail du and pulley. The mystery is in the track above, the two screws are fixed in the notch of the door frame, remove the two screws, and the track of the door is temporarily connected as a whole. Place the two doors in the middle position and move the bottom edge to one side so that the upper part will break away from the notch in the door frame and be removed.

Then, detach the door from the track.

1: The sliding door can be directly pushed down, 2: The glass is directly adsorbed with a suction cup-like tool, and it can be directly lifted and disassembled.

3: I really don't understand the doors and windows in my Shangyue, their company specializes in sliding doors.

It's not easy to dismantle yourself, you need to hold it up, detach the track pulley, and it will fall off, it is more dangerous to operate alone, find a worker to help! Safety first!!!

Put the screws on the slide rail down, a person carefully protect the point, or can be removed, carefully remove the door when the door is reversed.

It is a hanging type, depending on the location, first remove the screws with a special unit, and then disassemble it. Not a big problem.

How to unload the sliding door that opens outward: The disassembly method of the sliding door is relatively simple, first you need to grasp the bottom of the sliding door with your hands, and then lift it up forcefully, so that you can let its bottom out of the lower track, and then you can take out the sliding door. Friends who don't know how to operate can find a professional to come to help, when disassembling the sliding door, you must be careful, you must not break it, otherwise there is no way to continue to use.