What should I do if the little solar heater of Midea is broken?

The small solar heater is broken, in fact, the fault is very simple, and it can be repaired in a few minutes by following the steps.

Here's how to repair a broken small solar heater:

1. The fundamental reason for the heat fluctuation is that there is poor contact in the circuit, including loose sockets and switches, loose heating wire lead joints, and fuse points of the heating wire itself.

For the newly used electric heater, if the heat is high and low, in most cases, it is because a certain fastening screw is not tightened during production and installation.

2. It is also a common fault that the small solar heater suddenly does not heat, and it is found that the household electric heater does not heat up and the indicator light does not light up, first of all, it is necessary to confirm whether the power socket has a normal power supply, carefully check whether the plug is loose, whether the power cord is damaged and leaking, and also check the electric heater switch position, temperature control switch, etc.

It is also necessary to check whether the heating wire of the heating element is broken, that is, whether the heater is disconnected, and see if the wiring of the heating pipe is loose or in poor contact.

3. If the power supply is not connected to the circuit, disassemble the face cover of the electric heater, turn on the power supply, if the power cord is faulty, open the rubber cover of the power cord socket to see if it is the power cord, which is caused by the user often pulling the power cord and pulling out the socket. Reconnect the L lead, and the fault will be eliminated. If the cord is not broken at the socket or plug, the power cord needs to be replaced.

Maintenance of small solar heaters:

The small solar heater should also be maintained during use, so as to extend the service life of the product.

In daily use, we should keep the internal heating vertical surface of the small solar heater and the guard clean to prevent excessive dust from causing circuit failure, and we should have a good habit in use, when not in use, we should cut off the power supply in time, so as to prevent the loss of electrical components.

If the small solar heater needs to be disassembled, it must be disassembled by a professional maintenance personnel. The heater should not be disassembled without authorization to avoid the safety accident of electricity in the future use of the heater.

Do not place the heater in a damp place to avoid the metal being corroded and the service life will be shortened. When using the heater, do not place the socket directly above the heater, as once the heater is turned on, the heater will have heat coming out, and the heat may burn the socket when it rises.

Electric heaters must use a three-prong outlet. The heater is of high power, and a qualified three-pin socket with a ground wire must be used, otherwise there will be a risk of leakage. It should not be used at the same time with high-power electrical appliances, as well as electric welding machines, percussion drills, etc., otherwise it is easy to damage the electric heater.

The socket should not be located directly above the heater to prevent the heat from rising and scalding the power supply.

The little sun shook his head and could be repaired without heating.

The small sun shaking head electric heater does not heat up, and it should not be very difficult to repair, and there is no great technical content. Disassemble the small solar heater, measure it with the resistance level of the multimeter at 100 ohms, measure whether the switch is normal, and then measure whether the timer is accessible.

If the measurement pointer is deflected to the zero position in the open position, the switch and timer are fine. If the pointer is motionless during the measurement, it means that the switch or timer has been broken, and then measure whether the plug to the switch has access to the continent.

If it is normal, then measure whether the heating element is accessible, and the pointer reaches zero, which means that it is normal. If the pointer does not move, it means that the heating tube is broken, and you can buy a new one and replace it with a part of the same model.

Heater features:

Heating wire heating source far infrared, reflective, convection heater is a very common type of heater. A concave mirror-reflective heater is commonly known as a small sun.

Regardless of the desktop type, the Lishou imitation base type can shake the head like an electric fan, and some have far-infrared function and no noise. The heating speed is faster. The disadvantage is that the heating wire is fragile, and large vibrations in the open state may cause damage to the heating wire.

Heat conduction oil heating source electric heating oil tint electric heating oil tint uses heat conduction oil as the heating source, the temperature can be set at will according to the need, no noise, no peculiar smell, long service life, no brightness, no oxygen consumption, and the air is not as dry as the reflective type when used.

The maintenance method of the small solar heater is not hot is as follows

Disassemble the small solar heater, measure it with the 100 ohm level of the multimeter resistance file, measure whether the switch is normal, and then measure whether the timer is accessible, if the measurement pointer is deflected to the zero position in the open position, it means that the switch and timer are fine.

If the pointer does not move while measuring, the switch or timer is broken. Then measure whether the plug to the switch is connected, if it is normal, then measure whether the heating element is accessible, the pointer reaches zero, which means that the heating element is broken.

For switches, timers or heating tubes, as long as one of the nuclear attack is broken, the electric heater will not heat, buy a part of the same model to replace it, if necessary, soldering it with a soldering iron.

The resistance wire in the small solar heater is broken. In this case, the resistance wire can be replaced, but the cost is relatively high, and it can also be replaced with a new one. There is a possibility that the power cord and socket may be in poor contact. Go to a professional maintenance personnel to bring professional equipment to deal with and remove obstacles.

The internal parts of the small Taiyuan Yang heater are damaged and cannot be used. Go back to the factory to rebuild or buy a new little sun in Shan's line. From the power supply, to the power cord plug, to the switch, to the timer, to the heating unit, the inspection is carried out.