What are the correct steps to paint cement floors? What do I need to pay attention to when painting?

The first point should be brushed with a very beautiful layer of cement, so as to achieve a good effect, the second step of brushing, the face should be cleaned very clean, the third point should be careful not to get wet, so that you can, the 4th point should pay attention to this procedure, should be from left to right.

First of all, the ground is cleaned, and then the cooked tung oil and rosin perfume are mixed in proportion, the putty is mixed, mixed with a certain amount of cooked tung oil, stirred evenly, scraped to the ground where the paint is painted, and after drying, brush the floor paint. When painting, be sure to scrape the base putty flat, be sure to sandpaper for sanding, do not reduce the number of brushes.

The steps are to first stir the paint evenly until there are no particles, then fully soak the paint with a tool, then brush on the wall, first fix the point and then pull the line, and finally form the surface. Pay attention to the uniform brushing, otherwise the color will not look good.

The first step is to level the ground, the second step is to brush the primer, and the third step is to paint, the key is to pay attention to the flatness of the ground.

The cement floor in the home is generally paved with tiles or wooden floors as the mainstream decoration method. However, it is said that the austere way of decoration may only be the practice of varnish. But is it okay to paint a concrete floor directly?

This article intends to use this as a topic to introduce the steps of cement floor painting.

Concrete floors can be varnished. However, the bond between cement and paint is relatively poor. If you want to have a better effect, you need to have an intermediate medium to improve the adhesion of cement and paint, and this intermediate medium is iron putty.

Namely: cement - iron putty - paint.

No matter which brand of paint is used, a layer of iron putty must be scraped on a clean cement floor in advance, which has a good grip effect and a good combination with the ground.

1. First of all, the ground ready to be painted with cement floor paint is cleaned, (no river sand and no dust) The most thorough way is to sweep the dust with a broom first, and then mop it again.

2. Use cooked tung oil and rosin perfume in accordance with the ratio to mix, stir evenly and then paint on the ground of the penitential shirt. This can effectively enhance the adhesion between the cement floor and the putty.

3. Next, enter the deployment link of introducing putty. At present, the putty used in decoration is divided into two types: gypsum putty and blood putty

The preparation method of gypsum putty is: gypsum powder, cooked tung oil, pine perfume, tap water, according to the ratio of 16:5:1:6, stir evenly and use.

The preparation method of blood putty is: pig blood and large white powder, according to the ratio of 16::56, of course, in order to enhance the waterproof and wear-resistant performance of putty, it is also necessary to mix a certain amount of cooked tung oil.

4. After the putty is evenly mixed, we should enter the next environment, scrape the putty to the ground with a shovel to brush the paint in advance, generally scrape two to three articles is more appropriate, in short, the ground can be scraped flat, and then after the putty is dry, use 80 mesh sandpaper for polishing treatment, you can brush the floor paint.

5. In the process of painting the floor paint, it is necessary to pay attention not to be greedy, and the floor paint should not be applied too thick to avoid wrinkles. Floor paint is not a can be brushed, generally need about two times, in the second time to brush the green cavity must ensure that the first paint is all dry, and finally use floor wax to finish, so that it is done. The combination of cement floor and paint is poor, therefore, directly to the cement floor varnish, its effect is unsatisfactory, must go through a series of steps, in order to ensure the quality of cement floor paint.

Concrete floors cannot be painted directly. Due to the excessive concentration of floor paint, the viscosity is very high, so it cannot be brushed directly. Before construction, the paint and curing agent are fully stirred in proportion before construction, and an appropriate amount of epoxy diluent can be added to adjust the viscosity during construction.

If it is a large area, it should be polished, and it can be ground off with a water mill with a gold head, if it is a small area, it can be ground off with an angle grinder with a cement grinding disc, or it can be soaked in paint remover and shoveled off and then rinsed with water.