The tiles at home are still dirty after many cleanings, what should I do? Do I need to replace it?

Generally, you choose to use a special dish soap to clean, then wipe it with a wet towel first, and finally take it off with a rag, which does not need to be replaced.

You can directly choose to replace the tiles, and you need to choose the tiles to replace the tiles, and then let the master lay a little cement underneath.

Stubborn stains can be treated with special cleaning agents, such as the tiles behind the water pipe that are easy to rust can use rust inhibitors, you can also consider using the professional rust remover or part of the polishing, laminating, grease, anti-rust oil and other methods to prevent rust, if you really can't clean up you can consider replacing it with a new one.

1. Buy oxalic acid and prepare towels, gloves and masks.

2. Clean and wipe.

3. Cleaning the tail sweep is completed.

Chengdu Moyin Mountain decoration.

When cleaning the newly renovated floor tiles, the first step must be to use a broom to clean up the dust, and then splash water to wash, if it is a wooden floor, use a wet rag to wipe the dust.

The second step is to sprinkle laundry detergent or dish soap in batches, slightly moisten the water with a rag next to each other, and wipe it carefully and carefully, not letting go of the corners.

The third step is to use soap and a little ammonia and turpentine to clean the tiles to make the tiles more shiny. If there are marks such as cement, they can be erased by gently rubbing them with hydrochloric acid.

When cleaning the newly renovated floor tiles, the first step must be to use a broom to clean up the dust, and then splash water to wash, if it is a wooden floor, use a wet rag to wipe the dust.

The second step is to sprinkle laundry detergent or dish soap in batches, slightly moisten the water with a rag next to each other, and wipe it carefully and carefully, not letting go of the corners.

The third step is to use soap and a little ammonia and turpentine to clean the tiles to make the tiles more shiny. If there are marks such as cement, they can be erased by gently rubbing them with hydrochloric acid.

It is best to find the merchant again after cleaning, and re-wax the wooden floor to prolong its service life. Pay attention to moisture-proof in the gaps of floor tiles, and it is best to do a little waterproofing, otherwise it will lead to mold, etc.

What to do if the floor tiles after decoration are dirty, what to do if the floor tiles after decoration are dirty in three simple steps, what to do if the floor tiles are dirty after decoration in three simple steps, what to do if the floor tiles are dirty after decoration in three simple steps, what to do if the floor tiles are dirty after decoration in three simple steps, what to do if the floor tiles after decoration are dirty in three simple steps, what to do if the floor tiles are dirty after decoration in three simple steps, what to do if the floor tiles are dirty after decoration in three simple steps, What to do if the floor tiles after decoration are dirty, what to do if the floor tiles after decoration are dirty in simple three steps, what to do if the floor tiles after decoration are dirty, and clean them in three simple steps.

Because the bathroom generally uses glazed tiles, you can try toilet cleaner or hydrochloric acid thinner to clean the tiles to remove stubborn stains on the surface, and it is recommended that you do beautiful seam treatment for the gaps of the tiles, which is not only beautiful, but also prevents bacterial breeding.

I don't know what to stain, and generally difficult to wash stains have the following centralized treatment methods:

1.When buying tiles or selling tiles in the place there should be decontamination powder, wipe.

2.Diluted hydrochloric acid, wipe.

3.Wipe with low concentration of hydrogen peroxide.

Add some detergent and wipe it clean, and stubborn stains will be washed off with a little oxalic acid or Vermeer.

Use bus sanitizer or a powerful cleaning solution that resembles a grenade.

Wash with detergent or vinegar.

1. In the gaps of the tiles, you should first use a toothbrush dipped in a little detergent to remove the dirt, and then brush a waterproof agent with a brush in the gaps, which can not only prevent water seepage but also prevent mold growth.

2. When cleaning and maintaining vitrified tiles daily, all stains on the floor tiles should be thoroughly cleaned first, and if there is glue or sticky stains, they can be wiped off with neutral detergents and scouring pads. Sprinkle the floor cleaner on the floor tiles and rub the stains off the tiles with a waxing machine. Then pour the water-based wax onto a clean dry mop and spread the wax evenly on the floor tiles.

After waxing, let the surface of the floor tiles dry by itself, and then you can step on it after drying, or you can use an electric fan to assist in drying, generally 8 hours after waxing will be completely dry, if there is a heavy object to move, you must wait for the wax to be completely dry before moving, so that you can keep the light of the floor tiles.

3. If the tile is too dirty, you can use water, detergent or soap when cleaning; When cleaning with soap, add a little ammonia and turpentine mixture, which can make the tile smoother. If there is tea or other daily necessities attached to the tile, it should be scrubbed in time, and the corresponding cleaning products should be used to clean it if necessary. If there are scratches on the brick surface, you can apply toothpaste to the scratches, and wipe them with a dry cloth to repair them.