What should I do if the truck is not in good gear 2 gear? What is the reason why the truck stall is

The main reasons for the car's bad gear are the following three aspects:

1.Operational factors.

Incorrect operation of the driver, speed and gear.

mismatch, resulting in the occurrence of bad gearing, which requires the driver to explore experience, and the problem will be solved naturally after the operation is proficient.

2.Clutch factor.

There are four main problems in the clutch that will cause the car to be in bad gear:

1) Gearbox.

The first shaft is rusty, the clutch disc can not move normally, and the return is poor, so that the gear can not enter the gear according to the normal trajectory, resulting in the car is not good to hang the gear.

2) Clutch failure, so that the clutch separation stroke is not enough, and then cause the clutch separation is not complete and can not enter the gear, in such a situation, you need to go to the repair shop to adjust the separation stroke.

3) The clutch gear self-locking force is too large, which makes it difficult to enter and exit the gear, in this case, you need to go to the repair shop to adjust the clutch cable and gear lock.

4) The transmission plate of the clutch pressure plate assembly is deformed for some reasons, resulting in poor separation, resulting in poor gear of the car, and in this case, the pressure plate that matches the original car needs to be replaced.

Hello According to your description, the main reasons for the difficulty of gearing are: 1. The temperature of the car is low and the transmission oil is not fully lubricated. 2. If you don't ignite, try a gear to hang it well, and it's okay to hang it well.

3. It is not easy to hang up when changing a gear while moving, and the speed and gear do not match. 4. There is no synchronizer in the first gear and reverse gear. Workaround:

1.It is recommended to try to hang the reverse gear in the stationary state of the speed vehicle, if the gearbox is engaged in the reverse gear process, the gearbox makes a "click" gear impact sound, indicating that the clutch of the vehicle is not completely separated, and the fault can be eliminated after the clutch is repaired. 2.

If the reverse gear is smooth, only one gear is not good to hang, it is recommended that you go to the repair shop to adjust the gear position, change the transmission oil, and the fault can also be eliminated. The manual transmission shifts gears at low speeds, requiring the clutch to be able to disengage thoroughly in order to be able to engage the corresponding gear.

Summary. Hello, dear. The bad hanging of the truck gear is generally caused by the following conditions for your reference:

1. The vehicle can not be put into gear, and the possibility of problems with the synchronizer is relatively large, because the gearbox needs the cooperation of the synchronizer when changing gears, and if the synchronizer is seriously worn, the synchronization ability will be affected, and when the vehicle is in gear, there will be a situation where it is difficult to play teeth or hang the gear. 2. It may also be that when the transmission oil reaches the end of its service life, the effect of lubrication will be reduced, and it will be difficult for the vehicle to be in gear, and the owner needs to replace the new transmission oil. 3. If it is a new car, the gearbox is not fully run-in, there will be difficulties in gearing, and the owner needs a period of running-in.

4. It may be that the current temperature is relatively low, and the gearbox oil has not yet reached a good working condition after the vehicle has just started, and the vehicle will have difficulty in gearing, so it is good to wait for the temperature to come up.

Hello, dear. The truck gear is generally not good to hang is caused by the following situations, for your reference: 1. The vehicle cannot be hung up, and the possibility of problems with the synchronizer is relatively large, because the gearbox needs the cooperation of the synchronizer when changing gears, if the synchronizer is seriously worn, the synchronization ability will be affected, and when the vehicle is in gear, there will be a difficult situation of playing teeth or gearing.

2. It may also be that when the transmission oil reaches the end of its service life, the effect of lubrication will be reduced, and it will be difficult for the vehicle to be in gear, and the owner needs to replace the new transmission oil. 3. If it is a new car, the gearbox is not fully run-in, there will be difficulties in gearing, and the owner laughs at the grinding beam and needs to touch the grinding for a period of time. 4. It may be that the current temperature is relatively low, and the gearbox oil has not yet reached a good working condition after the vehicle has just started, and the vehicle will have difficulty in gearing, so it is good to wait for the temperature to come up.

The root cause of the gearbox failure is high temperature, and the reasons for the poor hanging are as follows: 1. The high temperature in the gearbox will destroy the quality of the gearbox oil and aggravate the friction; 2. At the same time, sludge will be generated in the gearbox; 3. The oil sludge will provoke Sun Que to block the pipeline and valve body; 4. Too much sludge cannot adjust the oil pressure, resulting in the problem of gearbox mounting. If there are only a few gears that are difficult to hang, it means that the gear in the gearbox is seriously damaged, and it is time to change.

If it is difficult to hang all of them, it is caused by the clutch disengaged not well tomorrow morning. The gear of the truck is really not very easy to hang, you can use the two-foot clutch to try to hang the gear, if it really can't be hung in, it may be a problem with the clutch release bearing and compression.

The new car in March, the most suspicious of the recent problems, the vehicle is difficult to hang in when the gear is started, it is difficult to get into the posture of the person who knows the signs of elimination, and after running dozens of kilometers and then returning to normal, every day.

Dear, your situation is a fault caused by the high temperature in the gearbox, please go to the auto repair shop for inspection and maintenance.

It must be that the clutch plate is thin, the pressure plate is pressed forward a little, and the clutch is loosened a little, so it is difficult for you to step on the end or hang the gear, that is because the clutch in it has not been completely separated. It is recommended that the landlord should find a time to go to the repair shop to see, otherwise the pressure plate will be worn out after a long time.

1. The new car gear is jerky.

The car I just bought back is difficult to gear because some gear parts of the new car are more jerky, and the new car needs to be run-in. and other gearboxes for new cars.

It would be good if the parts reached the run-in state.

2. Change the transmission oil.

The transmission oil also needs to be changed in time, if the transmission parts are short of oil, there will be a jerky situation of the gear. Transmission oil is similar to engine oil in that it lubricates gear components. The gearbox is short of oil and replenishes the oil in time.

3. It is difficult to hang up in cold weather.

When the car is cold in winter, the general gear driving is more jerky, and the transmission oil is not lubricated when the car is cold because of the cold weather. Therefore, it is normal to feel frustrated sometimes when the cold car is in gear.

4. a clutch.

The pressure plate is deformed by the silver transmission plate.

The transmission plate of the clutch pressure plate assembly is deformed due to some factor, and the solution is to replace the clutch pressure plate with better quality of the original automobile.

5. The clutch separation is not enough.

If it is a clutch failure, the clutch separation distance is not enough, resulting in the clutch separation is not completely difficult to hang the gear, in this case, go to the repair shop for repair, adjust the clutch separation distance.

6. Gear stop lock.

Because the clutch gear self-locking force is very large, it is particularly difficult to bring the car to the gear. In fact, you can adjust the gear lock and clutch cable, some car owners will not repair it, you can go to the repair shop to adjust.

Summary. Hello, the truck stall is not easy to hang, the relevant reasons and treatment methods are as follows. The first is this phenomenon caused by incomplete clutch separation, first check the clutch master pump and sub cylinder.

The second situation is that the clutch pressure plate and clutch plate of the vehicle are aged and worn out, and this phenomenon needs to be replaced with a clutch three-piece set. The third situation is caused by the wear and tear of the gearbox gear mechanism or the internal related gears, which needs to be checked for the gear mechanism and internal gears.

Hello, the truck stall is not easy to hang, the relevant reasons and treatment methods are as follows. The first is this phenomenon caused by incomplete clutch separation, and the clutch master pump and sub pump are first checked by the limb source. The second situation is that the clutch pressure plate and hungry clutch plate of the vehicle are aged and worn out, and this phenomenon needs to be replaced with a clutch three-piece set.

The third situation is caused by the wear and tear of the gearbox gear mechanism or the internal related gears, which needs to check the gear mechanism and the internal part of the gear.

Filing can be that there is no time and space in the entry and neutral space.

Then this is the key point to check the gear mechanism to see if the gap is too large?

Summary. The bad gear of the truck is caused by damage to the gearbox synchronizer and wear of the gears inside the gearbox. There is a failure in the shift mechanism of the manual transmission, a failure in the three-piece set in the clutch system, wear out of the separation bearings, wear of the clutch plates to the limit, damage to the pressure plate, etc., it is recommended to go to the repair shop for maintenance.

The bad gear of the truck is caused by damage to the gearbox synchronizer and wear of the gears inside the gearbox. The shift mechanism of the manual gearbox has failed, the three-piece set of lead Jiansong in the clutch system has appeared, the separation bearing is worn, the clutch is worn to the limit, the pressure plate is damaged, etc., it is recommended to go to the repair shop for maintenance.

What is the problem that 5th gear and 11th gear are not good to hang.

You land finch is so durable, according to your description, 1The problem of clutching, repairing the clutch, has nothing to do with your operation. 2.

It's a problem with the synchronizer! Because the gearbox needs to rely on the synchronizer to change gears. If the synchronizer is seriously damaged and loses the ability to synchronize, then it is easy to make teeth when the gear is hung.

Or rather, it's not easy to get into gear.

The other gears are easy to hang.

Your two gearboxes are partially broken (gearline). If the gear part is broken, replace the corresponding parts.

The difficulty of the truck to gear is a problem with the synchronizer. Gearbox.

Gear shifting needs to rely on the synchronizer, if the synchronizer is badly worn and loses the ability to synchronize, it is easy to get into gear, or it is difficult to get into gear.

Shift gears should keep in mind the principle of "accelerating first when gearing up, decelerating first when downshifting", press the throttle before increasing the gear to lift the speed first, and close the throttle before reducing the gear, so as to reduce the speed first. When shifting gears, try to use the "two-foot departure method", and when adding gear, follow the "step on the clutch and pick up the neutral gear".

step on the clutch and hang the high-speed gear", and quickly press the two-foot clutch pedal, which can easily increase the gear.

Transmission FAQs.

The main defeat is that there are three problems in the following three aspects, which will lead to the car being difficult to gear. Clause.

First, the gearbox oil is old and needs to be replaced, if it is not replaced in time, it will lead to a decrease in its lubrication effect, which will lead to a bad gear of the car.

Clause. First, the transmission oil is old and needs to be replaced, if it is not replaced in time, it will lead to a decrease in its lubrication effect, which will lead to a bad gear.

Clause. Second, the parts in the gearbox of the new car do not reach the best run-in state, resulting in the car is not good to keep in gear, and this situation is naturally good for a period of running-in.

Clause. Third, the temperature is low, the gear oil adhesion in the gearbox can not reach the best state, and the lubrication effect is reduced, which leads to the car is not good to slow down the dust and hang the gear.