How to maintain a lone wolf yoyo, how to maintain a lone yoyo

Lone wolf. Plastic metal is global, and the performance is quite good; The outer ring cover can be disassembled and assembled, and different cover pieces can be assembled into different shapes.

Although the newly purchased yo-yo is already equipped with yo-yo rope, the characteristics of the yo-yo are different due to the installation method, twist, etc., and it needs to be adjusted when using it. In addition, the yoyo rope needs to be replaced if it is disconnected or damaged, and the steps are as follows:

Release the tip of the yoyo rope;

Spread out your hands to form a larger rope loop;

Slip the yoyo into the rope loop. There are two schemes:

Placing the yoyo directly into the split rope loop, this set is easy to idle and suitable for advanced players;

Wrap the rope around twice and then slip it into the yo-yo, which is difficult to idle and suitable for beginners.

Wrap the rope around and shrink the loop until it wraps around. When tightening the twist, turn the yoyo so that it rotates in the direction you want to twist.

Yoyo rope knotting method.

After the length of the rope is determined, the size of the loop can be easily adjusted with the knotting method introduced below, and it can be tightly fastened regardless of the size of the fingers. Fold the rope into two strands and tie them together. Grasp both ends of the rope and pull firmly to prevent it from coming loose. Thread the rope through the loop.

Place your finger in the loop and tie it between the first and second joints of your middle finger.

The winding method of the yoyo rope.

Wrapping a yo-yo rope with a bearing type by hand is often not possible due to slippage. You can place the base of the rope on the edge of the yo-yo and hold it with your left thumb, roll it 4 to 5 times, then release your thumb and roll the rope as usual. Or hook the rope with your thumb and roll it, try to throw it once after each roll, take it back as a rewind, and then you can play all kinds of tricks to your heart's content.

You need to lubricate the bearings (including the side shafts) every few days, and replace the strings if they are dirty or old, otherwise the strings may break when playing with the ball.

Yoyo's maintenance is very important for Yoyo, if the maintenance work is not done well, Yoyo's life will be shortened, and it may also make Yoyo's operation and idling time not long.

The user can't do some fancy things, and may even hurt himself, so take care of it.

is required. Lone wolf belongs to ball bearings, and maintenance should be done by choosing different maintenance fluids for different problems.

Grease: Covering the friction surface, it can isolate the contact between water, moisture and other harmful media and the metal, so as to reduce corrosion and wear, prevent rust and protect the metal surface.

Lubricating oil: It can form an oil film on the surface of the machine, and it is between two parts that are in contact with each other. As a result, the movement between the two becomes easier, smoother and faster, and the damage caused by friction is greatly reduced.

Maintenance oil: In order to give full play to the performance of the yo-yo and the perfect reproduction skills, it is very important to maintain the yo-yo! Different types of yoyo have slightly different methods of care and maintenance.

Of course, when Yoyo can't rotate, you should consider whether the bearing has no oil, and when the yoyo makes a strange sound, you should also consider the bearing maintenance oil.

There is also a lone wolf is a metal ball, which should be kept in a dry place to prevent rust. Rust can greatly affect a good golfer's play.

Hehe, that's it.

The maintenance method is the same as that of ordinary ball bearing yoyos.

The way to wash the bearing first is: please prepare the above things first.

The jar that says "ZIPPO" is fire engine oil, which is used to clean bearings, the reason for choosing it is easy to find and the effect is very good, it can generally be found at the high-end fire machine or tobacco counter of department stores, but other appropriate items can be used to clean it, but WD-40 is said to corrode the bearings, use with caution. (The spout of the ZIPPO fire engine oil is generally white, if you see the red spout of the ZIPPO, it is likely to be a fake).

And on top of it is a cylinder of film, which is to hold the oil, and the cleaning process is also carried out in it, of course, you can find other similar utensils to replace the coarse Lu Dai.

The utility knife is the tool I use to remove the bearing shield, but there are other alternatives.

The other tools are secondary, the tweezers are used to clamp the bearing, of course, you can use your hands, and the vice is to remove the yo-yo bearing.

First of all, we removed the bearings of the yoyo, and if it was a yoyo of yoyojam, we had to use the vise.

When we generally wash the bearing, we will remove the dust cover of the bearing, so that the cleaning can be completed quickly.

Generally, the spring retaining ring is "cut" first

Pick out the spring retaining ring, and it's basically over, and the dust cover can be picked out easily, and if you are skilled, this thing is very simple.

If you do it beautifully, it is possible to attach the dust cap and retaining ring to the bearing after washing.

But if the bearing does not have a spring retaining ring or the spring retaining ring is too difficult to pick, we will directly destroy the dust cover, if the dust cover is too hard, you can replace the tool.

The dust cap can be deformed by prying it from the inner ring position, and can be extruded together if there is a spring ring.

Now you can put the bearings inside the film cylinder.

Then start pouring in the fire oil (it is recommended not to smoke during this process).

until the bearings are covered.

Then close the lid and shake it a little (don't panic if the oil is shallow on your hands, as it is very volatile).

Take out the bearing, hold it up with tweezers, and try it by flipping it, and by the way, shake off all the oil inside.

Or take it out and set it aside until the oil evaporates.

This process is over, so let's put it back on yo-yo and try the effect.

Generally speaking, it is enough to wash it once, and if it is dirty, you can wash it again.

The bearing that has just been washed can be a little uncomfortable, which is normal, and everything that moves has a run-in period. After running-in, the bearings will be smooth. Then drop a few drops of lubricating oil A, and the air ** Ranye will be fine.

Just use some maintenance oil. It's sold in supermarkets, and it's usually 18 yuan!