How to put wall covering on the Ozon board?

The wall cloth is pasted with Osson boards.

It is also very strong, but it must be laid in the right way to ensure the effect. First, clean the foundation of the wall, and then scrape the putty.

After the wall is all dry, then polish the wall to make the wall smooth and clean, and then apply a layer of base film to protect the wall from moisture, play an anti-alkali sealing role, and make it easy to break the wall cloth when replaced in the future.

If the wall has been coated with latex paint.

A layer of floor paint must be applied before applying the wallcovering. Because latex paint is easy to absorb water, the wallcovering cannot be adhered to. The concentration of floor paint is one set of floor paint plus two barrels of thinner.

Before pasting the wall cloth, it is necessary to clean up the sanitation of the site, because the area of the wall cloth is large so as not to get dirty, and the knife for cutting the wall cloth is best to use an imported utility knife.

When touching a silk head, don't pull it by hand, but cut it with a knife. Open the packaging of glue powder and special glue for wall covering, pour 2 kg of special glue for wall covering into 2 kg of water and stir it with a machine until it is slurry. Remember that the glue of the wallcovering must be thicker than the glue used for the wallpaper to enhance the viscosity, in order to protect the wallcovering and the quality of construction, the glue is best to use special glue, two kilograms of glue can be pasted with 20-30 square meters of wall cloth after adding water.

The wallpaper glue is painted on the back of the cut wallpaper with a brush, special attention must be coated with glue around the edge to ensure the quality of construction, the painted wallpaper, the glue is folded and placed for 5-10 minutes (note, no external force shall be applied, so as not to crease the wallpaper, especially the cloth) so that the glue can be posted after completely penetrating the bottom of the paper, and several pieces of wallpaper are painted each time, and posted in order. Generally, the first wallpaper is posted from top to bottom by the door or in the dark corner, and the wallpaper is gently scraped with a scraper from top to bottom, from the inside to the outside, and the bubbles and excess glue are squeezed out to make the wallpaper flat and close to the wall.

Cut off the excess wallpaper at the upper and lower ends, and the knife edge should be sharp to avoid burrs, and cut some wall cloth.

It is best to use a Japanese imported blade that sells for a piece of the market. Then use a sponge dipped in water to completely wipe the glue remaining on the surface of the wallpaper to avoid the wallpaper from turning yellow, after the wallpaper is dry, if there are bubbles on the surface, cut it with a knife and inject the glue and then flatten it to eliminate it (it is better to use a syringe).

When pasting the wall covering, clean the wall, and then choose glue to put the wall covering.

1. Check that the wall surface should be clean and flat before paving, and the surface of the wall skin should not loosen and fall off.

Second, use special tools for pasting wallpaper or other wall coverings, among which it is good to choose professional imported wallpaper knives.

3. Roll and brush the wall base film on the wall first, and adjust the seamless wall cloth glue in proportion. Note: 2 kg of glue is added in batches with a total of 2 5 kg of water.

Stir well without adding water at a time. The second time start adding 0 5 kg of water, stirring well. Add 0 5 kg of water for the third time and stir well.

Add the remaining water for the fourth time and stir well. A bucket of glue can be glued 25 to 30 square meters.

Fourth, after the base film is dry, start to brush the wall cloth glue from a certain corner of the wall, and generally start to paste the wall cloth after the roller brush a wall (roll up and down evenly).

5. Place the wall cloth along the wall, the upper height is the same as the height of the wall, and the lower end uses an item to pad the whole roll of wall cloth on the baseboard.

Sixth, the wall cloth is rolled with a scraper to scrape the wall on the wall, the order is from the inside to the edge, the wall cloth up and down after the wall cloth is pasted up and down, and then continue to pave in order.

7. If the yin angle is straight, the above rolling construction can be continued without cutting. If the yin angle is not straight, lap cutting can be carried out at the yin corner.

8. If the two cooperate with the speed, the speed is faster, you can measure the length of the yin angle to the yin angle, leave a little room to cut the cloth after the two people straighten the two ends from top to bottom, from the inside to the edge of the scrape.

9. Use a clean, wet towel to wipe off excess glue.

10. After the whole house is pasted, a comprehensive inspection is carried out, and it is found that there are bubbles and bubbling can be solved with a household steam iron.

Summary. Hello, glad to answer for you. It can be attached to the wall covering.

If the wardrobe of the Ousong board table wants to be pasted with wall cloth, it is completely okay. A lot of people like wall coverings. Then the side sealing board of the large wardrobe is also attached to the wall cloth, which has a special sense of unity from the overall effect.

It will also work well. Therefore, the side sealing panel of the large wardrobe is completely fine with wall covering. And it will also work just as well as the walls.

So post it if you want. Hope mine can help you.

Hello, glad to answer for you. It can be attached to the wall covering. If the side sealing board wants to use the wall cloth, it is also completely okay.

A lot of people like wall coverings. Then the side sealing board of the large wardrobe is also attached to the wall cloth, and from the overall effect, it is particularly integrated and shouts. It will also work well.

Therefore, the side sealing board of the big slippery filial piety wardrobe is completely okay with wall cloth. And it will also work just as well as the walls. So post it if you want.

Hope mine can help you.

The background wall of the sofa is relatively large, can it be pasted directly?

OK. How to deal with the gap between a few Osson boards.

Fill the caulking paste into the gap between the plate joints, press and wipe it densely, the thickness should not be higher than the board surface, and then paste the seam paper tape (or corner protection paper tape), scrape it flat and compact with a spatula, and there should be no bubbles between the paper tape and the caulking paste. Ensure that the middle line of the seam paper tape coincides with the Li hunger line in the seam of the board, and apply a layer of caulking paste on the paper tape with a thick return stool, and the width should not be less than 50mm from the edge of the board.

Osson board is a building material made of concrete, which is often used for exterior or interior wall decoration. The decoration of the walls of the Ozon board allows the house to show the original and natural beauty. The following is an introduction to some decoration methods of Ousong board wall.

1.Coating: Ozon board does not require additional painting because it is natural and aesthetically pleasing. However, if desired, it can be applied with a translucent, transparent or natural shade of paint to preserve the original natural feel.

2.Tile: Ceramic tile can effectively protect the Ozon board, and at the same time, it can also increase its aesthetics. You can choose marble, small fluorite or stone tiles to decorate.

3.Wallpaper: Wallpaper can change the appearance of the wall surface of the Ozon board. You can choose wallpapers with wood grains, flowers, or other natural patterns to add a sense of nature.

4.Gypsum board: Gypsum board can be used to fill the gaps of Ousong board, and at the same time, it can also play the role of heat preservation and sound insulation. Drywall can be used to decorate a room, creeping corners, or walls.

5.Surface decoration: Surface decoration can be used in a variety of ways to show the natural beauty of Ozon boards. For example, you can use plants, stones, flowers, etc. to decorate the Ozon board to make it more natural.

In short, as a natural building material, Ousong board already has a high aesthetic value. Therefore, when decorating the walls of the Ozon board, Kai should not only pay attention to aesthetics, but also to maintain its original feel. Whichever method is used, it is important to ensure that it is natural, beautiful and durable.