In life, how to install windows at home to ensure that there is no leakage?

If you want to install it to ensure that there is no leakage, then you must apply latex paint to air dry it for 4 weeks, so as to ensure that there is no leakage, and the use time is relatively long, especially durable, and the effect is also very beautiful.

After the installation of the windows at home, be sure to fill the gaps in the frame with sealant. Then do a rainwater test, and after doing so, the test will check and fill in the gaps, which will basically ensure that there will be no water leakage.

First of all, the interface should be completely sealed, and then the outside should be coated with a layer of stucco to ensure it.

The gap between the wall and the window is generally filled with styrofoam after the window is installed, and then the surface is sealed with weather-resistant sealant, which is such a waterproof measure. The leakage is basically caused by how long it takes. Exterior wall waterproofing is also only used around the window, first clean the outer window sill and the base layer on the left and right, so that the base is clean, solid and flat, clean the gap between the window frame and the hole, and then use the plugging treasure to fill the gap, after drying, and then apply waterproof glue.

The treatment method for the cracking of the connection between the window and the exterior wall is that you can use the same method above, first paint the window with water without leakage, and wait for the water to dry thoroughly with glass glue or structural glue to evenly coat the surrounding circle, and there is also a way to use some gaps on the net but the sand ash dry shrinkage has produced new gaps, although there are putty masters will also plug such gaps, but there will still be dry shrinkage to produce gaps, and the putty is not waterproof and absorbs water, so the best sealing of the contact part between the window and the wall.

Solution: If there is a gap between the window and the window frame, you can fill the gap with waterproof mortar or styrofoam, and at the same time apply waterproof sealant on the inside and outside of the window; On the one hand, the window seeps water, and the sealant on the window is aging, and the glue is separated from the wall. Rainwater seeps in.

So check and then re-apply the sealant. In addition, it may be more serious that the wall is deformed, or the window is deformed.

Water leakage caused by damage to the waterproof layer of the wall near the window: In older houses, the waterproof layer of the wall around the window is damaged and prone to water leakage; In addition, when the old house is renovated and replaced, the window is not professionally removed and the waterproof layer of the exterior wall is damaged, if there is no timely repair of water materials, the use of waterproof materials to absorb water vapor in the air after rapid expansion and various materials have huge adhesion and sealing and seepage characteristics, quickly fill and track the gaps and holes, in order to achieve the purpose of waterproof leakage around the window frame.

Generally speaking, there are two reasons. First, the installation is not designed in strict accordance with the standards of the rain line, which may be to occupy more space. The second is that the installation process itself is unqualified, such as the insufficient amount of glue, and the material problem encounters the weather heat expansion and contraction and so on.

The gap behind the window was not filled. Windows are generally installed and fixed with expansion screws, and the gaps need to be glued, and if there is water leakage, the gaps are not glued.

The main reason for the leakage of the window is that the gap in the whole window is not installed, and then there is a leakage, in this case, we must pay attention to pasting it with some corresponding things.

There are many reasons why windows leak, and there are a few points to sum up.

1. Cracked window corners: window corners are weak points, and if they are not reinforced, they will often crack due to the sinking of the foundation and structure. When it rains, the rainwater hits the walls and penetrates into the room through cracks.

2. Leakage of exterior wall decorative surface: there are also exterior walls with tiles and real stone paint. Although it looks hard and firm.

However, it is also inevitable that there will be invisible cracks that can seep water. In addition, when water penetrates into the decorative surface and reaches the block wall, if the wall is not waterproof, it is easy to leak.

3. The slope of the window sill is not enough: as you know, the position of the window sill needs to be made as an outward drainage slope. Silt accumulates on the edge of the window frame to prevent water leakage.

However, in fact, due to the insufficient slope of the window sill, the window sill is covered with mosaics and small-sized tiles, and the sprinkling is slower, and the problem of water accumulation is also common. These problems pose a danger of water leakage.

4. Unsealed window frame and wall joints: Unsealed window frame and wall joints are the most common problem of water leakage. One of the main reasons for this problem is that many owners remove and replace the windows installed in the original civil construction stage during renovation.

Water leakage often occurs when windows are removed, and the reason is the installation technology. Windows installed during the general renovation phase are filled with foam rubber at the joints of the window frames and walls.

This foam rubber is unevenly filled, which means that foam rubber is only applied in a few places with large gaps within a window frame. Its function is to fill the inside of the aluminum, which is only convenient for the edge of the window frame to be putty in batches, so this foam rubber will not play a waterproof role. Comparatively speaking, the windows in the civil construction stage are filled with cement mortar, which is much better waterproofing.

In addition, since the replaced windows are not waterproofed with foam rubber, their waterproof structure can only be waterproofed by installing a ring of sealant, that is, glass rubber, on the edge of the window frame. If the seal is aged or does not bond to the wall, cracks may develop and cause water leakage.

If there is a leakage of the installed window, it should not be filled with a lot of sealant, and you can buy a bottle of glass sealant to fill the gap again, so that the problem of window leakage can be effectively solved.

I think the reason for the leakage of the windows installed at home should be caused by the cracks in the windows that are not installed properly. For these leaks, we must deal with them in time, find out the places that are not installed well, and repair them in time.

Water seepage on the walls around the window is due to differences in materials, partitions, and gaps that cause water seepage. This phenomenon is common in both old and new houses, and there is never a problem with water seepage when measuring the interior of the windows. Frame.

The inside is designed with waterproof strips and external holes for water infiltration, the only problem is the contact point between the window frame and the wall. The solution is to go to the paint shop first to buy waterproofing glue, then clean up the leak before doubling the waterproofing adhesive card. That's it.

It's because the gap between the window and the edge of the window is not properly treated. You can find a professional window maker and add some beautifully sewn strips to avoid this situation.

If you change it to a new one, it won't leak if it's blocked.

The treatment method of window leakage should take corresponding measures to solve it according to the specific cause of water leakage. Specifically, there are three causes of window leakage:

1. The contact part between the window frame and the wall is not tightly sealed.

Solution: If there is a gap between the window and the window frame, you can fill the gap with waterproof mortar or styrofoam, and at the same time apply waterproof sealant on the inside and outside of the window;

2. The sealing strip or sealant of the window glass is not tightly sealed.

Solution: Replace or re-apply sealant to the sealing strip;

3. The sealing strip on the window frame is defective.

Solution: Replace the sealing strip again;

4. The contact between the window sash and the window frame is not tightly sealed.

Solution: Readjust the hardware hinge of the window.

To solve the above related problems, it is best to find professional personnel to solve them.

Pretending to be rainy... Re-sealant on the outside...

Buy a bag of water that does not leak, mix it with water, and wipe it on.

Buy some glass glue to fill in the gaps.

Is it the top floor, if it's the top floor, look for the property, not the top floor with the gun that can make foam.

Just apply a layer of waterproof sealant to the junction of the window and the wall.

A leak in my house would be stuffy. One area that often appears and that is expected in many homes is the leakage of our windows. The window sill leaks, and the window sill we see is wet underneath, but there may be two specific reasons for the leakage.

The first is a leak from the window itself, and the second is a leak around the window frame. So if we want to solve the leakage of the window sill, we have to work on these two points. Let's analyze the causes and solutions of window leakage.

The first point is that the drain on the window is blocked and the water cannot be removed, and then it is left along the window sill, and the window sill is leaking. If you notice a leak on the window sill, you can open the window and make sure that the window frame is full of water. At this time, through the inside, the water looks filled and overflows.

The second point is to check various places such as the window frame itself and the sealing of the glass. That is, to inspect the windows carefully. Let's see if the window is leaking, where there are steel joints in the window, where the glass is sealed, or if it is leaking due to tight sealing.

The third point is to check the part where the window is tangent to the wall, that is, the part where the window frame is tangent to the wall, to ensure that there is no water leakage. Window sills are leaking, mostly due to this reason, and we need to check carefully. The first scenario is that if the window frame itself is found to be leaking, the window drain will be blocked.

When it rains, the rainwater does not drain smoothly and then overflows, and the windowsill leaks.

The windows themselves are leaking. These include the sealing of the steel and glass of the windows. The inspection method is also very simple.

If there is a leak, I look closely inside the window to see if there are any signs of water flowing on it. If the water keeps flowing down the window and you find that the windowsill is wet, it is a leak from the window. At this time, we should also find a window manufacturer, or find a company that specializes in repairing doors and windows to repair.

Water leaks in the area where the window frame comes into contact with the wall. The causes of this leakage are caused by irregular window settings. We know that when installing windows, sealant is usually applied between the window frame and the wall, the crack mortar is carried with a waterproof road, and finally the structural weathering glue is applied to deal with it.

Many manufacturers do not apply sealant at the time of installation, but instead apply cement mortar or direct sealant. This way, if there is a slight gap in the sealant, water will seep in. The solution is to double-check the sealant outside the window.

Usually somewhere in the sealant the adhesive will be opened. Finding the part where the glue is open, removing the sealant there, and then applying the glue will basically solve the penetration of the window.

Pay attention to: glass glue firm, glass glue age, window sill water, window groove water, exterior wall waterproofing. Window leakage is often not paid attention to the age of glass glue, the durability of each brand of glass glue is different, choose a long durability time, the window is not easy to leak.

Window leakage is sometimes not the problem of the window, but the water leakage caused by the failure of the exterior wall waterproofing, and redo it.

If the window leaks, you can use glass glue to seal the window. Some time ago, the windows in our house were also leaking, and then my dad used glass glue to put a layer of glass glue around the window, so that the sealing was much better, and there was no air leakage. Of course, if you don't know how to deal with it, you can also find a professional to do it, I don't know how your property is, if you really have a problem, you can also find the relevant personnel of the property, we have a person who is responsible for the maintenance of the property.

What needs to be done is to choose good windows, choose the most expensive windows, and there can be no cracks in the process, and when it rains, it can also avoid water leakage, which will lead to a lot of water indoors.

1. When the weather is sunny and the original stagnant water is confirmed to be dry, remove the glass and paste a tile on the window sill again (note that when pasting tiles, you must stick an outward inclined slope, and if there is water, it will flow out directly).

2. Re-apply glass glue at the joint between the tile and the window frame, and then install the glass.

3. Without affecting the stability of the window, make the drainage hole slightly larger, and the lowest point of the drainage hole must not be higher than the window groove, otherwise there will always be water in the window groove.

4. Clean up the dust and residue in the window groove regularly. (especially the location of the drain holes).

I think when solving these things, we must pay attention to the size and seams of the window, and secondly, it is better to use some transparent glass glue, and at the same time, we should also use some glue to re-glue a layer of glass.