Don t knock on the tile to do waterproofing, is it reliable to do waterproof without knocking on the

The bathroom does not knock on the tiles to do the waterproofing method.

It is unreliable not to knock on the tiles to do waterproofing.

Do not knock on the tile to do waterproofing is only to apply a layer of waterproof material on the surface of the tile, and does not solve the problem of water leakage, which will cause the tile to be soaked in water, which will seriously affect the service life of the tile, and it is more than worth the loss, so it is not recommended to carry out waterproof construction without knocking on the tile.

Knocking on tiles is a relatively easy method

1. Before knocking on the tiles, we must first prepare relevant tools, such as impact drills and ladders, compared with traditional knocking tile tools, the efficiency of impact drills and knocking tiles is much higher, and the ladder can help us knock down the tiles on the wall.

2. We need to disassemble some bathroom supplies, such as mirrors, wash basins and water heaters, ceilings and bath bombs, but it is best not to dismantle the toilet first, otherwise when we knock on the tiles, the tiles are likely to fall to the ground and smash the drain.

3. When knocking on the tiles, we have to knock them from the bottom to the top, otherwise we will knock the tiles down and pile them on the ground, which will cause the tiles on the ground to be more troublesome. And when knocking on the tiles, the waterproof layer of the old hall does not need to be knocked off, and it can be done directly on the old waterproof layer when the new anti-dress trapping water layer is laid.

4. After the tile is knocked out, we have to transport all the construction waste materials out, so that the construction of the new waterproof layer can be carried out.

The waterproofing of the bricks without smashing is unreliable, first of all, we must analyze the severity of the leakage in the bathroom

1. If yesSlight water leakageIf you use the bathroom without smashing bricks, the waterproof coating is very reliable.

2. If the bathroomThe leakage is stupid and rottenIf you don't smash the brick waterproof, you need to smash the brick open, and then repair the pipe leakage, so that you can really solve the problem.

It is okay not to do tile waterproofing, but it is not recommended.

Waterproofing coatings must be applied to a clean, firm, flat substrate to create strong adhesion. Applying waterproof paint directly on the tile can not really achieve the effect of waterproofing, because there is a layer of enamel on the surface of the tile, and the waterproof layer is easy to fall off on the surface of the tile, and it cannot be firmly bonded with the base layer. There is a kind of waterproofing agent on the market that advertises "waterproofing and impermeability without smashing the floor tiles".

It's not actually a waterproof coating. It needs to be mixed with cement, concrete, which is an additive. It does not have the function of waterproofing, but as long as it is mixed with cement and mortar to increase the density of cement, the waterproof effect can be achieved.

However, it is a kind of rigid waterproofing, and it is easy to crack after a long period of rigidity. In order to completely stop the leak, the decorative and protective layers must be removed. Therefore, in order to achieve a better waterproof effect and avoid water seepage and leakage in the later stage, waterproof protection measures should be taken under the tile.

Is it reliable to do waterproofing without knocking on tiles? Waterproofing construction points.

Waterproofing construction points.

1.Do a good job of the bottom **.

Before waterproof construction, the bottom layer of the wall should be treated, and the appearance of the bottom layer should be solid, without chalking, peeling and bulging. The underlying surface must be cleaned together without any debris and stains such as dust, strippers, etc., that affect the adhesion of the coating. And the appearance of the bottom layer should be flat, with no major defects and no obvious patch marks.

The treatment method is generally to carefully clean the base surface, remove floating dust, remove cement blocks and loose bottom layer; After hydropower transformation, special treatment should be carried out on the pipe roots, drainage holes, yin and yang corners, wall hollows, etc., and the yin and yang corners should be brushed into an arc shape (or V shape). After treatment, brush the base surface with a brush, dilute an appropriate amount of waterproof paint into milk, dip the diluted material from bottom to top with a roller, and then paint the waterproof surface on the wall to achieve the effect of thorough dust removal.

2. Paint with waterproof coating.

Generally speaking, the height of the waterproof brush can be set according to the demand. Generally speaking, the waterproof height of the bathroom is 180cm, and the waterproof coating of the non-shower wall should not be less than 35cm in principle. However, in order to enhance the waterproof effect, it is recommended to be 180cm high.

In addition, regarding the lightweight walls and self-built lightweight walls of toilets and bathrooms, it is advocated that the waterproof height should be at the top. It is necessary to brush thick waterproof paint in accordance with the national acceptance standards.

Different waterproof coatings are applied differently. However, when painting, it is similar to ordinary liquid paint, from the bottom to the top, first on the wall and then on the ground. When using, if there are air bubbles in the slurry, the air bubbles should be brushed off, and no air bubbles are allowed.

The need to draw only one direction at a time and the opposite a second time. The interval between the first and second brushing should be around 4-8 o'clock.

3.Do a closed water experiment.

The closed water test is an important test method to check the indoor waterproof quality. After the waterproofing project is completed, seal the door and water outlet, and fill the room with water to a certain level. If there is no significant drop in the liquid level within 24 hours, it is qualified.

After the closed water test is completed, make another layer of cement mortar protective layer on top of the waterproof coating layer, taking care not to damage the completed waterproof coating layer. After the protective layer of cement mortar is dry, you can lay wall tiles or spray paint for normal decoration.

Is it reliable to do waterproofing without knocking on tiles? Waterproofing construction points.

It is reliable to do waterproofing without knocking on tiles, and there are waterproofing agents on the market that do not need to knock on tiles, which are easy to use and cheap. When using, pay attention to keep the surface of the core tile dry, clean up the dirty things in the floor tile joints with a scraper, and then plug the floor drain with a plastic bag, and slowly pour it in after diluting the waterproofing agent.

Generally speaking, it has nothing to do with whether the water leaks or not, because most of the reasons for water leakage are due to pipe rupture problems, or connection problems between pipes. Of course, the purpose of the tile is to check whether there is a crack in the tile or the inside is empty, and it is also to prevent it from being troublesome to use in the future, but it doesn't matter if you don't knock it.

At present, there is a waterproofing agent on the market that does not need to knock on the tile, and the cement surface can be directly filled with the gap, which is a more convenient and fast method, and it will not be very expensive. When using, pay attention to the surface if it is dry, if there is dirt or other debris on the surface, it will also affect the future performance, and from time to time to clean daily.

When using, first clean up the dirty things in the joints of the floor macro hand bricks with a scraper, and then plug the floor drain with a plastic bag, and then dilute the waterproofing agent with three times the water and slowly pour it into the floor tile, slowly wait for it to leak into the floor tile, and then sweep it with a broom several times to make sure that it has flowed in evenly, and finally ensure that it is fully clean.

Waterproofing can be done without knocking on the tiles, but it needs to be treated with materials such as waterproof paint or waterproof membrane. The tile itself is not waterproof, it is just a surface material. If you need to waterproof the surface of the tile, you can choose to use a special waterproof paint or waterproof membrane to cover it to achieve a waterproof effect.

If your house is not self-occupied, just want to temporarily solve the problem of water leakage, and there is no problem with the embedded pipe in the bathroom, in fact, it is feasible not to knock on the tile waterproof, and it does not damage the bathroom floor tiles, it can be used normally before and after construction, and the bathroom can be used normally before and after construction, but there are also disadvantages, how much material can not be used, because the mortar layer under the tile is very thick, you can't see many gaps, it may take a lot of materials to fill it completely, and it may also need to be soaked many times, and the effect of later use is unknown.

Generally speaking, I still recommend using the traditional method to waterproof and repair the leakage in the bathroom, and the correct way to repair the waterproof leakage in the bathroom is to knock off the tiles and re-do the waterproofing.

1. Toilet leakage can be repaired without smashing bricks, but it is limited to slight water leakage. If the leakage is severe, you need to smash all the bricks and re-lay the waterproofing layer.

2. If it is a slight water leakage, you can use a special waterproof paint to fill the leakage and apply it to the water leakage. If the leakage is severe, we need to lift all the bricks. Then use waterproofing paint for the last time.

3. There are a lot of waterproof coatings on the market now. One of these waterproofing products is crystal colloids applied to ceramic tiles. Not only does it not affect the aesthetics, but it also immediately solves the problem of water leakage.

Therefore, if the bathroom leakage at home is not very serious, it is as serious as rain, and there is no need to smash the porcelain rough tare bricks.

1. First find the leaking part, check whether the hose connection hose is loose, and if so, remove it and reinstall it.

2. Check the water pipe and let the master test the pressure. If water seepage occurs during the pressurization process, the water seepage location needs to be repaired or the water pipe replaced.

3. If it is not a problem of pipeline leakage, check whether the ground waterproof layer is damaged, and if so, it needs to be re-waterproofed.