The kitchen is tiled, how to do waterproofing

1. The surface of the base layer of the waterproof layer must be cleaned of dust and debris, and the residual mortar hard blocks and protruding parts on the surface should be smoothed and swept.

2. The surface of the base layer of the waterproof layer should be kept dry, smooth and firm, and there should be no defects such as hollowing, cracking and sanding.

3. In the screeding layer grounding drain, pipe root, water outlet, and sanitary ware root, the head should be smooth. The slope meets the design requirements, and the components must be installed firmly and embedded tightly. After acceptance.

4. The details such as pipe roots, floor drains, drainage outlets, yin and yang angles protruding from the ground should be supplemented with additional layers first, and after brushing the polyurethane primer, the concealed engineering acceptance should be completed after inspection and completion.

How to do waterproofing on the tile:

1. First of all, clean the surface of the tile. Generally, it is necessary to use a damp mop to mop dry, and then wipe it clean with a dry mop to ensure that there is no oil and dust on the surface.

2. Directly apply waterproof coating film on the surface of the cleaned tiles. The waterproof coating film is transparent and adheres tightly to the surface of the tile after the painting is completed.

3. When the waterproof coating film is solidified, the water can be tested at this time. That is, a closed water test is done on the surface of the tile. At this time, you can check the quality of waterproofing. If the closed water test is qualified, it means that there is no problem with the waterproof effect.

Precautions for waterproofing on the tiles.

1. Before construction, be sure to clean up the dust and stains on the surface of the tile, so as to prevent the waterproof effect of the waterproof material from being affected. In addition, it is also necessary to use a plastic bag to seal the drain outlet of the floor drain to prevent the waterproof material from flowing down from the location of the floor drain and causing blockage.

2. Check whether there is any damage to the gap between the tiles, and if so, you need to use suitable materials to repair them. In order to strengthen the waterproof effect of ceramic tiles, it is also necessary to use instantaneous plugging agents around the floor drain and toilet to prevent leakage in these locations.

What to do if the kitchen is not waterproofed and has been tiled, hello, the most fundamental solution is to pry the tiles, and then re-do the waterproofing, although it is a little troublesome but it is the safest way. Remove all the bricks first, re-level the wall, do waterproofing, and then re-til. It's not very troublesome, as long as the pin is not a water pin bucket pipe leakage, plane the ground, clean the ground and then level, you can do waterproof several times, and then do a closed water test for 24 hours, you can re-til.

I hope my answer is helpful to you, and finally I wish you good health and a happy mood again! <>

Hello dear if my answer is helpful to you, please give a like (comment in the lower left corner), look forward to your like, your efforts are very important to me, and your support is also the power of my progress. Finally, I wish you good health and a good mood!

There are four points on how to waterproof the tile.

1. Before construction, block the sewer of the floor drain with plastic bags or other items, then add water to make a gelatinous waterproof material, and then pour the mixed mixture on the ground, let it stand for about 3 hours, its material will automatically flow to the cracked place or uneven place for filling, and the waterproof layer can be formed after curing. When you're done, remember to check it to see if there's anything missing, and if so, apply it twice by hand.

Second, what should be paid attention to in waterproofing.

1. Pay attention to the waterproof height.

When brushing waterproof paint in the bathroom, you must pay attention to the height of the waterproof, because the bathroom wall is also waterproof, especially the wall of the shower area, its waterproof should be 180 cm high, and most other areas need to be 30 cm high, and the non-load-bearing light body wall needs to be 60 cm high.

2. Pay attention to waterproof materials.

The waterproof coating of the bathroom has high requirements, and it is necessary to meet the requirements of the relevant place specifications, select qualified and easy-to-use products, and not only require good waterproofness, but also have high product quality and life requirements.

3. Pay attention to details.

When applying waterproof paint in the bathroom, it is necessary to carefully paint the yin and yang corners, wall and ground joints, and the roots of sewer pipes, and it is best to apply it twice again to avoid missing parts.

Fourth, how to choose ceramic tile waterproof materials.

Environmental protection, if you choose products that are not environmentally friendly, after the waterproof layer is done, under the thick floor tiles or cement, harmful gases are slowly released. Therefore, if you want to buy waterproof materials, you must go to a regular building materials store or supermarket and choose a well-known brand.

Summary; The characteristics are not hard, generally speaking, the appearance characteristics of the waterproof coating are divided into two kinds: rigid and flexible, rigid generally refers to the cement mortar, and the flexible waterproof layer is more, the acrylic waterproof coating has good elastoplasticity, can adapt to the partial deformation of the structure, so the waterproofness is good.

Answer one question a day, and yours will answer it today.

If you don't consider tiling, you don't need to do waterproofing. If you want to paste tiles, it is so smooth, you basically can't stick it, and the bricks will fall off. Therefore, it is recommended that the wall be cleaned and then approved with a waterproof mortar, which is both waterproof and leveled, and then tiled.

Your patio floor has been leveled and it's time to start waterproofing. It is recommended that a polymer waterproof coating, a waterproof membrane is almost, and then a protective mortar, the finish is tiled, and it is estimated that it can be used for more than 15 years.

The key place came, the high part of the terrace, I didn't see the rainwater floor drain, so if it rains, this rainwater will flow down and drain away. The part of your patio that is next to the interior, you said that you are going to make a balcony, and this is correct. The waterproof difficulty is coming, that is, the waterproof platform itself, the junction between the waterproof platform and the ground and the inlet and outlet of the pipe mouth, the waterproofing of these details is relatively high, whether it is the material or the construction technology, if it is not done well, the rainwater will seep in horizontally, or even leak down.

Hello, this is not possible, the bathroom waterproofing needs to be carried out on the cement surface, it is necessary to do a good job of waterproofing first, and then to paste the tiles.

The bathroom is waterproof, the standard method is that the ground needs to be done all, the wall should be at least meters high, it is recommended to do full height, if it is a lightweight wall, then it must be done full height.

As for the material, it is recommended to use the kitchen and bathroom waterproof slurry, and the following is the detailed construction method:

1. Chisel the root of the pipe, the periphery of the floor drain and other parts that have cracks and need to be repaired into a "V" shape, clean them, and sprinkle them with water to moisten;

2. Mix the waterproof mortar with water (water-cement weight ratio 1:2 3) evenly, repair the construction before the initial setting (within 5 minutes), and make R angles at the root of the pipe, the perimeter of the floor drain, the yin and yang corners, and the roots of the wall;

3. After the final setting of the repair mortar, the powder and liquid of the waterproof slurry are stirred evenly, let stand for 3 minutes, and then stir again and evenly brush on the base surface.

Ceramic tile is a more popular repair material in the home, and is widely used in the bathroom, kitchen and other areas, mainly because the ceramic tile material is not only high hardness, but also wear-resistant, waterproof, non-slip, easy to clean, long service life and other advantages, especially suitable for the kitchen, bathroom this dirty, heavy moisture area. Although the tile has the effect of preventing water and respecting water, it is still necessary to do waterproof before construction, so how to do waterproof after pasting the tile? Let's take a look with Qeeka Home experts.

First, how to waterproof the tiles.

The tiles can be scrubbed clean first to ensure that the surface is free of dust, particles and water, and the construction can only be carried out in this state; Then mix the transparent waterproof gel and pour it on the floor tile; The waterproof gel will slowly spread along the gaps and slopes of the ground throughout the tile floor; Finally, wait for a period of time, and then perform a closed water test to test the waterproof effect.

Second, how to choose bathroom tiles.

1. The overall tone should be consistent.

Bathroom tiles are divided into wall tiles and floor tiles, when choosing, the overall tone should be consistent, preferably gray, white, black, to avoid the appearance of a more separate jumping tone, destroying the overall coordination. At the same time, it is also necessary to take into account the coordination with the tone of the sanitary equipment, if the sanitary ware products are white, then the tile should not be white, it is not good to be too monotonous.

2. Consider the light in the bathroom.

If the bathroom tile is not well matched, it is easy to produce a bad effect on the whole vision, for example, the bathroom area is small and the light is poor, it is not suitable to choose dark tiles.

3. Pay attention to slip resistance.

There is often water on the bathroom floor, if the tile surface is too smooth, it is easy to fall when in use, so when choosing, you should choose a good non-slip and concave and convex surface.

Summary: The above is about how to do waterproofing with tiles, and how to choose bathroom tiles, I hope the content shared can give you some reference, I want to know more about Qi Xi to learn more about related knowledge, you can **** Qijia information.

Hello kitchen waterproof mortar first according to the correct proportion and modulation method of the waterproof mortar modulated, and to stir evenly, when the stirring has no particle state, you can stop stirring, and then need to stand for about 3 minutes, when the stirring no bubbles appear again, you can start the next construction. 2. Apply mortar (1), first focus on painting in special areas, such as: pipe roots, floor drain periphery, corner corners, etc., and then carry out a large area of the first application on the kitchen floor, and the thickness of the coating needs to be kept within one millimeter, and the direction of painting needs to be kept all the way, so that it dries faster in the later stage and is not easy to hollow and crack.

2) In order to improve the waterproof effect, it is also necessary to carry out the second painting on the first waterproof coating, and when brushing, it should be painted in a cross way, and it must be painted evenly, and there must be no missing brush. After the painting is completed, the next day Huaisen can perform the closed water test. 3. After the waterproof construction on the wall waterproof kitchen ground is completed, it is also necessary to carry out the lead waterproof construction on the kitchen wall, and the waterproof construction height of the kitchen wall generally needs to exceed one meter eight, so as to prevent the faucet from splashing water, the wall is soaked, and the specific construction steps are the same as the construction steps of the ground waterproofing, but the waterproof coating used is different, and then it is necessary to use the waterproof coating specially used for the wall.

Tile paving is common in modern home decoration, especially in the bathroom, kitchen and other seepage land, ceramic tiles are indispensable, walls and floors should be paved with tiles, mainly because the waterproof effect of tiles is good, and these areas consume a lot of water, not only need to pave tiles, but also need to do a good job of waterproofing before that, so if you paste the tiles after how to do waterproof? Let's take a look with Qeeka Home experts.

1. How to do waterproofing after pasting tiles.

After pasting the tiles, you can use the gel waterproof material, block the drain of the floor drain with a plastic bag before construction, and then add water to the gel waterproof material for blending, and then pour the prepared mixture on the ground, stand for about 3 hours, and the material will automatically flow to the cracked or uneven position to fill, and the waterproof layer can be formed after curing.

Second, what should be paid attention to in the waterproofing of the bathroom.

1. Pay attention to the waterproof height.

When brushing waterproof paint in the bathroom, we must pay attention to the waterproof height, because the bathroom wall is also waterproof, especially the wall of the shower area, which is waterproof to achieve a height of 180cm, and most of the other jujube rental areas need to be 30cm high, in addition to non-load-bearing light walls, which also need to be 60cm high.

2. Pay attention to waterproof materials.

The requirements of waterproof coating for the bathroom are relatively high, and it is necessary to meet the requirements of the relevant site specifications, choose qualified and easy-to-use products, and not only require good waterproofness, but also high product quality and service life.

3. Pay attention to details.

When the bathroom is constructing waterproof coatings, it is necessary to carefully paint the yin and yang corners, wall and ground joints, and the roots of sewer pipes, and it is best to paint them twice to avoid some missing parts.

Summary: The above is about how to do waterproofing after pasting tiles, and what to pay attention to in bathroom waterproofing, I hope to share the content of Yanxiang can give you some reference, if you want to know more about relevant knowledge, you can **** Qijia Home to consult.