Is there any way to re lay a layer of bricks without smashing the original tiles for the tile wall?

A few days ago, a few tiles suddenly fell from the house, but fortunately they didn't hit anyone, which scared me to death! There is no problem with looking very stable during acceptance, but when the wall tiles are removed, it is simply caused by not shoveling the wall skin. I can't find the person in charge of the renovation, where can I reason?

Look at this large area of white wall skin, how can the tiles be firmly pasted, and they can't be used for a long time! Therefore, you must remember to shovel the wall skin when sticking wall tiles, otherwise you will not be able to find anyone to reason with you.

I looked for a decorator again, and they said that they wanted to reinstall, because the area was too large, but now it was inconvenient to reinstall, so they temporarily used expansion screws to do a simple fix.

Here are a few reasons why wall tiles are used for a short time and are easy to fall off:

1. The quality of wall tiles.

The water absorption rate of wall tiles is directly related to the adhesion force, but it is not that the higher the water absorption, the better, if the moisture is not enough, it will be inconsistent with the cement shrinkage, which will lead to the falling off of the tiles.

2. The grassroots work has not been done well.

Underlying questions are often the most common. When we decorate a new house, we will shovel the wall skin, but most of us simply shovel or paint the wall. However, no matter how much the wall is brushed, if the wall skin is not cleaned, it will greatly affect the friction and adhesion of the wall.

Also, the wall is not watered enough, and the tiles are not cleaned properly, which will leave hidden dangers.

3. The tile is not dry and receives bumps.

When the cement mortar has not been completely bonded to the wall and is dry, it is best not to let it be collided, which will cause gaps in the mortar, resulting in unstable paste, and it may fall off in the future.

4. Gaps between tiles.

Gaps need to be reserved between wall tiles, because the effect of thermal expansion and cold contraction will cause them to squeeze each other, resulting in fracture or falling off. The cement mortar behind the wall tiles should not be too thick, which will not only affect the overall effect of the space, but also the thermal expansion and contraction will be very unstable, which will accelerate the falling off of the tiles.

It's definitely not okay to stick tiles without smashing them, and if you replace them, you can choose wallpapers and the like.

This is not good, there will be trouble in the future, it has already cost money, and I am afraid of trouble.

No, because the tiles will not be firmly pasted in this way, which will affect the later use and reduce the space.

There are three ways to renovate old floor tiles: one is to remove the original old floor tiles. The second is to replace the damaged bricks with well-preserved floor tiles.

The third is to lay new floor tiles directly on top of the old floor tiles. For the relatively thin old floor tiles or laminate floor tiles, it is possible to re-lay the new floor tiles directly on top of the old floor tiles. However, it is not possible to lay directly on the floor tiles.

Note: When relaying new floor tiles, uneven ground areas need to be re-leveled. At this time, you can use tile surface treatment agent, mosaic adhesive, etc. to apply to the old floor tiles to paste the new floor tiles.

No, it doesn't work. The waterproofing of the house is guaranteed by the property, and it is guaranteed for at least two years.

This is definitely not good, it is best to pry the original tile to re-paste better, so that the bottom edge height will not be too high, and the stability is stronger, if directly pasted may appear hollow drum sliding phenomenon.

The original bricks are non-slip on it.

Generally, the tiles on top of the original tiles can be scraped twice with ceramic tile renovation putty, and then the tiles can be pasted according to the normal operation method. Tile renovation putty is a two-component high adhesion putty, which has high adhesive strength on the surface of new and old tiles, and is a new generation of high-quality green building materials. It is made of acrylic emulsion, added with a variety of functional additives, mixed and mixed in proportion, and is used for the first level of interior and exterior wall tile renovation.

It should be decided according to the situation on the ground, and it is recommended to go to the Oushennuo store to have a look.

If you don't want to remove the tiles and redo them, is it feasible to put another layer of tiles on top of the original tiles?

Hello, if you don't remove the original tile, you can pave the new tile, but if it is a wall tile, you can't paste the tile, because this will cause their tiles to not be strong, soon to fall, the connection between the tile and the soil is very poor, so the new tile will be easy to loosen, especially strong on the old tile, you can use a grinder to polish it, resulting in a very rough mu only when pasting on the reputation, so it will also be very strong, so that you can reduce the workload, and you don't have to be so troublesome, Remove all the porcelain, but be sure to polish it well, otherwise the new tiles will fall off very easily. Paste the new tile is also conditional, the old tile does not have the phenomenon of opening, you can paste the new tile, and there is no damage around it, or the edge is upturned to paste, the surface is very flat can be, if you meet the above conditions, it is not necessary to dismantle. If you want to dismantle it is also very labor-intensive and troublesome, so you can save labor costs, but if it is a wall tile, it will not work, because the surface of the tile is relatively smooth, and it will be very fast and slippery in gravity, and the tile will fall off.

If you don't want to smash the old tiles, but want to put new ones on the wall, you can consider the following steps:

1.Clean the wall: Use detergent and water to clean the surface of the old tile and make sure the wall is clean and free of dust and grease. You can use a brush or rag to clean it.

2.Sanding the wall: Use sandpaper or abrasive stone to sand the surface of the old tile to help the new tile adhere better to the wall. Make sure to sand the surface flat to remove any unevenness.

3.Cover up old tiles: In order to put new porcelain tiles on the wall, you can consider using a special tile adhesive or thin tile adhesive to stick the new tiles to the old tiles. Make sure to choose the right adhesive for your wall and follow the product instructions.

4.Attach the new tile: Depending on your design and layout, use a toothbrush or trowel to apply tile glue to the surface of the old tile, and then place the new tile on the glue-applied surface.

Use a tile clamp to keep tiles evenly spaced and use a tile cutting tool to cut tiles to the desired size if needed.

5.Tile adhesive curing: According to the adhesive's instructions, wait enough time for the adhesive to fully cure and bond the tiles. This may take a few hours or more, depending on the adhesive used for finger elimination.

Please note that before proceeding with the above steps, make sure that you have carefully considered and evaluated the feasibility and effectiveness of applying new tiles. If you are unsure about the operation, it is advisable to consult a professional bricklayer or renovation expert for more specific advice and assistance.

The construction method of pasting another layer of ceramic tiles on the original tile: remove the dust and dirt on the surface of the old tile, and then use the tile adhesive to do the base layer on the old tile, and the new tile can be directly pasted after the completion of the swiping. The adhesive should also be thinly applied on the back of the new tile, and the thickness should be subject to the back pattern of the covered tile, so that the new tile will be more firmly glued; When paving new tiles, use a rubber hammer to tap the new tile edge to adjust the edge, you need to pay attention to the reserved expansion joint, 24 hours later, wait for the tile adhesive to dry thoroughly, and use the grout to hook the joint.

Paste new tiles on the old tiles, the first thing to pay attention to is that the original size of the tiles must be measured first, and then buy the same size of tiles to paste, if the size is not suitable, the tiles will look a little ugly. Paste new tiles on old tiles, and you also need to pay attention to buying thinner tiles when buying tiles, otherwise there will be a feeling of unevenness.

When you buy tile adhesive, you must buy a better stickiness, because the original tile surface is relatively smooth. It is also necessary to pay attention to the old tiles and the new tiles to see if the original tiles and the new tiles are consistent, otherwise there will be a bit of a feeling of being out of place and late to chain in.

Tips for tiling

1. Dry paving method.

One of the most commonly used floor tile paving is the dry paving method, the specific method is to clean up the floating sand and debris on the ground after the base is watered and wet, and use a dry cement mortar of one to three. Then pave and paste flat according to the horizontal line, put the brick on the mortar and then use the rubber hammer to vibrate it, this paving method can effectively avoid the phenomenon of ground bricks producing bubbles, hollow drums, etc., but the first aspect is more expensive, and the technical requirements are higher.

2. Wet paving method.

Wet paving method is a practice that many families will adopt, and the difference between it and dry paving method is to replace the dry cement mortar of one to three with ordinary water and cement mortar, so this practice is easy to produce bubbles in the paving process, affecting the service life of the floor tiles.

Summary. Dear, hello, I am happy to answer for you, in the old tile in the paving of a new layer of tiles can be, this is not possible, must be removed from the previous tile, in addition to do a good job of base treatment, if pasted, there is a certain chance of hollowing, falling off this situation<>

What program is best to use.

Dear, hello, I'm glad to answer for you, in the old tiles in the paving of a new layer of tiles can, so is not the group resistance can, must remove the previous tiles, in addition to do a good job of grassroots treatment, if pasted, there is a certain chance of hollowing, falling off this situation seepage or limb <>

The surface of the old tile is relatively smooth and dusty, although the adhesive can be used, such as pasting the new tile through the tile adhesive, the effect is not particularly ideal, it is easy to cause the new tile to fall down directly, but it will cause economic losses. Therefore, it is a matter of pie orange Liang that outweighs the loss, and it is not recommended to operate like this, and you must not try to save trouble.

Hello, dear, if the original old Qisosong cave tiles have the problem of damage and cracking, we will knock them off first, and then brush the surface of the wall with surface treatment agent, and then do a leveling work before paving the new tiles. Or knock out all the old tiles, although the project is more complicated, but it can ensure that the later tile effect is better. <>

You can't put tiles on the old floor tiles.

Is it OK to glue it with tile adhesive?

No, dear, don't try to save trouble, if the effect is not good, there will be a gap or tile falling off in the later stage and it will be re-paved.

Dear, if you want to pave it, you can pave it, there is a problem to say.