Where to go for computer ash cleaning and silicone grease, how to clean silicone grease

As long as you unscrew the two screws behind the case, and then blow it out with a fan, you can solve it yourself, but you need professionals to change the silicone, and it is best to go to a computer store or repair shop.

Answer: You can go to the computer after-sales office, or you can go to the computer repair place.

You can go to a general computer after-sales or repair shop, or you can buy silicone grease and replace the ash by yourself.

Computer ash cleaning and silicone grease can go to some computer after-sales repair shops or machine computer stores to sell computers.

If you clean the computer and change the silicone grease, it is best to go to some well, computer repair places. Places like the computer city are generally fine.

Computer ash cleaning, silicone grease is generally on the CPU or graphics card, these locations are easy to heat.

You should go to a professional computer shop, or a repair shop, which can help you clean up.

If I change my computer to Guizhou, you can go to a general mobile phone store to complete this.

The computer is cleaned and the silicone grease is changed to **buy? You can go to the almighty **, which should be able to be bought, related finished products.

The computer is so light to clean the ash on the intercontinental? Generally, you can find their after-sales service department, then you can change it.

The regulation of computer cleaning ash is basically to go to the place where the computer is repaired.

I think that the computer should be cleaned and the silicone grease should be done in the place where the computer is repaired.

After sending it, this silicone can be carried out to carry out all the dust responsibly.

It can be bought online, and it can be bought or required at digital stores (computer stores) outside the community.

If the computer is dusted, it is best to go to another place to operate the silicone grease you replaced.

When cleaning, first we need to open the location hard drive, and then we need to use cleaning software during the gray grease replacement process.

In the process of cleaning ash and changing silicone grease, we must pay attention to the technique.

This computer cleaning is very simple, you can buy a silicone pad cleaning online.

Hello, there are generally relevant modes in the settings of the computer, you can look for them carefully.

Computer dusting, can you cut out**? I think I should go to the settings and check it, it should be able to hold up, right?

You can find a computer repair service for you to clean up and play silicone.

It should be that the function of cleaning the ash inside is wrong, so this is wrong, so this should be restarted.

If you have strong hands-on ability, you can get it yourself.

Computer cleaning and replacement. Where is the cabinet going, I don't know where to hang it, you can consult on the Internet where it went.

You can go to your local computer repair shop to change the silicone grease.

This should still be there, you can take a look at it, there are a lot of them that sell this thing, and they can handle it.

Thermally conductive silicone is also known as thermally conductive silicone. When installing a CPU or cleaning up GPU dust, you need to remove and replace the thermal grease using the method.

Remove the thermal grease that has dried out on the cup or GPU.

First of all, remove the radiator on the computer graphics card or cup, and then use a screwdriver or other hard block to scrape slowly, if it really doesn't work, use a cotton swab dipped in alcohol to wipe slowly. If you still can't wipe it off, install the radiator and let the computer run for 10 minutes to heat up the cup or graphics card, at this time the silicone grease will become softer, then shut down, quickly remove the graphics card, repeat the above steps, and generally you can erase the silicone grease. Thermal grease is made of refined synthetic oil as the base oil thick inorganic thickener, and refined with structural stabilizer and anti-corrosion additives, which has good waterproof sealing, waterproof, solvent resistance and anti-creepage properties, does not corrode metal, and has good adaptability with rubber, and is used for waterproof sealing and lubrication in sanitary equipment, sealing rings, electronic and electrical industries.

1. Do not apply silicone grease by hand. If you accidentally come into contact with **, please wipe it clean first, and then rinse it with water. In addition, if it comes into contact with your eyes, please remove and rinse immediately, and if you feel serious discomfort, please go to the hospital immediately for examination.

2. The thickness of thermal grease is about the thickness of a piece of ordinary paper. The use of thermal grease is not about applying as much as possible, but on the premise of ensuring that the gap is filled, the thinner is better. The thicker the thermal grease is applied, the more it affects the heat conduction efficiency, and the inexperienced person must pay attention to it.

3. After use, tighten it and store it in a place where the volume is dry and out of the reach of children. In addition, CPU thermal grease can also be used in graphics cards, memory, and other electronic heat dissipation modules.

Eradicate the silicone grease. The old silicone grease on the CPU has generally been denatured and hardened, and the residual silicone grease can be gently removed with a flat spatula. Care needs to be taken when cleaning the silicone grease to avoid scratching the chip.

The notebook has been used for a long time, and there will be problems with heat dissipation, which will affect normal use.

01 First turn the laptop upside down and remove the battery.

02 Loosen the screws of the largest cover plate at the bottom, remove the cover plate, and you can see the radiator.

03 Unscrew the three screws on the fan first, take out the fan and clean it.

04 There is a number next to the four screws of the heatsink covered on the CPU, and the four screws should be unscrewed in order.

05 There is also a heatsink cover on the graphics card, and there is also a fixing screw here, the logo is "5", and this screw is the last to be removed.

06 Remove the screws from 1 to 5 in turn to remove the radiator.

07 Wipe the residual silicone grease off the CPU, reapply it, and smooth it out. There is no need to paint on the graphics card chip, because this notebook graphics card is dissipated through a thermally conductive silicone sheet glued to the heatsink.

08 Then install the radiator and fan as they are, pay attention to the reverse order of screwing and dismantling, from 5 to 1.

Notebook silicone grease, do not apply too much, just a thin layer, apply evenly.

The role of silicone grease is to assist in heat dissipation, and the processor of the computer does not necessarily have to apply silicone grease, because the processor has been coated with a layer of silicone grease when it leaves the factory, so it does not need to be reapplied when it is first used. Even if the grease has been consumed, if the heat dissipation of the computer is normal, it can be left unsmeared.

Are you sure you're an authentic HP aftermarket? I'm talking about after-sales, not a place to sell machines, because I remember that there is no ash cleaning after normal after-sales, only the maintenance of the whole machine, that is, even the back cover is not opened, because opening the back cover means losing the warranty.

Silicone is generally coated with a layer of paper or what I forgot, wipe evenly, and then apply it on and wipe it to achieve complete uniformity.

Your fan is stuck, it should be that there is something inside or the fan is not installed properly. You must go to him, you must check, it is likely that the fan will be scrapped after a long time, and then it will often go black, I have personal experience around me, it is too expensive and not repaired, so I have been letting the fan ring, and the result is completely not ringing in the end, and I am happy to say that it is okay, the result is directly black, as long as the machine is turned on in the future, the screen is black without doing anything, and it is completely scrapped.

In the future, go to clean the ashes, go to the real after-sales, don't sell computers, these people don't know how many people get it every day, just finish it casually, ** is also low.

First of all, the commonly used heat dissipation grease is non-volatile, as long as the quality of the silicone grease is okay and the application is scientific, there is basically no need to consider changing the silicone grease. If you are using silicone grease that has poor thermal conductivity or is easy to dry, it can basically be replaced once a year. The circumstances that need to be replaced may be:

1. Under normal conditions at room temperature, the fan speed peaks and the CPU temperature is too high; 2. When the CPU or heat dissipation module has been replaced; 3. Disassemble the heat dissipation module by yourself and find that the silicone grease is obviously solid. To put it simply, as long as the silicone grease does not dry, there is no need to replace it, which needs to be judged by the quality of the silicone grease used.

As for ash cleaning, considering the long use time, if it has never been cleaned, it is recommended to ask a professional maintenance engineer to assist in disassembling the machine at the official after-sales service center of the corresponding brand, and detect whether it is necessary to replace the silicone grease at the same time.

Theoretically, ash cleaning should be carried out once every six months, and silicone grease should be changed once a year.