M126A paper jam, how to take it out?

1. Open. 2. Take out the toner cartridge and place it in a dark place;

3. Hold both sides of the paper with both hands, and slowly take out the jammed paper as parallel to the feeding direction as possible;

4. Put the toner cartridge back into the printer after taking out the jammed paper, and close the front cover of the printer.

There are several reasons for paper jams:

1. Too much paper is put into the carton or the paper position is not placed properly;

2. The type of media used when printing is beyond the support range of the printer.

Common Paper Jam Locations:

1. Below the toner cartridge;

2. a paper inlet;

3. Paper outlet.

1. Open 2, take out the toner cartridge, and place it in a dark place; 3. Hold both sides of the paper with both hands, and slowly take out the jammed paper as parallel to the feeding direction as possible; 4. Put the toner cartridge back into the printer after taking out the jammed paper, and close the front cover of the printer. The reasons for paper jams are as follows: 1. Too much paper is put into the carton or the paper position is not placed properly; 2. The type of media used when printing is beyond the support range of the printer.

Common paper jam positions: 1 below the toner cartridge; 2. a paper inlet; 3. Paper outlet.

HP printer m14-m17 jam how to take.

To clear the paper jam from the tray area, you need to remove the paper from tray 1 and slowly pull the paper out of the printer. For all other trays, follow the steps below. 1. Slide the paper tray out of the printer and remove the damaged paper from the paper tray.

2. If you can see the edge of the paper in the paper feed area, slowly pull the paper down and out of the printer. If the wheel can't find the paper, look for the paper in the top cover area. 3. If you can't move the paper easily, don't force it.

If the paper is attached to the tray, try removing it through the upper part of the tray (if possible) or from the top cover area. 4. Before reloading the paper tray, make sure that the paper is flat at the four corners of the paper tray and is under the tab of the guide plate. 5. Open the top cover, and then close it to clear the jam information.

If the paper jam information still shows which Tong code, it means that there is still a paper jam in the printer. Look for the jam in another location.

1. Open.

2. Take out the toner cartridge and place it in a dark place;

3. Hold both sides of the paper with both hands, and slowly take out the jammed paper as parallel to the feeding direction as possible;

4. Put the toner cartridge back into the printer after taking out the jammed paper, and close the front cover of the printer.

There are several reasons for paper jams:

1. Too much paper is put into the carton or the paper position is not placed properly;

2. The type of media used when printing is beyond the support range of the printer.

Common Paper Jam Locations:

1. Below the toner cartridge;

2. a paper inlet;

3. Paper outlet.

Try to take out the jammed paper, if you can't take it out, it is recommended to send the machine to the local service center for repair, do not go to the hard pull by yourself, it may cause hardware problems with the machine.

What printers need to pay attention to.

When the printer paper and ribbon cartridge are not set, printing is prohibited. The printhead and print roller will be damaged.

If the ink exhaustion indicator on the printer's control panel is still flashing and not working properly after following the correct steps to replace the inkjet printer with a new ink cartridge, it is likely that the ink cartridge has been replaced improperly.

1. If the paper is jammed, it is not just to take out the half of the paper stuck in the carton.

2. Many friends wonder why all the paper in the carton is taken out, and the toner cartridge is taken out, and the paper card is also taken out, but the toner cartridge is still installed and the paper is not taken out. The printer cannot be used.

3. Remember, this is a place that unfamiliar friends don't understand, open the cover behind the printer, there is a place that can be broken, after opening it should be able to see the card paper, just pull it out.

Reasons: 1. Paper jam in the paper feeding section (due to the bad paper roller, bad paper, foreign objects in the paper path, and bad paper feeding sensor).

2. Stuck in the middle part (the alignment roller is not good, the paper path sensor is not good) 3. The fuser is jammed (the separation claw is not good, the paper sensor is not good, the fuser itself is not good, and the paper output hall is not good).

Here's how to do it before stupidity:

1.Remove any remaining paper from the feeder and open the feeder cover.

2.Gently remove the jammed paper from the feeder.

3.Close the feeder lid and reload the removed paper (if any) into the feeder.

4.Open the scanner cover, grasp the mis-sent paper, and carefully pull it to the right with both hands to remove it from the feed area.

5.Close the scanner cover and reload the removed paper into the feeder.