-
Such a silt well cannot be repaired, and the well can only be replaced. Of course, professional ones can also be repaired, but this cost is not something that farmers can afford, nor is it a mine or an oil well, and the cost is completely disproportionate to drilling a new well, so it is not necessary.
-
It is caused by the wall of the well. At this time you are better off using a casing. Sometimes the extrusion of sediment can cause the wall to deform.
-
The pump has to be overhauled every few years, sometimes some small faults occur when the maintenance is not in place, the pump can not pump water, the rural physique is better and the old man begins to pull the pump, but the pump is stuck in the rock layer, and it can't be dragged! The pump is connected to the wire, and the rope that pulls the pump is also a stainless steel wire rope, and we can't pull it out of any strength, and the pump is very heavy and weighs almost 100 pounds.
-
Abstract If there is no other possibility, it is the deep well pump that is stuck now, and the outlet of the deep well pump is generally linked by steel pipe sections.
If so, a section of the pipe connecting flange down the ground is fixed and pulled by a rope or steel wire (no need to go down, the rope naturally goes down through the flange, and then pulls upwards around two circles), pads a wooden board (or wooden stick) of appropriate thickness above the flange of the exposed wellhead, and uses a hammer to strike down appropriately to feel the pump loose.
You can also try to pull it with a rope first and then rotate the outlet pipe to see if there are any signs of loosening.
If you don't pull up too hard, you should be able to take it out according to the method above. (There is generally a certain spatial distance between the pump and the deep well, unless the deep well is deformed.) If the deformation is slight, the problem is easy to solve.
If the deformation is too large, it is more troublesome. If the above method does not work, it depends on the situation on site.
What should I do if the water pump is stuck in a deep well at a distance of about 60 meters from the ground, and I can't go down and can't pull it up? The depth of the well is 130 meters. Seeking a master...
If there is no other possibility, it is the deep well pump that is stuck now, and the outlet of the deep well pump is generally connected by steel pipe sections. If so, a section of the pipe connecting flange down the ground is fixed and pulled by a rope or steel wire (no need to go down, the rope naturally goes down through the flange, and then pulls upwards around two circles), pads a wooden board (or wooden stick) of appropriate thickness above the flange of the exposed wellhead, and uses a hammer to strike down appropriately to feel the pump loose. You can also try to pull it with a rope first and then rotate the outlet pipe to see if there are any signs of loosening.
If you don't pull up too hard, you should be able to take it out according to the method above. (There is generally a certain spatial distance between the pump and the deep well, unless the deep well is deformed.) If the deformation is slight, the problem is easy to solve.
If the deformation is too large, it is more troublesome. If the above method does not work, it depends on the situation on site.
There are also 40 meters of three-star wire that fell into the well, pp pipe, connected.
Wait a minute, kiss, you can use the same method.
Now the PP pipe is also broken 42 meters in it, and the pipe can't be lassoed with a wire rope, can you use a well fishing machine to grab the wire.
Can you use a well drill to catch the wires?
Kiss, the wires are a little bit now.
It is not recommended that you use it here.
There is a possibility of damage.
Five meters down from the wellhead, the line was broken, and it all fell into the well, and we broke the pipe by 42 meters.
Now you can't tie the water pipes.
I'm sorry, dear.
-
The roots of the tree in the well stuck the pump, and it was seven or eight meters away from the wellhead, but it couldn't be lifted, what should I do?
Hello dear, <>
The roots of the tree in the well stuck the pump, seven or eight meters away from the wellhead is not able to lift up, how to use a diameter of more than 20 mm of steel bar about 2 meters long, the top of the dislocation welding a few barbs, send a head with a thick nylon rope to tie up, continue to go down, after the hook, the rope is tied to the chain hoist, dragged on. If there is a lot of silt in the well, you can take the well to wash (blow sand) before pumping. Of course, if the pump is relatively large, increase the diameter of the steel bar and nylon rope appropriately.
There are two reasons why the deep well pump is stuck: first, it is the stone face and the slag of the well wall when digging the well, after a year of precipitation, the pump is buried, and it may be buried in the filter screen part, and the water is not available. Second, the falling object of the well wall is stuck, you pull it, see if the pump does not move, it must be the sediment buried in the pump, so you have to use something to pull up, pull it well, the falling object is stuck, the water pump can move, you pull the pump back and forth to pull up and put it back, and break the falling line envy to break the object, which is generally a vulgar stone stubble, not a stone, the stone is not broken, and generally does not fall down, so that you can pull the pump up.
In addition, the newly installed deep well pump should be moved in 1-2 months to prevent the sediment from burying the pump.
-
Hello dear, I'm glad to answer the rotten cherry blossoms for you! The solution to the 40-meter deep well water pump that can not be lifted up at 30 meters is: 1. With the help of mechanical equipment
Cranes, winches and other machinery can be used to lift the pump. It should be noted that when using mechanical backlaughing equipment, it is necessary to ensure the safety of operation and avoid damage to the pump and wellhead. 2. Disassemble the water pump
If the pump is small, consider disassembling the pump, dividing it into several parts, and then lifting it up. It should be noted that when disassembling and assembling the pump, it is necessary to ensure the operation specification to avoid damage to the pump and pipeline. 3. Adjust the position of the wellhead
If the wellhead position is relatively low, you can consider adjusting the wellhead position below the pump height, so that the pump can be directly raised. It should be noted that when adjusting the position of the wellhead, it is necessary to ensure the operation specification to avoid damage to the wellhead and the surrounding environment. 4. The pump is filled with water
If the pump cannot be lifted directly when it is placed at a distance of 30 meters, you can consider filling the inside of the pump with water, which can reduce the weight of the pump and make it easier to lift up. It should be noted that when the pump is filled with water, it is necessary to ensure the safety of the operation and avoid damage or leakage inside the pump.
-
The 80-meter deep well pump was broken, and it was a hassle to bring the pump up for repair. There is no simple, easy way to do it. General approach: tolerance.
1. With a crane crane, the deep well pump room is generally left with a skylight, the hook can be lowered from the skylight, and a special tool is used to card it when pulling out a section to prevent the pump and the pump outlet pipe from falling off as a whole, and remove a section. Continue to hang the next section until the pump is lifted to the ground.
2. When there is no crane, you can support a tripod at the skylight, and replace the crane with a chain hoist, which is also lifted up section by section.
3. The method of dragging and pulling by people is also possible, the stability is slightly poor, and the safety and reliability are not as good as those of cranes and chain blocks. Labor intensity is also higher.
-
Hello, the above questions will be answered by me. If the deep well water pump is stuck by bricks, you can try the following methods:1
Cut off the power supply: First of all, the power supply of the deep well water pump should be cut off to prevent motor damage or electric shock. 2.
Disassembling the water pump: Next, you need to disassemble the deep well water pump to find the stuck bricks. If the brick gets stuck in the suction inlet of the pump, you can try to remove it using a tool such as pliers.
If the brick is stuck inside the Buyu pump, it is necessary to disassemble the pump and clean up the part of the brick that is stuck. 3.Clean Water Pump:
Before cleaning the stuck bricks, the water in the pump needs to be drained to avoid water residue in the pump and cause damage. When cleaning, you can use detergent and a soft brush to gently scrub the inside of the water pump. 4.
Assembling the pump: After cleaning, the pump needs to be assembled back in place and the power supply connected. Start the pump and observe if the pump is working properly.
It should be noted that deep well pumps are more complex equipment, and if you do not have the relevant experience and skills, it is recommended to have a professional repair and cleaning. It is important to maintain safety and caution during repairs and cleaning. Hope it helps!
1. Add activated carbon.
Activated carbon has a good adsorption capacity and can remove odors. Pouring activated carbon into the well can remove the odor in the well and restore the clear water source. There is wrapping paper on the outside of the activated carbon, and the wrapping paper should be torn off and only powdered charcoal should be poured in. >>>More
It is most suitable to decorate in a modern minimalist style.
The pump power required for a one-meter fish tank is usually between 20W and 55W, depending on the total amount of water in the tank, the type of fish raised and the filtration. >>>More
See if the impeller is blocked, or maybe the pipe.
How much sand is needed for the decoration of an 80-square-meter house, depending on your decoration needs, calculated by ground tiles, 80 square meters need to paste about 50 square meters of floor tiles. >>>More