What should I do if the Oaks heater does not heat up, and I don t find any burned wires?

What should I do if the Oaks heater is not heating? I didn't find any burned wires, I think if the heater doesn't heat, it must be his compressor is broken, you can check the compressor to see.

What should I do if the Oaks air cooler does not heat? Not found, no new circuit found, this could be its refrigerator, it could be its compressor problem, you can look at its voltage or the compressor problem.

Hello: 1, no heating [there must be a fault], it should be checked to be confirmed.

2. The fault points are roughly: fuse breakage, heating tube damage, control circuit failure, etc.

What should I do if the Oaks heater is not heating? I didn't find that there was a broken line, if the fan was not hot, then the outside temperature was too low, so this was a fan, he didn't adapt to it, he was adapted to the tune of the south, not to the air conditioning of the north.

Hello friend. What you said about your Oaks heating machine is not heating, is the gas inside broken, you don't see it!

I've seen this happen on a light bulb once, and when the light bulb shakes slightly, the gas is all connected, and when it moves again, it falls again.

So personally, I think it should be the same. The only difference is that the heater is a bit larger than the light bulb.

Oaks heater instructions for use. First of all, the power is generated before use, and after the power is turned on, press the on/off button, select the appropriate working mode and temperature, and then you can use it.

I think if the heater doesn't heat, it must be his compressor that is broken.

Hello dear, I am glad to answer for you, the reasons and solutions for the Oaks electric heater not heating are: 1 First determine whether the electric heater indicator light is on, and then check whether the power socket is powered normally, if the plug is loose, plug it in. 2. Continue to check whether the heating wire of the heating tube is broken, whether the wiring of the heating pipe is loose or the contact is poor, this needs to be checked patiently, don't worry.

3. If the power supply is not connected to the circuit, first disassemble the face cover of the electric heater and turn on the power supply, which can generally operate normally. If the power cord is faulty, first open the rubber cover of the power cord socket and check the power cord, which is caused by the user's frequent pulling. 4. Reconnect the L lead to make it work normally.

If the cord breaks not at the socket but at the plug, a new cord will need to be replaced. 5. If there is no problem with the above, you can check other components, and switch components such as temperature control switches should also be checked in place. If an abnormality is found, replace it according to the actual situation.

Hello, what is the reason why the Oaks electric heater does not heat: 1. The wires at home are too thin 2. There is a problem with the overheating protection in the heating brigade, if it is not the line heating of the electric heater, then there is only one situation, that is, the wires are thin, which leads to overheating protection. Workaround:

1. The simple solution is to judge whether the power switch is broken or overheated to protect the shutdown and the power trip, because these are common faults and are easy to repair by yourself. If the internal heating element is broken, you can't get it yourself, so you have to send it for repair. 2. Residents should replace the new heating before the service life reaches the upper limit according to the actual situation of their homes.

3. There is a blind air release valve behind each group of radiators, which unscrews the rotating shaft to drain the air until the water flow is stable. If the screw of the air drain valve has rusted to death, you must not twist it rashly, so as not to break the air valve and cause the heating hot water to spray out, and ask professional plumbing personnel to come to repair.

1. When the air conditioner is heated in winter, because there is a heating link after starting, the external unit will work first after starting, and when the temperature of the internal machine pipeline has just begun to rise, the internal unit of the air conditioner will just start to exhaust, which is due to the effect of the air conditioner to prevent cold wind.

2. There will be a period of time after starting, the outdoor unit of the air conditioner must be defrosted immediately, this link of the air conditioner is not easy to work, defrosting usually takes 10 minutes up and down, and the hot air will be blown out again after the end of defrosting.

3. If it is an air-conditioning problem, it means that the relevant components of air-conditioning heating cannot carry out all the normal work, and there are problems of destruction and common failures.

(1) ** The air conditioner basically has an anti-cold air function for humanized considerations, if the air outlet temperature does not meet the requirements, the indoor fan is not allowed to run or run at a slight speed;

2) The air conditioner operation mode is set incorrectly and is not in the heating state; When the mode of the indoor unit conflicts, some indoor units are set to heating, and some are set to refrigeration mode;

3) The set temperature of the air conditioner is too low.

In this case, if it is not open to the human wind, this is because your task is to heat the air when there is no hot air generated, there is also a process, which makes it a normal phenomenon that the hot air is not produced, if it is used for a long time, there is still no hot air, then it is your heating pipe or line, there is a problem and needs to be repaired.

That means that the heating function of the air conditioner is broken, and you can find the after-sales department to repair it.

Dear, hello, glad for your problem, the blades of the Oaks heater do not open 1, check whether the function settings of the remote control are wrong and correct them. 2. Check whether the indoor unit fan is running during heating operation, and it is a temporary phenomenon that there is no air blowing at the beginning of heating. If the wind does not blow for a long time, it is the fault of the internal fan; If it is cold air, check whether the outdoor unit is working, if it is running, it is suspected that fluorine leakage or four-way valve failure causes no heating.

3. The failure of the external machine is due to its own fault or the failure of the components of the control circuit. It is recommended to find an after-sales service to troubleshoot electrical faults or leaks and add fluoride. I hope my answer is helpful to you, and finally I wish you good health and a happy mood again!