How to lay floor tiles on top of electric floor heating, can you lay floor heating on the original f

Updated on home 2024-07-12
7 answers
  1. Anonymous users2024-02-12

    Electric floor heating basically has no requirements for the ground, the first consideration can be the floor tiles, the thermal conductivity of the floor tiles is the best, in fact, you can consider laying solid wood flooring, laminate flooring, or multi-layer solid wood flooring, but you must not lay pure solid wood flooring, floor heating has higher requirements for pure solid wood flooring, only individual brands can be used.

  2. Anonymous users2024-02-11

    1. First of all, let's look at the key index, that is, the heat transfer coefficient of the material.

    The heat transfer coefficient of floor tiles is that of wood boards, and the thermal conductivity of floor tiles is significantly better than that of flooring.

    2. The best heat transfer material for floor heating is floor tiles, because the heat transfer coefficient of stone is large and cools quickly, as long as the floor heating cable is controlled at 3-5cm to the finished surface.

    3. The only disadvantage of floor tiles is that the comfort of the feet is not as good as that of the floor.

    4. Ordinary solid wood should not be paved with floor heating, not only the thermal resistance of ordinary solid wood.

    It is too high, and it is easy to crack due to the change of moisture content caused by floor heating, so the parquet and laminate flooring are considered at most for comfort.

    5. The practice of floor heating: first lay the heat insulation board (benzene board, then fix the floor heating pipe, then install the water separator, and then press the acceptance, backfill after qualifying, and then directly pave the floor tiles on the dry paving, that is, use dry hard cement to lay the bottom + plain cement paste.

  3. Anonymous users2024-02-10

    Dear, hello, I am glad to answer for you: is it okay to lay floor heating on the original floor tiles? A: Hello kiss<>

    Underfloor heating can be added directly. The premise is that your house is high enough. Underfloor heating in the home.

    If your building is more than a meter high, you can directly put geothermal heating pipes on top if you don't want to remove the previous floor tiles. Because the thickness of the geothermal pipe is 5cm, the minimum thickness of the cement and the lower insulation board is also 5cm, and if the house is low, you need to soak the floor tiles. The rack is high enough to be paved directly.

  4. Anonymous users2024-02-09

    The home is underfloor heating, and I want to lay a floor on top of the floor tiles, is it okay?

    Kiss! Hello, happy to answer your <>

    Pro, yes. When decorating, it is possible to keep the floor tiles, use the old floor tiles to pad the bottom, and lay wooden floors on top is not impossible, but because of the use of floor heating, the heat dissipation of floor heating needs to be considered. First of all, it is necessary to clean up the dust on the floor tiles, and the bottom of the floor tiles can be used to ensure the smoothness of the indoor ground, and it is relatively easy to lay the wooden floor on it, eliminating the need to remove the old floor tiles, speeding up the decoration progress, and saving the cost of decoration at the same time.

    It is necessary to check whether the floor tiles are loose, if there is a loose need to fix it, and measure whether the floor tiles are paved at the level, if it is uneven, it needs to be corrected, otherwise it will affect the laying quality of the wooden floor. There is a drop in the height of the space between the space with the additional floor and the space without the floor, and the joint should be treated well so as not to affect the appearance. Hope mine can help you <>

    Do you have any other questions?

  5. Anonymous users2024-02-08

    Summary. Hello, the floor tiles on the floor heating need to pay attention to the following points:1

    Make sure the underfloor heating system is fully installed and has passed the test. If the underfloor heating system has not been installed, then it is necessary to wait for the underfloor heating system to be fully installed and pass the test before tiling. 2.

    Lay a moisture barrier layer on top of the floor heating to prevent the floor tiles from getting wet. The vapor barrier can be made of PVC or PE material, which needs to be completely covered with the underfloor heating system. 3.

    A layer of cement mortar is laid on top of the vapor barrier so that the floor tiles can stick firmly to the ground. The thickness of the cement mortar should be between 3-5 mm. 4.

    Before the cement mortar is dry, lay the floor tiles on it. When laying floor tiles, it is necessary to pay attention to the clearance between the floor tiles should be consistent, and it is necessary to use tile adhesive to glue the floor tiles to the cement mortar. 5.

    After laying the floor tiles, you need to wait at least 24 hours for the tile adhesive to dry thoroughly. Then the caulking process is carried out. <>

    <> how to stick floor tiles on top of the floor heating.

    Hello, the floor tiles on the floor heating need to pay attention to the following points:1Make sure the underfloor heating system is fully installed and tested.

    If the underfloor heating system has not been installed, then it is necessary to wait for the underfloor heating system to be fully installed and pass the test before tiling. 2.Lay a moisture barrier layer on top of the floor heating to prevent the floor tiles from getting wet.

    The vapor barrier can be made of PVC or PE material, which needs to be completely covered with the underfloor heating system. 3.A layer of cement mortar is laid on top of the moisture barrier so that the floor tiles can be firmly adhered to the ground.

    The thickness of the cement mortar should be between 3-5 mm. 4.Before the cement mortar is dry, lay the floor tiles on it.

    When laying floor tiles, it is necessary to pay attention to the clearance between the floor tiles should be consistent, and it is necessary to use tile adhesive to glue the floor tiles to the cement mortar. 5.After laying the floor tiles, you need to wait at least 24 hours for the tile adhesive to dry thoroughly.

    Then the caulking process is carried out. <>

    <> dear, the installation of floor heating system requires professional skills and experience, if you do not want to be familiar with the installation of floor heating system, it is recommended that you ask a professional floor heating installation company to install. In addition, when laying floor tiles, you need to pay attention to the choice of floor tiles, and it is best to choose tiles that are suitable for the difference of Yeqing sleepy floor heating system, so as to avoid problems such as cracking. <>

    <>Can you use pure cement on the floor tiles to stick to the floor heating, the sand and ash layer is about 4 cm.

    Hello, when installing floor tiles on underfloor heating, you need to use special underfloor heating mortar from Qiaohui, instead of pure cement. Floor heating mortar has good thermal conductivity and high temperature resistance, which can ensure the close fit between floor tiles and floor heating, so as to improve the efficiency and comfort of floor heating. If pure cement is used, it may cause a gap between the floor tiles and the floor heating, which will affect the heat transfer effect of the floor heating.

    In addition, the thickness of the sand-ash layer also needs to be adjusted according to the requirements of underfloor heating, which is generally recommended to be between 3-5 cm. It is recommended to consult a professional floor heating installation company or construction team to ensure the installation quality and effect. <>

  6. Anonymous users2024-02-07

    My house has been tiled, how to lay electric underfloor heating on the floor tiles?

    Yes, but there will be many drawbacks, because it is necessary to lay a layer of insulation board pipes coiled on the insulation board, then a layer of sand and ash cushion, and then the bricks also need to be covered with ash, and the indoor height is increased by about ten centimeters to reduce the entire height of the house. And the original furniture doors need to be transformed to improve the height, and the entrance ground is significantly higher than the outdoors. In addition, the renovation of floor heating involves the laying of floor heating pipes, and there is a certain thickness, so the space height must be considered for the transformation of floor heating.

    Of course, if the height of the house itself is not low, it will have little impact and can be directly transformed.

  7. Anonymous users2024-02-06

    Summary. 1. First of all, prepare the required materials, including floor tiles, tile adhesive, tile corners, tile cutters, plasterers, plastering materials, plastering tools, etc. 2. Check the surface of the floor heating to ensure that it is smooth, no damage, no pollution, no stagnant water, no hollowing and other phenomena.

    3. Arrange the floor tiles according to the design drawings, determine the position of the bricks, and place the corner lines of the bricks on the edge of the bricks in order to complete the installation of the bricks. 4. Apply the tile adhesive evenly on the floor heating, then place the floor tiles according to the position of the design drawings, and fill the gaps between the bricks with a plasterer. 5. Evenly apply the plastering material to the floor tiles, and use a plastering tool to smooth the plastering material to make the surface of the floor tiles smooth.

    6. Finally, use a tile cutter to cut the corners of the bricks to make the edge of the floor tiles perfect and complete the paving of the floor tiles.

    1. First of all, prepare the required materials, including floor tiles, ceramic tile glue, tile corner lines, tile cutters, plasterers, plastering materials, plastering tools, etc. 2. Check the surface of the floor heating to ensure that Sun Xi is smooth, no damage, no pollution, no stagnant water, no hollowing and other phenomena. 3. Arrange the floor tiles according to the design drawings, determine the position of the bricks, and place the corner lines of the bricks on the edge of the bricks in order to complete the installation of the bricks.

    4. Apply the tile adhesive evenly on the floor heating, then place the floor tiles according to the position of the design drawings, and fill the gaps between the bricks with a plasterer. 5. Evenly apply the plastering material to the floor tiles, and use a plastering tool to smooth the plastering material to make the surface of the floor tiles smooth. 6. Finally, use a tile cutter to cut the corners of the bricks to make the edge of the floor tiles perfect and complete the paving of the floor tiles.

    Fellow, I really didn't understand, I can be more specific.

    1.Reason: The floor heating is paved with bricks, which will reduce the efficiency of the floor heating system, because the floor tiles will reflect the heat back, which will affect the effect of floor heating.

    2.Solution: Before laying the floor tiles, the temperature of the floor heating system should be lowered to avoid overheating the floor tiles and affecting the effect of floor heating.

    In addition, when laying floor tiles, heat protection pads should be used to prevent the floor tiles from being overheated. 3.Personal Tips:

    The temperature of the floor heating system is generally between 20-30 degrees, if the temperature is too high, it will affect the effect of floor heating, so attention should be paid to controlling the temperature.

Related questions
13 answers2024-07-12

Methods of laying underfloor heating.

1. Installation method of dry floor heating. >>>More

9 answers2024-07-12

Try not to spread a large area of carpet for floor heating, for the following reasons: >>>More

4 answers2024-07-12

As the world's most cutting-edge technology in the field of carbon fiber, Japan has a leading advantage in the development and production of carbon fiber technology, and the United States cannot compete with Japan in many aspects. Relying on the strong technical support of Shell Local Heating Japan Technology Center, Shell Local Heating focuses on the R&D and production of carbon fiber floor heating. In line with the concept of "paying attention to cutting-edge technology and arming products with science and technology", Shell Local Heating closely follows the world's most cutting-edge carbon fiber technology and draws on the new technology used in the field of global carbon fiber floor heating. >>>More

11 answers2024-07-12

The whole process of electric floor heating system is based on electricity as energy, does not produce any harmful substances to the human body, and is recognized as a healthy and comfortable heating all over the world. As early as more than 30 years ago, Western countries fully used electric heating with heating cables as the heating element, and only Russia and China are still using traditional boiler heating in the world today. Coal heating is not only a waste of resources and not environmentally friendly, but also produces a lot of harmful gases, and electricity is a renewable energy source, which can be obtained by using hydropower, wind power, nuclear power and other means. >>>More

14 answers2024-07-12

Floor heating thermostat has a week programming function, when the new product is first used, if you need to use a week of programming control, then you have to set the time parameters and temperature values of each period, generally a week of programming is divided into two cycles, respectively, "12345", "67" 5 + 2 programming mode, each day is divided into 6 periods, after setting a week of programming parameters, the thermostat will be controlled according to the parameters you set, if you do not need to use programming mode control, All you need to do is set the thermostat programming mode to manual mode (how to do it: press the mode button to change the working mode). >>>More