How to lay floor heating, how to lay floor heating?

Methods of laying underfloor heating.

1. Installation method of dry floor heating.

In order to solve the problems of difficult construction, long construction period and difficult maintenance after installation of the traditional wet floor heating installation method, the dry installation method came into being. Dry installation no longer uses a concrete bean stone layer to fix the plumbing pipes, but uses a special dry floor heating module or plastic formwork, which is very convenient to lay the pipes stuck in the pipe groove of the formwork. The floor is laid directly on the surface of the dry module or formwork, and the hot water heat is evenly transferred to the floor through the thermal conductivity layer of the module aluminum plate or the plastering layer of the formwork, so as to achieve fast floor heating.

2. Installation method of wet floor heating.

The installation process, which is also relatively low, is the leading process in the domestic floor heating market. The so-called wet type refers to the use of concrete to bury the floor heating pipes, and then lay ground, tiles and other ground materials on top of the concrete layer. This layer of concrete not only protects and secures the plumbing pipes, but also serves as the main channel for heat transfer.

The concrete layer evenly distributes the heat and reduces the occurrence of localized overheating or overcooling.

1. Draw the indoor floor plan first, according to your own ideas, lay the position of the floor heating to draw the floor heating design drawing, if you use a wall-hung boiler, each circuit is controlled at 70-80 meters, and the total length of each circuit is relatively close, specify the installation position of the water separator (wall-hung boiler).

2. Go to the building materials city to buy water separators (according to the number of circuits you design), insulation boards (extruded plastic boards, benzene boards), reflective films, steel mesh, pipes (according to the total number of meters you design), 1 package of cable ties, 1 roll of wide tape, more than 2 valves, 1 pressure gauge, more than 4 expansion screws, and other accessories are purchased according to actual needs.

3. Clean the ground, leveling, bathroom, kitchen and do 1 waterproofing.

4. Lay insulation boards and reflective films, pave expansion joints in the corners of the walls, and lay steel meshes (the joints of the reflective film should be glued with tape, and the steel mesh joints should be tied up with cable ties).

Ask the installer directly, and he will take care of the ground for you.

Do it according to the dimensions on the drawing.

Mainly install the underfloor heating pipes to, in a hidden and safe place.

Process: 1. In the case of flat ground, first cover all the ground that needs to be paved with a benzene board of about 5mm below.

2. Cover the benzene board with a layer of heat insulation film.

3. Lay geothermal pipes on the heat insulation film. It should be noted here that about 5m of geothermal pipes should be laid per square meter and there should be no joints. The spacing between the tubes should be 20cm.

4. After the geothermal pipe is laid, fill it with an hourglass (that is, the thing saved by sieving sand).

5. Finally, level it with cement mortar of about 1:5 on top. (Do not calender, otherwise it will affect the heat dissipation effect.) I won't say much about the bricks)

Note: 1. The choice of a geothermal company. As the old saying goes, don't save on hidden projects, you must choose a geothermal company with qualifications, strength, good reputation, strong professionalism and rich construction experience, and sign a formal contract. This is a decisive condition for ensuring the quality of the project.

2. Selection of geothermal pipes. Don't be confused by the low **, the quality of geothermal pipes directly affects the service life of geothermal engineering, choose the best underground pipes, above-ground components (including water separators, valves, filters, etc.). Taking a step back, even if there is a quality problem in the future, the pipe manufacturer will have some compensation.

3. The best selection of above-ground parts is all copper parts of qualified quality. Each underground part of the geothermal project must be a complete whole pipe, and no connection of any kind can be taken.

In fact, it doesn't matter what kind of pipe is filled with cement mortar (but you can't use too garbage).

In fact, when laying geothermal heat, the most feared is air resistance (air resistance: to put it bluntly, there is air in the tube).

Therefore, when laying geothermal heat, especially before backfilling, be sure to let the workers check it carefully.

The laying of underfloor heating requires the following steps:1Determine how the underfloor heating will be arranged:

Floor heating can be used in two ways: water heating and electric heating, water heating needs to lay pipes under the ground, and electric heating needs to lay heating cables or heating films. 2.Prepare the ground:

The ground needs to be flat, dry, dust-free, oil-free, etc., so as to facilitate the laying of floor heating. 3.Laying insulation:

Lay a layer of insulation materials on the ground, such as polystyrene foam board, extruded plastic board, etc., to reduce heat loss. 4.Laying underfloor heating pipes or electric banquet cables:

According to the design drawings, lay the floor heating pipes or cables on the insulation layer, paying attention to the spacing and arrangement between the pipes or cables. 5.Testing the underfloor heating system:

After laying the underfloor heating pipes or cables, tests are required to ensure that the underfloor heating system is functioning properly. 6.Laying of floor materials:

Laying floor materials such as floor tiles, floors, etc., on underfloor heating pipes or cables. 7.Installing the Thermostat:

Depending on the type of underfloor heating system, a thermostat is installed to control the temperature of the underfloor heating. 8.Commissioning of the underfloor heating system:

After the thermostat is installed, it needs to be commissioned to ensure that the underfloor heating system is functioning properly. The above are the steps of laying underfloor heating, it should be noted that design and planning need to be carried out before laying underfloor heating to ensure the effectiveness and safety of underfloor heating system.

Underfloor heating is a system that heats the floor through pipes or electricity** to heat the floor. Here are the five key steps and summaries for underfloor heating laying:

1.Planning and design: Before you start laying underfloor heating, you first need to plan and design your system. This includes identifying the heating area, choosing the right heating equipment and plumbing arrangement. Ensure planning and design are in line with local building codes and requirements.

2.Preparation: Before laying underfloor heating, some preparation work is required.

First, clean the slabs to ensure that the surface is flat, dry and clean. Repair any damage or defects to the floor surface if needed. Then, an insulating layer is installed to prevent heat from escaping downward.

3.Installation of plumbing or electricity**: According to the design plan, install heating pipes or electricity** on the floor.

Heating pipes can be prefabricated plastic pipes or metal pipes. The plumbing arrangement can be spiral, serpentine, or grid-shaped, depending on the design and heating needs.

4.Connecting the water and electricity supply systems: Once you have completed the installation of underfloor heating pipes or electricity**, connect them to the water supply system (if it is hot water heating) or the power supply system (if it is electric heating). Make sure the connection is tight, there are no leaks, and it is tested according to the specification requirements.

5.Completion of floor laying: After the installation of the underfloor heating system is completed, the floor can be continued. This can be floor tiles, wooden floors, carpets, or other flooring materials. Depending on the need, you can choose to install a thermal conductive layer or a chain silver chain thermal layer to improve the heating effect.

Summary: Floor heating installation requires planning and design, preparation, installation of plumbing or electricity**, connection to water and electricity supply systems, and completion of floor laying. These five steps ensure the proper installation and proper functioning of the underfloor heating system.

Throughout the process, building codes and requirements should be followed, and all connection and installation work should be ensured to meet safety standards.

Underfloor heating is a type of heating that is laid under the floor. Its laying method mainly includes the following steps:

1.Design: First of all, it is necessary to design the floor heating system, including the required heat dissipation area, heating mode, pipe direction and pipe length, etc.

2.Cleaning: The floor should be cleaned to remove dust, grease and moisture to ensure that the floor is level.

3.Laying insulation: Laying insulation to reduce energy loss. Generally, polystyrene, extruded plastic board and other materials are selected.

4.Laying a reflective film: Laying a reflective film to reflect the geothermal heat and reduce heat loss downward.

5.Installation of pipes: Installation of floor heating pipes, generally using PEX pipes or PE pipes, pipe spacing, pipe direction, pipe length and other factors should be paid attention to when laying pipes.

6.Test: Conduct a test after the installation of the pipes to confirm that there is no leakage in the floor heating pipes.

7.Covering the floor material is quietly changed: covering the ground material, generally the floor, floor tiles, etc. can be selected.

There are many factors that need to be considered when laying underfloor heating, including system design, pipeline layout, insulation materials, etc., and generally require professionals to install them.

The laying of underfloor heating needs to follow the following steps:

Clean the floor: Clean the floor of the paving area to ensure that it is smooth and free of debris.

Number of yards of separator film: Lay a layer of separator film on the ground after cleaning to isolate moisture and other pollutants on the ground.

Installation of heat dissipation pipes: According to the design drawings, install heat dissipation pipes according to the specified spacing, depth and slope requirements. Attention is also needed to ensure the heat dissipation and service life of the pipes.

Connect the pipe and control system: connect the heat dissipation pipe and the water pump, and install the floor heating control system.

Test run: After all the laying is completed, the test run is carried out to check whether there is any water leakage, water seepage or failure. If there is a problem, it needs to be fixed in time.

In the cold north, if there is no heating, it is easy to freeze hands and feet, so many people will install underfloor heating at home to keep warm. The method of laying underfloor heating is as follows:

1. Before the floor heating officially starts to be laid, the indoor ground should be cleaned to ensure the smoothness of the ground and eliminate the unevenness and debris on the ground. Then, the entire home needs to be inspected on the spot to determine where the wall-hung boiler and manifold will be installed.

2. The main water pipe of floor heating must use hot water pipe, PP-R or aluminum-plastic pipe can be used, and the pipe must be strictly installed in the design drawing, and the installation is straight and neat.

3. Make a groove in the place where the water collector is installed, bury the temperature control line, and put the relevant temperature control line around it for connection.

4. Lay the insulation layer on the whole ground, and when laying the insulation layer, be sure to cut the insulation board according to the actual size to ensure that the insulation board is cut neatly, and then lay.

5. Paste it on the laid insulation board layer, be sure to keep the reflective film flat and tight, and there can be no wrinkles and misalignment, and the reflective film must be pasted with tape.

Introduction to underfloor heating:

Floor heating is the abbreviation of floor radiant heating, which uses the whole ground as a radiator, through the heat medium in the floor radiation layer, evenly heats the entire ground, and heats the room through the ground in the way of radiation and convection heat transfer, so as to achieve the purpose of comfortable heating.

According to different heat transfer media, it is divided into two categories: water floor heating and electric floor heating, and according to different pavement structures, it is mainly divided into dry floor heating and wet floor heating. Plumbing refers to a heating method that heats water to a certain temperature and transports it to the water pipe cooling network under the floor, and realizes the purpose of heating by heating the floor.

1.Laying the ground is uniform.

The laying of the underfloor heating system needs to keep the floor uniform, and there can be no floors of different heights and materials in the same room. If the floor needs to be replaced, it should be replaced after the installation of the underfloor heating system has been completed.

2.Good insulation.

Underfloor heating systems need to be well insulated to prevent heat loss and reduce heating time. The insulation should be evenly and securely covered on the ground without any leaks.

3.The layout is reasonable.

The layout of the floor heating system needs to take into account the actual use of living space, and reasonably design the heating area and heat dissipation area according to the temperature requirements of different areas, the layout of home rock fiber and other factors.

4.The control system should be reasonable.

The underfloor heating control system needs to be set up properly to maintain the temperature stability of the room. You should choose a system that automatically adjusts the temperature and saves energy, so that it automatically stops heating when the set temperature is reached.

5.Safety first.

When installing a floor heating system, it is necessary to strictly adhere to the relevant regulations and standards to ensure that the system is safe and reliable. At the same time, it is necessary to pay attention to fire prevention measures and keep the system and the surrounding environment dry and clean to avoid unnecessary accidents.

1. Judge the forest to dig acres to see the area. In the north, the weather is cold, and the number of roads is naturally more. Concise.

Second, look at the effect. The more the number of roads, the better the effect.

Third, the project is generally 20 square roads, too close is not necessary.