The mobile phone fell into a puddle, how to remove the cover and remedy it?

The mobile phone fell into a puddle, how to remove the cover and remedy it? If you buy a mobile phone this year**3000 yuan or more, then I don't recommend you to do it yourself, and send it to a mobile phone repair shop to deal with. For old phones and cheaper phones, you can try to disassemble the back cover by yourself, then remove the motherboard to absorb the moisture and dry it with a blow dryer, and blot the moisture of the components inside with a cotton cloth and dry it with a hair dryer.

If there is water in the screen, remove it as much as possible, absorb the water, and then blow it on the hair dryer. Then turn it on to test whether it can be used normally.

If you are using a Huawei phone, it is recommended that you turn off your mobile phone and bring the relevant proof of purchase to a nearby Huawei customer service center for maintenance. You can check the address of a nearby Huawei Customer Service Center on the Huawei website.

Precautions after water and liquid ingress in the mobile phone:

1.Do not move or shake your phone frequently after water is ingress to avoid moisture spreading inside the phone.

2.Do not use a hair dryer or bake at high temperatures (including microwave heating) after water is in, to avoid liquid being blown into the phone and the heat damaging the phone.

3.Mobile phones are made of delicate electronic components, and there is a potential risk after water ingress, so please keep your phone turned off.

4.If you don't have a backup of your data, there may be a risk of data loss during repairs. After you go to the Huawei Customer Service Center, you can consult with a staff member to help you evaluate whether you can back up your data.

1. Shut down in time.

When the mobile phone gets into the water, first turn it off immediately to avoid the result of burning the motherboard.

2. Remove moisture.

First of all, you can quickly wipe it with a clean towel, and then use a hair dryer to dry the inside, pay attention to the distance between the hair dryer tuyere and the mobile phone, so that the wind temperature blowing on the mobile phone is close to normal temperature, and the time for the hair dryer to blow the mobile phone should not be too long, 20 minutes is basically fine.

3. Drying treatment.

1. Wrap the mobile phone in a paper towel and throw it into the rice, which helps to absorb all the remaining water droplets and water vapor inside the mobile phone, but after all, rice is only an emergency measure, and you can usually prepare some desiccant or drying box in case of emergency.

2. At this time, you can try to turn on the mobile phone, if the water into the mobile phone is not serious, it should be able to turn on normally. If you still can't turn it on, you can only send your phone to a professional repair shop.

Step 1: Shut down immediately.

If you fall into the toilet, or sink and other places where the water is not deep, immediately salvage the phone, regardless of whether the phone automatically goes black, you must quickly press and hold the power button to turn it off. If it continues to be used with power, it will cause a short circuit in the internal components and cause the battery**; If it is a removable battery, it is best to remove the battery, SIM card, memory card and other accessories first, which is more conducive to the rapid recovery of the phone.

However, other circuit boards and parts should not be disassembled by themselves, and it is more reliable to hand over to professionals if they want to repair them.

Step 2: Blot the water with a paper towel.

At this time, do not rush to dry the phone with a hair dryer or oven, because the high temperature of the mobile phone will cause the parts to deform and destroy the internal components. Don't try to dry the water out of your phone, as it may allow water from the surface to seep into the deeper parts of the body, which will outweigh the benefits.

The safest way is to wrap the phone in a paper towel, quickly absorb the water on the surface, and then use a fine cotton swab to clean the earphone hole, charging wiring hole and other parts to avoid external moisture seepage.

Step 3: Save the phone from the water.

The most scientific method is to disassemble the machine to absorb water and air dry, but considering that many people do not know how to disassemble the machine, here is a practical method, that is: desiccant, rice water absorption method. The ideal is actually desiccant, but many people don't have it at home, so rice has become a common choice.

Seal the dried rice and the phone together, and let it sit for a few days, and the phone will probably come back to life. Be sure to use dried rice here!

The phone fell into the pit, how to clean it? If there is water, it will be more troublesome at this time. If there is no water ingress, it is still easier to clean. Professional repair shops can. Clean.

1. See if it is completely immersed in the yellow soup in the toilet, if not, quickly pick it up, don't mind picking it up directly with your hands, if you feel dirty, wrap your hands in a plastic bag or paper towel to pick it up.

2. If it is completely immersed in the yellow soup, then put on a disposable glove or plastic bag and hands, and then go to scoop it up. Regardless of whether the toilet is squatting or sitting, the principle is pretty much the same.

3. After the mobile phone is picked up, whether it is submerged in the yellow soup or not, do not turn it on, because the opening will be short-circuited instantly, causing the mobile phone to be completely unrepairable.

4. You can't be in a hurry to wipe the water on the mobile phone, because the most important thing now is not to wipe the water, but to take out the battery to prevent a short circuit.

5. If the machine cannot be turned on after 24 hours, it should be taken to the professional as soon as possible, and tell the professional about his situation and the measures he has taken.

If the economic conditions are good, it is recommended to throw away and buy a new one. If you don't want to buy a new one, pick it up and wash it, and wipe it several times around the alcohol perimeter to disinfect.

What to do if the phone falls into the water.

1. Falling into clean water when the power is on, this situation generally does not need to be disassembled.

Step 1: Power off as soon as possible.

Step 2: Shake it dry vigorously, but don't shake the machine off, the idea is to shake the water out of the screen. If there are water droplets left on the screen, there will be traces after drying.

Step 3: Place under a slight heat source such as a desk lamp or spotlight to let the moisture slowly dissipate. This process takes more than six hours. Do not use a strong heat source such as a hair dryer in a hurry.

After these three steps of processing, the power supply can basically work normally.

2. Drop into non-corrosive liquid in the case of power failure. In this case, it can be assumed that the machine is not damaged. But maybe the LCD screen will be more ugly.

Step 1: Shake dry vigorously, but don't shake the machine off.

Step 2: If there is no trace on the LCD screen, process it according to the first point point 3.

Step 3: If there is something left on the screen and it is very serious, do not deal with it according to point 1 and paragraph 3, because although the electronic circuit can work normally, the screen may be quite ugly. It can be sent to the nearest maintenance department for processing or dismantling the machine for cleaning by yourself.

3. Falling into non-clean water when the power is on, or falling into corrosive liquid or viscous liquid or other clean liquids regardless of whether the power is on or not.

This is the most troublesome situation, but there is also a great chance that the machine will recover after proper treatment.

Step 1: Power off as soon as possible.

Step 2: If you have fallen into a corrosive liquid (e.g. seawater), rinse the machine with clean water immediately. Or immerse the machine in clean water and try to dilute the corrosive liquid inside.

Step 3: Disassemble the machine as soon as possible. But take your time when disassembling the machine.

Step 4: Rinse with alcohol or professional washing water.

Step 5: Assemble or pile up the disassembled items to the maintenance point, and let the maintenance point clean and assemble again.

If you use a vivo mobile phone, the liquid inlet treatment method of the mobile phone is as follows:

1. Shut down immediately and take out the SIM card and SD card; Do not force it on, it is very likely to cause a short circuit.

2. Lay the fuselage flat, use a paper towel or soft cloth to absorb water, and come in to suck out the water in the gap; Try not to move your phone when absorbing water.

3. Do not attempt to charge; Don't shake your phone too hard; Do not heat your phone.

4. Stand in a ventilated and dry place, and place it with the screen facing up and the front camera facing upward;

5. Bring your mobile phone to the vivo customer service center as soon as possible and let the maintenance engineer conduct professional testing. Customer service center address: Enter the vivo official website vivo**app--my-service outlets or vivo official website web version--bottom of the bottom--service support--service network inquiry--select the province and city to query the customer service center address.

It is recommended to contact ** in advance before going to avoid empty running, plan the itinerary reasonably, and travel safely.

If your phone falls into a puddle, it is recommended not to use the water heater to pick up the phone directly, and take it to a mobile phone repair shop for repair after the water is clean.

Scoop it out, quickly take it out, then wrap it in toilet paper and bake it next to the light bulb.

What phone? Is it waterproof.

Ask for more blessings.

Be cautious next time.

1. After the mobile phone enters the water, take out the battery as soon as possible, and never try to turn it on. Then use a screwdriver to disassemble the phone and mark it one by one for easy reassembly. After that, 2. Use a hair dryer to dry the parts one by one, and the temperature should be lower than 75. Finally, before assembly, conditionally wipe it with pure alcohol (anhydrous alcohol).

3. If you can't do it, you can only go to maintenance, sometimes the cost of maintenance, it's better to buy a new one, depending on the price of your machine, hehe...

That's pretty much it, I hope it helps!

I open a mobile phone store, your situation is very common, as long as it is not too bad luck to be burned motherboard, there is no problem, disassemble and spray on the electronic cleaning agent and then blow dry, the mobile phone store generally charges 30, if you blow dry yourself, there is no cleaning agent and it is easy to rust.

1. Don't turn it on immediately, then it will be expensive.

2. Unplug the mobile phone board.

3. Put it in a cool place and let it rest thoroughly for 2 days to dry in the shade.

4. Don't be in a hurry to try to start the machine during the process.

5. Then go to the brand after-sales store to open the shell and deal with it.

Remove the battery, dry for 1-3 days, and then install it and try it, if it doesn't work, you can only warrant it.

Dry the hair dryer and turn it on after three days, basically no problem It depends on the quality of your phone.

Don't turn it on, remove the battery, dry it in the sun or blow it on a hair dryer or bake it under an old-fashioned desk lamp, in short, use it after a little time, dear!

Take it to the maintenance office and you can't do anything about it.

It is best to disassemble and wipe the water on the circuit board dry when taking it out of the water, the customer service does not recommend that you disassemble it, but then it will tell you that it is not covered by the warranty, and it costs money.

In fact, there is no better way to do it than you do now.

Leave it to fate.

Good luck

If you are using a Huawei phone, we recommend that you do the following:

1. Please try to place your phone in a dry and ventilated place and use a paper towel to blot the water stains on the surface of your phone.

2. If the phone is turned on, press the power button to turn it off; If your phone is turned off, don't try to turn it on.

3. Please take out the SIM card and microSD card.

4. Take your phone to a Huawei customer service center as soon as possible to avoid unnecessary losses.

Precautions: 1. Do not move or shake the mobile phone frequently after entering the water, so as to avoid the spread of moisture inside the mobile phone.

2. Do not bake with a hair dryer or stove after entering the water, so as to avoid the liquid being blown into the inside of the mobile phone and damaging the mobile phone at high temperature.

3. Some mobile phones can be turned on and used normally after simple treatment, but the mobile phone is composed of precision electronic components, and there is a hidden risk after water ingress, so it is recommended not to try to turn it on.

4. During the repair process of the mobile phone, the data may be lost.

If your mobile phone is flooded with water or liquid, it is recommended that you do not try to turn it on to prevent damage to the internal components due to a short circuit inside the machine. It is recommended that you bring the machine to the local after-sales service center, and the engineer will help you test, and the specific cost is subject to the test results of the service center.

There are two ways to inquire about phone repairs**:

Way 1Log in to the official website to inquire about the reference benchmark for maintenance costs outside the warranty period and the reference for spare parts**.

Method 2: Consult the service center to understand the repair cost: send the mobile phone to the nearest service center, and the engineer will determine the specific maintenance of the machine according to the product test results**.

If the mobile phone accidentally enters water or liquid, it is recommended that you do not try to turn on the phone to prevent damage to the internal components due to a short circuit inside the machine (if the machine battery is removable, it is recommended to remove the battery). It is recommended that you bring the machine to the local Samsung after-sales service center, and the engineer will help you test, and the specific cost is subject to the test results of the service center.

[After the mobile phone is injected, it is recommended that you do not try to turn it on again, if it is turned on, please turn it off as soon as possible, you can press and hold the power button for more than 10 seconds].

Because mobile phones are electronic products. If the inside of the mobile phone is flooded, although the external water traces are wiped dry, there are impurities in the water, and the impurities will be adsorbed in the mobile phone motherboard and display components, and if they are not removed for a long time, they will be damaged by the components. If you blindly start the machine before cleaning and maintenance, it is easy to cause a short circuit in the components, causing unnecessary losses and dangers.

It is recommended to send the phone to the nearest Samsung service center for testing and repair as soon as possible.