How to burn the floor heating boiler to be warm, and how many degrees the floor heating boiler is ge

In the case of a plumbing boiler, for example, there are four ways to ensure a good temperature and save money:

First: Manually and completely turn off the water flow in areas that will never be used for 2 weeks in order to reduce unnecessary heat loss. When the plumbing is first installed, try to mark the water valve corresponding to the heating space as clearly as possible, so that it can be completely closed when not heating.

Second: When you leave the house, turn down the heat, but don't turn it off completely. Reducing the temperature difference between indoor and outdoor can reduce unnecessary energy loss.

The faster the heat loss in the home heating system, mainly depends on the temperature difference between indoor and outdoor, the larger the temperature difference, the more energy is lost through the heat conduction of the wall, and the smaller the temperature difference, the less energy is lost. But don't turn off the underfloor heating completely, as it will take longer for the boiler to heat the water from the floor coils. If the temperature is set to 12 degrees when not heating, it may take up to 2 hours for the boiler to heat the ground; If the heating is turned off, the ground temperature may be as low as 2-3 degrees, and it may take 6 hours or more for the boiler to heat up.

In order to ensure the heating effect, it is recommended to leave the room and do not turn off the plumbing.

Third: when replacing the boiler, try to choose a boiler with high energy efficiency. Because in the plumbing system, the boiler is a wearing part, because it continues to burn for several months in winter, so the life of the boiler is generally about 6 years, and the boiler can be used after 6 years, but the failure increases, and the energy efficiency, noise, power, etc. will also have different changes, at this time you can consider replacing a new boiler.

Fourth: Minimize limescale in the floor heating coils. In most areas of our country, the water hardness is relatively high, and the calcium carbonate in my water.

Ah, wait for inorganic salts.

The content is relatively high. After the water is heated by the boiler, these inorganic salts will sink down to form scale, which can clog the boiler water tank water pipe, ground coil unit, and manifold.

etc., to reduce the efficiency of hot water. There are two ways to remove scale, one is to clean the scale once a year, and the other is to fill the purified water directly with the water purifier.

From upstairs. Know.

Your boiler hasn't been boiled.

The temperature of the return water is not higher than 50 degrees.

This can tell you accurately.

Your stove.

Heat generated.

Inadequate. Not having the ability to reach the temperature you expect.

The heat generation of the stove is not enough.

There are two factors.

One is. You burned.

Factor. The second is.

factors of the production of the stove itself.

Let's talk about the burnt first.

Determine this factor.

You have to know your local area.

2 floors with 350 square meters of underfloor heating.

Every day. Coal consumption.

Have you burned enough?

There are not enough.

Heat. What kind.

How about the boiler.

Installation. None of them can reach your desired temperature.

Suppose you burn it.

of the same area.

Coal consumption. It's not hot indoors.

Here it is. Problems with the stove.

That is. I said it.

The second factor.

A boiler. How much calorific band and how large area can the boiler produce.

It is directly related to the production.

in your home. Identify the issue.

It is the amount of coal consumed in a day for the same area.

Weigh it out. Normal in one day.

Burn out. Check the room temperature.

Not up to it. Temperature.

It is. The stove is not big enough (

As for what you said.

700 stoves.

Is that. What the manufacturer says.

There must be discrepancies.

It's all big he said.

Practical insufficient. Selected stoves.

Good and bad. There are a couple of key ones.

Index. One is.

The stove should emit white smoke.

This illustrates the stove.

Burn well. The combustibles were burned sufficiently.

The second is. The slag should be white.

The combustibles were burned sufficiently.

There is nothing left. The third is.

One important point. It's a chimney.

The temperature should be low. This illustrates.

stove. High utilization of heat energy.

No heat loss.

If the boiler is often boiled, it is not well circulated, mainly because of the problem of the circulating pump, the place where there is a short circuit in the pipeline, etc.

If the boiler does not have the phenomenon of boiling the pot, and the return water temperature is lower than 50 degrees, it means that the boiler is small.

The temperature of the automatic circulating pump is about 80 degrees.

Summary. Kiss! Floor heating boilers are generally turned on to 40 degrees.

Kiss! Floor heating boilers are generally turned on to 40 degrees.

Kiss! The temperature of the floor heating boiler is generally set at about 40-45 degrees on air and land. If the indoor temperature is comfortable, it is necessary to adjust the setting value in combination with the outdoor ambient temperature, when the outdoor temperature is high, the floor heating boiler temperature can be set lower, and when the outdoor ambient temperature is low, the floor heating boiler temperature setting should be higher.

Kiss! The relevant extended information is as follows: under normal circumstances, after the installation of the wall-hung boiler is completed, the installer will debug, the general temperature is set at 45 degrees 55 degrees, if the floor heating design is reasonable, the condensing furnace can even be set at 35 degrees to achieve low-temperature radiant heating.

The temperature setting of the wall-hung boiler is related to the heating rate of the floor heating, but according to the long-term opening of the floor heating, the actual impact is not large. The temperature setting of the thermostat is related to the indoor temperature, the indoor temperature recommended by the General Principles of Civil Limb Building Design is between 18 degrees and 22 degrees, according to people's work and rest habits, the temperature of the living room area can be set at 20 degrees 22 degrees, and the temperature of the bedroom is set at 18 degrees 22 degrees.

1. Close all valves, the main inlet valve, the main return valve, and the branch valves.

2. Open the main valve and the branch valve of the water inlet.

3. Open the return water release valve.

Fourth, unscrew the farthest way of the release valve in the return branch valve.

5. Open the second valve after the air release valve flows out of the bubble-infested water.

6. After opening the valves of each branch in turn, close the air release valve.

7. Open the main valve of the return water, and the floor heating is turned on.

Simply plug in the water separator and adjust the temperature to the appropriate temperature on the control panel.

Main tools used: control panel, wrench, water separator, solenoid valve.

Specific steps:

Step 1: First, set up the indoor control panel, press the mode button to adjust the control panel mode to heating mode, and set the temperature to about 25 degrees.

Step 2: Use a wrench to open the water separator control valve, the main control valve of the inlet and return water must be parallel to the pipe, and make sure that the solenoid valve is popped up (the black part is raised).

Step 3: Power on and turn on the wall-hung boiler, if the wall-hung boiler has been in the boot state, you can ignore this step, and check whether there is an obvious fault problem when the wall-hung boiler is turned on.

Step 4: Finally, the wall-hung boiler should be set up, and the wall-hung boiler should also turn on the underfloor heating mode, and set the temperature to 55 60 degrees, and the pressure should be controlled between 1 and 2. At the same time, you should also pay attention to the pressure gauge index, if the pressure is too high, you need to relieve the pressure, and if it is too low, you need to replenish the pressure with water.

Precautions when using underfloor heating:

First, pay attention to the selection of materials

After laying the underfloor heating pipes, materials with low heat resistance, such as floor tiles, marble or composite wood floors, can be placed on the underfloor heating pipes; If you choose solid wood flooring, check that the wood flooring has been specially processed and can be used as a flooring material.

2. Exhaust excess gas before use

Underfloor heating systems require large amounts of gas to enter newly installed pipes and must be emptied before water can be used. Failure to discharge in time will affect the normal use of the system, so the correct step is to open the exhaust valve on the manifold, and after exhausting, tighten it.

3. The temperature should be set within a reasonable range

The water supply temperature of the floor heating pipe should not exceed 60 degrees, and the working pressure should not exceed 1MPa. Otherwise, the underfloor heating pipe is prone to shorten the life of the underfloor heating pipe due to the high water temperature or bursting due to excessive pressure.

The floor heating boiler can be turned on to 2-3 gears.

How to use floor heating boilers:

1. The pressure of the boiler in use should not be set too high When in use, the pressure of the boiler must not be set too high, usually kept in the suitable, once the pressure is too large, it will damage the service life of the sealing parts, when the pressure is too small, the system can not operate normally, adjust the pressure in the boiler, as long as the water is discharged after opening the vent valve, and the water can be added.

2. Do not mix hot water and cold water in daily life, the majority of users often mix hot water and cold water, which is no problem in the water heater, but if it is used on the boiler of floor heating, it will cause some adverse consequences, mainly because the hot water of the floor heating boiler is not directly heated, only after adding cold water will lead to a cyclic change in the pressure in the system, the inductor of the boiler will often reset the heating mode function of the system, which will cause the repeated use of the boiler. This accelerates the aging rate of the boiler.

3. Boiler cleaning and maintenance problems at the end of the winter, usually we need to maintain the floor heating will be cleaned, the user can operate in this way, first turn on the switch of water intake, and then increase the pressure to 2, when opening the drain valve, the dirty water will automatically flow out, so that the operation is repeated several times, until the water flowing out is clean, and finally the water inlet valve and the drain valve should be opened at the same time, after rinsing and washing, be sure to add clean water, Then adjust the pressure to it.

1. Household boiler firing method: fill the boiler with water, open the slag outlet, ignite the coal in the furnace, turn on the automatic switch to open, and then close the furnace door, and then see when you need to fill the coal.

2. Household boiler refers to the civil boiler used for home heating or bathing, which is small in size and low in energy consumption, and is typically suitable for family use. Household boilers are mainly wall-hung boilers and floor-mounted boilers. Families with buildings of less than 200 square meters mostly use household wall-hung boilers, and families with villas of more than 200 square meters mostly choose household floor boilers.

The temperature of the floor heating boiler is generally set at about 40-45 degrees.

The floor heating boiler uses the whole ground as a radiator, evenly heats the whole ground through the heat medium in the radiant layer of the floor, and heats the room through the heat transfer mode of radiation and convection through the ground to achieve the purpose of comfortable heating. According to different heat transfer media, it is divided into two categories: water floor heating and electric floor heating, and according to different pavement structures, it is mainly divided into dry floor heating and wet floor heating.

Generally, you can adjust the temperature of the boiler according to the temperature of the return water to about 55 degrees, and the temperature of the boiler can be adjusted according to the temperature of the return water.

Answer: If the temperature is relatively low in winter, we can appropriately adjust the temperature of the floor heating at this time, usually around 45 degrees is very suitable. If it's autumn or spring, it's okay to adjust the temperature to about 30 degrees Celsius. Of course, when using underfloor heating, we can directly set a predicted temperature, and after reaching this temperature, the underfloor heating will not work.

The radiator is usually the water heating, the wall-hung boiler or boiler is used to heat the circulating water, and then connected to the heat dissipation device through the pipe, the heat dissipation device is currently the most commonly used in the family is the radiator and floor heating pipe.

Generally speaking, the national standard indoor heating temperature is 18, and the design standard of central heating in most residential areas is as follows: 80 water intake, 60 water return, and 18 room temperature. If the water temperature is low, the heat dissipation of the radiator will be reduced, and the heat load required by the room will not be reached, and of course the indoor temperature will not rise.

If the user encounters a high temperature of the inlet and outlet water but the indoor temperature does not meet the standard, there may be two factors: one is that the heating area at home is large, but the number of radiators is not enough, although the radiators are already very hot, but the indoor temperature still cannot go up, so the user needs to increase the radiators appropriately. The second is that the radiator is enough for room heating, but the thermal insulation performance of the home is relatively poor, and the ventilation is larger, so the temperature is difficult to increase, which requires attention to the appropriate closure, strengthen the thermal insulation performance of doors, windows and walls.