You can t choose the wrong soaking brick and full tile, and find out what are the characteristics of

The raw materials for ceramic tiles are porcelain clay, clay, and quartz sand.

After the materials are mixed, they are made into tiles with different textures according to different technical techniques such as mixing ratio and firing temperature, and there are many varieties on the market. The whole tile has the lowest water absorption rate and low water absorption, which represents high mechanical strength, wear resistance, compression resistance and hardness. At the same time, the embryonic body does not absorb water, and the situation that we are most worried about during the use of ceramic tiles will never occur.

But there are also disadvantages: ** extremely high, the paste is not firm, and when paving, the tile absorbs the cement mortar.

The moisture in the cement can be adhered more firmly. The whole tile hardly absorbs water, which inevitably leads to poor pasting.

The water absorption rate of clay bricks is the lowest, but it also has the advantage of low - it is firmly pasted, almost the only tile that can adapt to the wall paving, and the half tile can barely stick to the wall, but the effect is not good, and it needs to be glued in the cement when necessary, which is very unfriendly to environmental protection. However, the low water absorption rate causes the clay bricks to be wear-resistant and unable to adapt to the water environment on the ground. Ceramic tiles are generally used in kitchens and bathrooms, and ceramic tiles are generally used in living rooms.

Generally speaking, kitchen and bathroom porcelain tiles need to be soaked in water before paving, and you can confirm with the shopping guide when you buy tiles.

Ceramic tiles with low density, because of their light weight, more pores, and dryness, are more suitable for wall surfaces when laying to avoid shrinkage and serious water absorption, and need to be soaked in water. Generally speaking, the tiles we buy need to be soaked in water before they are paved. At the same time, when purchasing, the main water absorption index of ceramic tiles, the higher the water absorption rate of inferior tiles, the surface will expand and crack, affecting the use of the effect, so pay attention to it before purchasing.

When the tiles are placed in the basin, be sure to glaze side up and the pottery side side down. If the glaze side is facing down, the corners of the tiles bump against each other, and it is easy to fall off the porcelain. When the bricks are fished out of the basin, the ground should be padded with a packing carton, and the tiles should also be placed with their backs against the wall with the glaze side facing up.

If it is reversed, the sharp corners of the glaze hit the ground, because the corners of the tiles are very brittle, and it is easy to knock off the porcelain.

Because there are many pores inside, soak the tiles in water before use, so as to ensure that the inside of the tiles is in a damp state. Then we dry the surface of the tile before using it, so that we can use cement mortar for pasting. After the cement mortar is pasted, these pores can be soaked through, and then the cement mortar will solidify normally.

If we do not soak this kind of soaking bricks, there will be a situation, that is, the moisture of the cement mortar used for paving tiles is quickly absorbed, resulting in the cement mortar can not be solidified normally and the strength decreases. The last thing that may happen is the bulging and falling off of the tiles. The biggest feature of the whole tile is that the water absorption rate is ultra-low, so the corresponding density is very high.

This brings a problem, that is, the requirement for the pasting of all tiles. This is also a feature that needs to be considered when applying full tiles. When we use ordinary ground to pave tiles, there is no problem with using cement mortar, because it is stressed downward and there is no problem of falling off.

The soaking bricks generally belong to the high water absorption rate of the tile, the water absorption rate of the soaking brick can be as high as 10%, the inside of the soaking brick has a lot of pores, so before using it to be soaked in the water, the water absorption rate of the whole tile is very low, the water absorption rate is only, the use of the whole tile is very extensive, the living room, kitchen and bathroom in the home can be used, the density of the whole tile is very high, and the requirements for pasting are of high standard.

In the process of decoration, the characteristics of soaking bricks and full tiles are different. The stickiness of the soaked brick will be better and will fit the wall. Pay attention to distinguish and avoid mistakes later.

When choosing tiles, we often hear the saying of "soaking water bricks" and "full tiles". Literally, many people believe that the quality of soaking bricks is not as good as all tiles, but in fact, this view is somewhat one-sided. In order to give you a better understanding of the two kinds of tiles, I will give you a good chat today.

The biggest difference between the two types of tiles is the water absorption。The water absorption rate of "full tile", the water absorption rate of "soaking brick" is usual. That is to say,"All porcelain" and "soaked water" represent the different characteristics of ceramic tiles, which are not directly related to the worst, so you can't see the soaked tiles, it is considered a poor tile.

<> because the water absorption rate of ceramic tiles is too high, it is easy to absorb cement mortar.

moisture, affecting the viscosity, so that the tile will be hollowed out in the future.

There is a high risk of shedding. Soak in water before tiling, so that the tiles can eat enough water, and reduce water absorption when paving, so as to make the tiles more stable and reliable. The water absorption rate of the whole tile itself is low, so when paving, there is no need to soak in water, and the cement mortar can be directly put on the wall.

The whole tile has low water absorption, high density, wear resistance and scratch resistance, which is not comparable to the soaking brick. But you should know that the higher the density of the tile paving will be very difficult, occasionally need to use glue to assist the paving, environmental protection and paving difficulty is higher than that of soaking bricks.

High hardness, wear-resistant, not easy to break. This is the biggest advantage of full tile, which is also one reason why most of the floor tiles choose full tile. All tiles have an ultra-high hardness and the surface is very wear-resistant.

The density of the soaking brick is very poor, there is a layer of glaze on the surface, after the glaze layer is worn, the tile is very easy to break, not stain-resistant. So, the ground is not an optionglazed tilesof them, only full tiles can be selected.

For the common type of soaking bricks, it is actually wall tiles. Some are pasted in our traditional family bathrooms.

Most of the glazed tiles on the wall belong to the soaked bricks. This type of tile belongs to ceramic tiles. In fact, soaking bricks are usually common in the stoneware bricks and fine-crushed bricks we mentioned above.

In fact, to put it bluntly, the water absorption rate is more than 3% . Personally, I think they belong to the category of soaking bricks. Most of these tiles need to be soaked in water before laying the characteristics of soaked bricks.

Foam bricks. There are many holes inside, so soak in water before use to ensure that the inside of the tile is in a damp state. Then we dry the water shade on the surface of the tile before use, so that we can use cement mortar for pasting. After the cement mortar is pasted, these pores can be soaked, and then the cement mortar will solidify normally.

If we do not soak this water brick, there will be a situation where the water of the cement mortar is quickly absorbed, resulting in the cement mortar not being able to solidify normally and the strength will decrease. Finally, the drumming and peeling of the tiles can occur.

Soaking bricks and full tiles must not be wrong, soaking bricks means that our tiles need to be soaked in water before paving. The conventional practice is to put the tiles into the bucket to soak the day before the tile is paved, and the whole tile does not actually refer to a kind of tile. This generally refers to what we often call polished tiles.

The water absorption rate of soaking bricks is very high, and the water absorption rate of full tiles is particularly low. The hardness of the whole tile is high, wear-resistant, and the hardness of the soaked brick is relatively low.

The color of the soaking brick is relatively bright and has a certain degree of water absorption. The full tile is more sturdy. You can choose according to yourself.

I believe that many owners have seen the decoration master soak the tiles they just bought in water when decorating, right? Good tiles, why soak in water? Won't soaking in water spoil the tiles?

Won't soaking in water damage the quality of the tiles? Today, I will tell you why the tiles are soaked in water? How to soak in water to qualify?

Why soak in water? 】

For this problem, I also consulted the company's supervision master, the tile will more or less have a certain pores, soaking in water before paving, in order to make its pores fully absorb water, and porcelain tiles due to the density is larger, the porosity is much smaller, which makes the water absorption rate very low. Especially for wall paving, before the wall is paved, it is necessary to sprinkle the wall, which is also the reason.

Do all tiles need to be soaked in water? 】

Yes, many people think that some bricks do not need to be soaked, in fact, comrades, do you think there is all porcelain now, many are fake, there is a bowl is real porcelain, translucent bowl real porcelain, the bowl is broken with black fake sandwich, so the tile should be soaked in water, soaked to not bubble can, pick it up and dry for a while, so good paste, too wet and not pasted, will slide down, the most important thing is that the reverse cement should be full, can not be empty, empty is easy to break!

How to soak in water to qualify? 】

However, many people may not be very clear about the specific practice of soaking in water for ceramic tiles, thinking that it is okay for tiles to be soaked in water, which leads to the phenomenon of hollowing and falling off after paving.

The correct way to soak the tiles in water is to find a large basin and let the bricks be completely immersed, but you must pay attention to handling them gently to prevent the porcelain of the tiles from falling off.

Place the tiles in a container of water and fill the container with water to cover the tiles. Generally, the duration of soaking in water is about twenty or thirty minutes, which is subject to the time when the tiles are completely soaked without bubbles.

Wrong case] Some construction teams in order to perfunctory, simply soaked, if the water has not buried the tiles, this practice is not correct, there may still be various problems after the tiles are pasted on the wall.

There are also workers, the tiles are stacked up and poured water on the top with a water pipe, so that the tiles can only be soaked, but not the tiles can fully absorb water, and there will still be hollowing and falling off after the tiles are paved.

Decoration of your own home, you can observe, if the decorator soaks the tiles in water like this, it is unqualified, and he will be let go immediately!

When soaking tiles, the glaze side is side up and the pottery side side is side down. This also avoids bumps. When placing tiles, there needs to be a paper skin on the ground.

How long does it take to soak in water? 】

The tiles must be soaked in water first, at least half an hour before construction, and all soaked in water, so that the bricks will not be deformed due to insufficient water absorption and unevenness, and the bricks are soaked in water saturation so that the bricks are more beautiful!

Finally, remind everyone that the tile can not be returned after soaking in water, after soaking in water, the color of the tile will also change to a certain extent, becoming slightly darker, and there will be a color difference with the new tile. In fact, it does not affect reuse, but most merchants will not give you a refund for the sake of profit. Therefore, the tiles should be soaked in water, and how much should be used to soak them.

Ceramic tiles are divided into porcelain according to water absorption (water absorption; Stoneware (commonly known as semi-porcelain: water absorption rate 10%); Tao 10%; Ceramic tiles are generally used in kitchens and bathrooms, and ceramic tiles are generally used in living rooms. Generally speaking, kitchen and bathroom porcelain tiles need to be soaked in water before paving, you can confirm with the shopping guide when you buy tiles, you can buy according to your own personal needs, it is recommended to compare the physical object with the Oushennuo physical store, I hope you can choose the right product for yourself.

1. The water absorption rate of ceramic tiles is relatively large, so there will be a corrugated image;

2. The position of the tile with corrugation may often be wet. Try not to touch the water in that place, if after a period of time, there will still be such a phenomenon, it is recommended to replace the brick.

Method 1: Choose a mop or rag with strong water absorption.

When we mop the floor tiles or wipe the tiles, it may be because the quality of the mop is not up to par and the water absorption is not strong, resulting in watermarks often leaving on the ground after mopping once, so we need to replace the absorbent mop or rag to clean.

How to drag a tile without leaving a watermark What to do if there is a watermark after the tile is wiped.

Method 2: Baking soda + dish soap.

We can add baking soda and dish soap to the water for washing the mop, then stir and mix, and then wash the mop, and keep the mop moist when mopping the floor for the first time, and we don't have to change the water too often, so as to ensure that all the stubborn dirt on the ground is dragged out; Next, use a dry sponge or rag to clean the dirty water on the ground, wash it and mop it again without leaving a watermark.

Hope it helps, dear

Hope it helps, dear

It's not that the quality of the tiles soaked in water is not good, the main thing is to see where it is pasted, if the wall tiles must be soaked in water, and the floor tiles do not need to be soaked in water.

Not. The ceramic tile soaked in water is mainly treated with water in front of the tile sticker, so that it can be pasted more firmly, and the construction is generally carried out in this way.

No, because many tiles need to be soaked in water before the ground, and the quality of the tiles will not be affected.

Of course, the quality of this soaked tile will of course be worse and worse.

Nowadays, wall tiles and floor tiles need to be properly soaked in water before laying them, especially those that are wet such as wall tiles, which need to be soaked thoroughly, otherwise it will affect the paste effect. The quality of ceramic tiles is generally linked to factors such as brand and quality. Master soaking water is not to say that the quality of your tiles is not good, some can not be bought, such as artificial stone, marble or something, radiation exceeded, this is to attract attention, as long as the other is of the same grade, basically the same, just like red bricks, yellow sand and other building materials, look at the eyes, the difference is not bad.

When the tile is used, it is necessary to soak enough water, which can increase the viscosity of the cement; Soaking in water before use not only adds weight but also prevents breakage.