Which is better, soaked tiles or non soaked tiles

Tiles soaked in water well.

The main reason for soaking ceramic tiles in water is to prevent the absorption of moisture from cement mortar, and if it is not soaked in water, it will cause the tiles to hollow, fall off, and even cracks. Especially for wall paving, it is also necessary to sprinkle the wall before pasting.

The tile itself has a certain pores, and soaking in water in advance is to allow its pores to fully absorb water, so that when paving, its water absorption rate is reduced to a minimum.

Tiles soaked in water well. The main reason for soaking ceramic tiles in water is to prevent the absorption of moisture from the cement mortar.

Why do tiles soak in water?

Before the tile stickers are sure to soak in water. Because there are many fine voids inside the tile, these voids have a certain water absorption. If you don't soak in water or soak in insufficient water, you will pave it directly, and the tile will absorb the moisture of the cement, so that there will be a gap between the tile and the cement, and the bond will not be firm, and it will cause the problem of hollowing or tile falling off.

It is good not to absorb water.

What absorbs water is glazed bricks, which is a layer of glaze on the surface of the clay after firing, and the quality is not good. Non-absorbent is all-porcelain floor tiles, ***. Exterior wall tiles are water-absorbing due to the relationship between materials, but there are standards for water absorption, and water absorption cannot be unlimited.

Too much water absorption is easy to cause the hollow drum to fall off.

The water absorption rate of this ceramic tile is relatively high, when using cement mortar paving, the purpose of soaking water is to prevent the ceramic tile that absorbs water from absorbing water in the case of not soaking in water, absorbing the water in the cement mortar too quickly after smearing the cement slurry, so as to shorten the solidification cycle of the cement mortar, causing the tile to be not firmly bonded.

It is better to soak tiles in water, and the main reason for soaking tiles in water is to prevent absorptioncement mortarmoisture. If it is not soaked in water, it will cause the tiles to dent, fall off or even crack. The tile itself has a certain pores, and there should be bubble water in advance, in order to make its pores fully absorb water, so that when paving, its water absorption rate will be reduced to the minimum.

The water absorption rate is less than the tile in the paving without soaking in water, glazed bricks.

The water absorption rate with floor tiles is generally greater than 10%, and it must be soaked in water when paving.

Precautions for soaking tiles in water.

1. Water depth. Choose a relatively large basin to blister the tiles so that there is enough water, and the depth of the water should not be lower than the height of the stacked tiles in the basin.

2. Tile stacking.

Put the tiles in the basin, and here is a reminder that you should pay attention to the glaze side up and the ceramic side side down. If the glaze side is facing down, it is easy to have that kind of tile corner due to the phenomenon of falling porcelain. After submerging in water, remember to remove the tile from the wash basin with the glaze side of the tile facing up as well.

Because if the sharp corners of the glaze are on the ground, it is easy to peel off the porcelain. The best way to do this is to place the cardboard box on the floor so that the tiles are pressed against the wall.

3. Soaking time.

Different tiles have different water absorption rates, so the soaking time is also different. For example, the higher the water absorption, the longer the soaking time. Check if the tile is "filled with water" and then you can see if the tile bubbles will blister.

4. Water temperature. As long as the water temperature of the tile is close to room temperature, be careful not to use too low water temperature, otherwise it will affect the water absorption rate of the tile.

All tiles are good.

1. From the perspective of hardness, the whole tile has high hardness, wear-resistant, and is not easy to break, which is also one of the reasons why most of the ground tiles choose the whole tile. All tiles have an ultra-high hardness and the surface is very wear-resistant.

And the tiles are very strong and not easy to break. Another point is that it has a very low water absorption, so it is very resistant to stains. The density of the soaked brick is very poor, and there is a layer of glaze on the surface, and after the glaze layer is worn, the tile is very easy to break.

2. From the perspective of type, in terms of tile type, all ceramic tiles are also better than soaking bricks.

soaked tiles and full tiles

The division of soaked bricks and full tiles is based on the water absorption. According to the water absorption, ceramic tiles can be divided into five grades.

If the water absorption rate is greater than 10%, it is called ceramic brick; The water absorption rate is 6% to 10% (inclusive), which is called stoneware brick; The water absorption rate is 3% 6% (inclusive), which is called fine stoneware brick; water absorption rate included), called stoneware tiles; The water absorption rate is less than or equal to, which is called full tile.

The water absorption rate is less than that of the tiles that do not need to be soaked in water when paving, and the glazed wall tiles and floor tiles used in the kitchen and bathroom generally have a water absorption rate of more than 10%, so it is necessary to soak in water when paving.

Prepare a large basin or bucket and soak all the tiles in water. Stack the tiles and pour water on them with a water pipe, so that you can only do the surface of the tiles to be wet, and the inside is still dry, and there may be hollowing and falling off after paving. Soaking in water will not drop the porcelain, but when you put the tiles in the water, be sure to put the pottery side down and the glaze side up.

If the glaze side is facing up, the tile corners are easy to bump into each other, resulting in porcelain dropping. When the tiles are taken out of the water, they should also be placed with their backs against the wall. If you put it in reverse, the sharp corners of the glaze will hit the ground, and it is easy to knock off the porcelain.

Since the water absorption rate of tiles of different materials is not the same, it should be waited until there are no more bubbles in the water. In hot weather, the soaking time should be longer; In the rainy season, the soaking time should be shorter.

Soaking in water will not drop the porcelain, but when you put the tiles in the water, be sure to put the pottery side down and the glaze side up. If the glaze side is facing up, the tile corners are easy to bump into each other, resulting in porcelain dropping. When the tiles are taken out of the water, they should also be placed with their backs against the wall.

If you put it in reverse, the sharp corners of the glaze will hit the ground, and it is easy to knock off the porcelain.

Precautions and key points for tile soaking:

Since the problem of wear and tear will be considered when buying tiles, they will buy more tiles. If the excess tiles are soaked in water, they cannot be returned, because the color of the tiles after soaking in water will become dull, and there is an obvious color difference with the original tile color. And the color of the tile soaked once will be different from the tile soaked in water for the second time.

Be aware of this.

Specifically, depending on the water absorption rate of the tile, according to the water absorption rate, the tile can be roughly divided into porcelain tile and ceramic brick, among them, the water absorption rate of porcelain tile is below, and there is no need to soak in water before paving; The water absorption rate of ceramic bricks is less than 20%, and it must be soaked in water before paving. Here are the specific types of tiles:

Need to soak in water bricks: glazed wall tiles, glazed antique bricks.

No need to soak in water bricks: vitrified bricks, polished tiles.

Ceramic tiles are divided into porcelain according to water absorption (water absorption; Stoneware (commonly known as semi-porcelain: water absorption rate 10%); Tao 10%; Ceramic tiles are generally used in kitchens and bathrooms, and ceramic tiles are generally used in living rooms. Generally speaking, kitchen and bathroom porcelain tiles need to be soaked in water before paving, you can confirm with the shopping guide when you buy tiles, it is recommended to compare the physical object with the Oushennuo physical store, I hope you can choose the right product for yourself.

Soak tiles and full tiles are commonly used types of floor and wall tiles, each with its own characteristics. Here's a brief rundown of both:

1.Soak the bricks

Soaking brick refers to a kind of decorative tile with a foam structure in the center and a stone or wood grain pattern on the surface. Because it is a foam structure in the middle, it is light in weight and easy to handle, cut and install during construction; In addition, due to the sound insulation effect of the foam structure, it can also effectively reduce noise when used. However, at the same time, there are also problems such as easy to fall off, easy to seep water, and poor impact resistance.

2.Fully tiled

Full tile refers to the whole tile blank is the same material of the tile, hard texture, with anti-chaos loss, strong anti-fouling ability, good waterproof and moisture-proof performance, and generally long service life. However, the hardness of the whole tile lacks silver, and the construction is difficult to install, requiring a high level of technology for cutting and installation, and because of its high level, it is generally not suitable for large-area applications.

Therefore, soaking bricks and full tiles have their own advantages and disadvantages, and the specific choice should be decided according to the actual situation and needs. If you pay attention to decoration, sound insulation, etc., and do not need to lay a large area, you can choose to soak in water bricks to accompany the banquet; If you pay attention to durability, moisture and stain resistance, etc., it is recommended to choose full tiles.