Soaking bricks and full tiles must not be wrong, what are the characteristics of each?

Updated on healthy 2024-07-25
13 answers
  1. Anonymous users2024-02-13

    When choosing tiles, we often hear the saying of "soaking water bricks" and "full tiles". Literally, many people believe that the quality of soaking bricks is not as good as all tiles, but in fact, this view is somewhat one-sided. In order to give you a better understanding of the two kinds of tiles, I will give you a good chat today.

    The biggest difference between the two types of tiles is the water absorption。The water absorption rate of "full tile", the water absorption rate of "soaking brick" is usual. That is to say,"All porcelain" and "soaked water" represent the different characteristics of ceramic tiles, which are not directly related to the worst, so you can't see the soaked tiles, it is considered a poor tile.

    <> because the water absorption rate of ceramic tiles is too high, it is easy to absorb cement mortar.

    moisture, affecting the viscosity, so that the tile will be hollowed out in the future.

    There is a high risk of shedding. Soak in water before tiling, so that the tiles can eat enough water, and reduce water absorption when paving, so as to make the tiles more stable and reliable. The water absorption rate of the whole tile itself is low, so when paving, there is no need to soak in water, and the cement mortar can be directly put on the wall.

    The whole tile has low water absorption, high density, wear resistance and scratch resistance, which is not comparable to the soaking brick. But you should know that the higher the density of the tile paving will be very difficult, occasionally need to use glue to assist the paving, environmental protection and paving difficulty is higher than that of soaking bricks.

    High hardness, wear-resistant, not easy to break. This is the biggest advantage of full tile, which is also one reason why most of the floor tiles choose full tile. All tiles have an ultra-high hardness and the surface is very wear-resistant.

    And the tiles are very strong and not easy to break. Another point is that it has a very low water absorption, so it is very resistant to stains. This is the biggest advantage compared to soaking bricks.

    The density of the soaking brick is very poor, there is a layer of glaze on the surface, after the glaze layer is worn, the tile is very easy to break, not stain-resistant. So, the ground is not an optionglazed tilesof them, only full tiles can be selected.

    For the common type of soaking bricks, it is actually wall tiles. Some are pasted in our traditional family bathrooms.

    Most of the glazed tiles on the wall belong to the soaked bricks. This type of tile belongs to ceramic tiles. In fact, soaking bricks are usually common in the stoneware bricks and fine-crushed bricks we mentioned above.

    In fact, to put it bluntly, the water absorption rate is more than 3% . Personally, I think they belong to the category of soaking bricks. Most of these tiles need to be soaked in water before laying the characteristics of soaked bricks.

    Foam bricks. There are many holes inside, so soak in water before use to ensure that the inside of the tile is in a damp state. Then we dry the water shade on the surface of the tile before use, so that we can use cement mortar for pasting. After the cement mortar is pasted, these pores can be soaked, and then the cement mortar will solidify normally.

    If we do not soak this water brick, there will be a situation where the water of the cement mortar is quickly absorbed, resulting in the cement mortar not being able to solidify normally and the strength will decrease. Finally, the drumming and peeling of the tiles can occur.

  2. Anonymous users2024-02-12

    Full tile characteristic. The biggest feature of the whole tile is that the water absorption rate is ultra-low, so the corresponding density is very high. This brings a problem, that is, the requirement for the pasting of all tiles.

    This is also a feature that needs to be considered when applying full tiles. When we use ordinary ground to pave tiles, there is no problem with using cement mortar, because it is stressed downward and there is no problem of falling off. However, for the pasting of wall tiles, it is generally not recommended that you directly use traditional cement mortar to paste the whole tile, but there is no need to soak in water.

    As a result, a new type of pasting material has emerged, that is, the back coating glue and tile adhesive of ceramic tiles.

    Characteristics of bubble bricks. Because there are many pores inside, soak the tiles in water before use, so as to ensure that the inside of the tiles is in a damp state. Then we dry the surface of the tile before using it, so that we can use cement mortar for pasting.

    After the cement mortar is pasted, these pores can be soaked through, and then the cement mortar will solidify normally. If we do not soak this kind of soaking bricks, there will be a situation, that is, the moisture of the cement mortar used for paving tiles is quickly absorbed, resulting in the cement mortar can not be solidified normally and the strength decreases. The last thing that may happen is the bulging and falling off of the tiles.

  3. Anonymous users2024-02-11

    Soaking bricks and full tiles must not be wrong, soaking bricks means that our tiles need to be soaked in water before paving. The conventional practice is to put the tiles into the bucket to soak the day before the tile is paved, and the whole tile does not actually refer to a kind of tile. This generally refers to what we often call polished tiles.

  4. Anonymous users2024-02-10

    The water absorption rate of soaking bricks is very high, and the water absorption rate of full tiles is particularly low. The hardness of the whole tile is high, wear-resistant, and the hardness of the soaked brick is relatively low.

  5. Anonymous users2024-02-09

    The color of the soaking brick is relatively bright and has a certain degree of water absorption. The full tile is more sturdy. You can choose according to yourself.

  6. Anonymous users2024-02-08

    The raw materials for ceramic tiles are porcelain clay, clay, and quartz sand.

    After the materials are mixed, they are made into tiles with different textures according to different technical techniques such as mixing ratio and firing temperature, and there are many varieties on the market. The whole tile has the lowest water absorption rate and low water absorption, which represents high mechanical strength, wear resistance, compression resistance and hardness. At the same time, the embryonic body does not absorb water, and the situation that we are most worried about during the use of ceramic tiles will never occur.

    But there are also disadvantages: ** extremely high, the paste is not firm, and when paving, the tile absorbs the cement mortar.

    The moisture in the cement can be adhered more firmly. The whole tile hardly absorbs water, which inevitably leads to poor pasting.

    The water absorption rate of clay bricks is the lowest, but it also has the advantage of low - it is firmly pasted, almost the only tile that can adapt to the wall paving, and the half tile can barely stick to the wall, but the effect is not good, and it needs to be glued in the cement when necessary, which is very unfriendly to environmental protection. However, the low water absorption rate causes the clay bricks to be wear-resistant and unable to adapt to the water environment on the ground. Ceramic tiles are generally used in kitchens and bathrooms, and ceramic tiles are generally used in living rooms.

    Generally speaking, kitchen and bathroom porcelain tiles need to be soaked in water before paving, and you can confirm with the shopping guide when you buy tiles.

    Ceramic tiles with low density, because of their light weight, more pores, and dryness, are more suitable for wall surfaces when laying to avoid shrinkage and serious water absorption, and need to be soaked in water. Generally speaking, the tiles we buy need to be soaked in water before they are paved. At the same time, when purchasing, the main water absorption index of ceramic tiles, the higher the water absorption rate of inferior tiles, the surface will expand and crack, affecting the use of the effect, so pay attention to it before purchasing.

    When the tiles are placed in the basin, be sure to glaze side up and the pottery side side down. If the glaze side is facing down, the corners of the tiles bump against each other, and it is easy to fall off the porcelain. When the bricks are fished out of the basin, the ground should be padded with a packing carton, and the tiles should also be placed with their backs against the wall with the glaze side facing up.

    If it is reversed, the sharp corners of the glaze hit the ground, because the corners of the tiles are very brittle, and it is easy to knock off the porcelain.

  7. Anonymous users2024-02-07

    The soaking bricks generally belong to the high water absorption rate of the tile, the water absorption rate of the soaking brick can be as high as 10%, the inside of the soaking brick has a lot of pores, so before using it to be soaked in the water, the water absorption rate of the whole tile is very low, the water absorption rate is only, the use of the whole tile is very extensive, the living room, kitchen and bathroom in the home can be used, the density of the whole tile is very high, and the requirements for pasting are of high standard.

  8. Anonymous users2024-02-06

    In the process of decoration, the characteristics of soaking bricks and full tiles are different. The stickiness of the soaked brick will be better and will fit the wall. Pay attention to distinguish and avoid mistakes later.

  9. Anonymous users2024-02-05

    The reason why some tiles should be soaked in water when paving, is to prevent the absorption of cement mortar moisture and cause the tile hollow drum to fall off or even cracks, some ceramic tiles are made of porcelain tiles porcelain tiles do not need to be soaked in water, the two are not much different in use, but their tile process has a certain difference.

  10. Anonymous users2024-02-04

    Why some tiles need to be soaked in water, mainly the water absorption rate of the tile itself is determined, and some water absorption rate is relatively large, so it is necessary to soak in water to avoid excessive water absorption rate resulting in infirm absorption of moisture in cement mortar. The difference between the two is actually quite large, and the most important thing is that the ceramic tile with a relatively large water absorption rate can better stick to this mortar.

  11. Anonymous users2024-02-03

    This is mainly related to the water absorption, the water absorption rate of different tiles is not the same, and the ceramic tiles with higher water absorption rate must need to be soaked in water.

  12. Anonymous users2024-02-02

    1. The main reason for soaking ceramic tiles in water is to prevent the absorption of moisture from cement mortar, resulting in hollowing, falling off, and even cracks in the tiles. Especially for wall paving, it is also necessary to sprinkle the wall before pasting.

    The tile itself has a certain pores, and soaking in water in advance is to allow its pores to fully absorb water, so that when paving, its water absorption rate is reduced to a minimum.

    2. Whether the tile needs to be soaked in water should be decided according to the water absorption rate of the tile itself. If the water absorption rate of the tile is less than 0 5, there is no need to soak in water when paving;

    Generally, the glazed wall tiles and floor tiles used in the kitchen and bathroom have a water absorption rate of about 10, and they must be soaked in water before paving. Soak all the tiles in water until they no longer bubble, and the length of time they soak is also related to the weather. It's a hot day, and it takes a little longer.

  13. Anonymous users2024-02-01

    Soak tiles and full tiles are commonly used types of floor and wall tiles, each with its own characteristics. Here's a brief rundown of both:

    1.Soak the bricks

    Soaking brick refers to a kind of decorative tile with a foam structure in the center and a stone or wood grain pattern on the surface. Because it is a foam structure in the middle, it is light in weight and easy to handle, cut and install during construction; In addition, due to the sound insulation effect of the foam structure, it can also effectively reduce noise when used. However, at the same time, there are also problems such as easy to fall off, easy to seep water, and poor impact resistance.

    2.Fully tiled

    Full tile refers to the whole tile blank is the same material of the tile, hard texture, with anti-chaos loss, strong anti-fouling ability, good waterproof and moisture-proof performance, and generally long service life. However, the hardness of the whole tile lacks silver, and the construction is difficult to install, requiring a high level of technology for cutting and installation, and because of its high level, it is generally not suitable for large-area applications.

    Therefore, soaking bricks and full tiles have their own advantages and disadvantages, and the specific choice should be decided according to the actual situation and needs. If you pay attention to decoration, sound insulation, etc., and do not need to lay a large area, you can choose to soak in water bricks to accompany the banquet; If you pay attention to durability, moisture and stain resistance, etc., it is recommended to choose full tiles.

Related questions
9 answers2024-07-25

Tiles soaked in water well.

The main reason for soaking ceramic tiles in water is to prevent the absorption of moisture from cement mortar, and if it is not soaked in water, it will cause the tiles to hollow, fall off, and even cracks. Especially for wall paving, it is also necessary to sprinkle the wall before pasting. >>>More

4 answers2024-07-25

Glazed bricks are divided into: ceramic embryo body glazed bricks and all-ceramic embryo body glazed bricks The water absorption rate is strong for the ceramic There are many pores on the back Drip water will disappear quickly Porcelain almost does not absorb water. >>>More

12 answers2024-07-25

It is not recommended to absorb the tile directly brush the adhesive construction Reason one, the absorbent tile directly brushes the adhesive, so the construction is not good, the absorbent tile is the decoration paste of the wall tile, also called the porcelain piece, some people do not know much about the wall tile material, the surface of the wall tile and the bottom of the billet is not the same material, that is to say, the surface material of the wall tile is good, it is not absorbent, the bottom material is rough, the water absorption is particularly high, such as the absorbent tile is not blistered, or the water absorption is insufficient, like this case, the tile can not be pasted on the wall.

15 answers2024-07-25

When we renovate a new house, we often use a lot of tiles. When pasting tiles, you need to use tile adhesive. >>>More

10 answers2024-07-25

A few days ago, a few tiles suddenly fell from the house, but fortunately they didn't hit anyone, which scared me to death! There is no problem with looking very stable during acceptance, but when the wall tiles are removed, it is simply caused by not shoveling the wall skin. I can't find the person in charge of the renovation, where can I reason? >>>More