How to remove dirt from car lamp covers?

Wipe it directly with soapy water, it will have a good cleaning effect, but it should be noted that you should never use laundry detergent water, because laundry detergent is corrosive, and soap is alkaline and will not corrode the lampshade. The advantage of this approach is that it is simple and hassle-free. Or use sandpaper dipped in water to gently polish off the aging lampshade layer, then apply a layer of polish, and finally spray a layer of clear oil to protect it.

The effect of this method is obvious, but not every place can be sanded clean, there are certain limitations, and it is not only the aging lampshade layer that is polished off, but also the protective film of the lampshade, which is still somewhat irreparable. Another way is to replace the lampshade directly, and if it is serious, use polishing.

1.Wet the lampshade with a watering can and wipe the dirt off the shade with a cloth.

2.Spray again and squeeze the toothpaste, squeezing a little more.

3.Wipe clean carefully.

4.After drying, waxing and polishing: this is also relatively common, and the average car detailing shop can do it.

The principle is to polish the lights with sandpaper and then polish them with a special wax. This method has obvious results, but it is not thrown everywhere, which is a disadvantage.

Long-term use will inadvertently leak a lot of dust into your car lights, precipitate a lot of stains. It not only affects the appearance, but also seriously affects the safety of the vehicle at night, now talk about how to clean the headlights.

in the dust. Turn on step-by-step reading mode.

Tool Material: Car Headlights. Method 1:

Remove the two rubber covers, remove the bulbs, and unscrew the two small lampholders.

Keep both bulbs and be careful not to touch the glass and not to break them, especially not to break them.

Cleaning tools required: 1 small bottle cap of dish soap.

Water, a rag, twenty or thirty grains of rice (not to fill the hunger, pour it into the lamp to increase friction.

Mix well and pour in. Shake vigorously dozens of times to clean thoroughly.

If you shoot from the bottom to the top, if you can see that there is a lot of dirt and dirt hidden in the lamp shell, shake it to a certain extent, it will be about the same.

Pour out the dish soap and rice water, and you can clearly see how much dirt there is. Rinse the inside with plenty of water, wash it five or six times until it is clear, and notice that a row of rice grains under the lamp shell is stuck underneath, but there is a solution.

Wrap some cotton in the wire and stick it out. Be very careful when wiping, the reflective material on the lamp bowl is more fragile than we imagine, and a little force will cause scars. Method 2:

Go to the tire repair area and remove the light bulb and blow it with an air pump to see if you can blow the dust off.

Use a straw to suck off the dust after removing the bulb.

Hello, glad to help you. You can choose to wash with dish soap water, or polish if that doesn't work.

It is not possible to clean the inside of the headlamp without removing the lampshade. When we clean the inside of the headlights, we should first cut off the power of the vehicle, and then remove the headlight lamp cover (the general owner himself cannot operate it, because the headlight lamp cover is sealed by glass glue and needs to be disassembled by professionals).

Then we can use hair dryers, rags, sponges and other tools to clean the headlight cavity. It should be noted that do not pour water directly on the inside of the lamp cavity, as this can easily cause a short circuit.

Precautions for the use of car headlights.

On roads where there is no central isolation facility or no center line, low beams should be used at night when meeting vehicles in the opposite direction at a distance of 150 meters from oncoming vehicles, and low beams should be used when meeting vehicles on narrow roads, narrow bridges and non-motorized vehicles.

When driving in close proximity between the vehicle behind and the vehicle in front of the vehicle driving in the same direction, the high beam lights must not be used.

If a motor vehicle breaks down on the road or a traffic accident occurs, obstructing traffic and it is difficult to move, the hazard warning flashing lights shall be turned on in accordance with the provisions and warning signs shall be set up at a distance of 50 meters to 100 meters behind the vehicle, and the illumination lights and rear position lights shall be turned on at the same time at night.

The internal cleaning of the headlights is more troublesome, and it is necessary to have a certain hands-on ability, and the methods are as follows:

1.Remove the headlight assembly;

2.Remove the bulb;

3.Use an appropriate amount of weak alkaline washing liquid to drop into the lampshade, use a suitable long strip, tie a towel or soft brush at the front end, and gently scrub;

4.After rinsing with clean water, dry or dry with a hair dryer (the temperature should not be high, it must be completely dry);

5.It's good to install restoration;

If there is dirt in the headlights, then it is along the edge of the lights, we have no way, if you dismantle the lights, it is easy to dismantle, and if you can't see clearly, you have to replace the headlights.

If there is dirt inside the car after hitting it, then the headlights should be removed from the car and wiped clean before putting them on, so that the dirt inside the headlights will be removed.

What should I do if there is dirt inside my car headlights? You can repair the car in the morning, thank you, just check it for you.

The method of cleaning the headlights of the car is as follows: 1. Clean the dust on the surface and wipe the headlight bank with a rag to be as clean as possible. 2. Cover the edge area of the headlights

Use tape to cover the edge area of the headlights, some cars only have some areas of fogging and hazy phenomenon, you can cover the area that does not need to be repaired to avoid unnecessary scratches. 3. Initial grinding: Immerse a piece of No. 1000 sandpaper in cold water for 10 minutes, evenly wipe the headlight shell, and polish back and forth in one direction to keep the surface moist at all times.

Pay attention to the appropriate force and do not damage the paint or decorative strips around the perimeter. 4. Re-polishing: Repeat the above work with No. 1500 sandpaper, but the grinding direction is different (if you polish up and down for the first time, this time it will be left and right), and still keep the sandpaper wet and polish the entire area.

After wiping it clean, repeat it several times with sandpaper No. 2000, No. 2500, and No. 3000. 5. Apply polishing agent: apply polishing agent on the plastic shell, polish in a circular way, repeat for about ten minutes, pay attention to the strength when polishing, prevent rubbing off the car paint, until the mirror surface is restored to the luster.

Summary. 1.Remove the headlight assembly; 2.Remove the bulb; 3.Use an appropriate amount of weak alkaline washing liquid to drop into the lampshade, use a suitable long strip, tie a towel or soft brush at the front end, and gently scrub;

How to clean the inside of this headlight? How do you clean the inside of a car headlight?

1.Remove the headlight assembly; 2.Remove the bulb; 3.Use an appropriate amount of weak alkaline washing liquid to drop into the lampshade, use a suitable long strip, tie a towel or soft brush at the front end, and gently scrub;

1. To remove the headlights, you need to screw them first and then disconnect the link between the headlights and the body; 2. Separate the lampshade from the headlight; 3. Drip the weakly alkaline water into the inside of the headlamp, and then gently clean the inside of the headlight with a soft brush; 4. After cleaning, wash it again with clean water, and blow it clean with a hair dryer on the inside of the headlamp after cleaning; 5. Install the headlights and lampshades.