What are the car light switches? What are the light switches on the car

The significance and use of each sign on each control lever of the headlight switch:

1。The headlights are turned off.

2。Width indicator light: that is, a small light, which is used when the weather is dark.

3。Headlight: Use at night.

Mode: Through the light sensor device in the car, the headlights are automatically switched on and off according to the outdoor brightness.

5。Front fog lights: used in foggy weather.

6。Rear fog lights: used in foggy weather to prevent rear-end collisions.

7。High beam: Dial this light control lever inward, the high beam will flash, push the light control lever outward to feel the "click", the high beam will always be on, and it will be automatically turned off when dialed back.

Adjust the brightness of the interior lighting.

1。As shown in the red circle icon in the figure below, this operation knob is used to control the instrument panel, center console, and interior lighting.

2。When the knob is in the position shown in the figure below, all the lighting in the car (instrument panel, center console, and interior lighting) is turned off.

3。When the knob is rotated upwards, the brightness of the display in the dashboard and center console will gradually increase.

4。When the knob is in the position shown in the red circle shown in the figure below, the brightness of the instrument panel and center console in the car will reach its brightest.

5。When the knob is in the position shown in the red circle shown in the figure below, the instrument cluster, center console, and all lighting in the car will be fully open.

Important note: Only in this state, can you turn on the roof light lighting! That's why you can't find the roof light switch anywhere else. Because it does not have a setting switch turned on alone.

The use of left and right turn signals is 8 said, the operation of all cars is universal, but a hint, if you gently lift the light control lever, the turn signal will automatically flash three times, which is to facilitate a short period of lane change overtaking, if the light control lever is dialed to feel "click", the turn signal will always flash, only the pull back will be closed.

The light control of the Japanese and German is completely different, so it is really difficult to do too much detail, it is recommended that you read the manual of your car, which is the most accurate guide to use.

The first floor may not have been driven by a car, it should be, the up dial is the right turn and the right tangent, the down dial is the left turn and the left tangent, the forward twist is to turn on the headlights, and then push forward is the high beam, the so-called overtaking lights are just the application of the turn signal, there is no such light.

From left to right: Rear fog lights, Front fog lights, Off status, small lights, low beams, Instrument lights.

Hello 01 The leftmost one is the light group switch; On the left, there are three low-beam, wide-width indicators, automatic lights and light off signs from top to bottom; On the far right are the high beams, turn signals, front and rear fog lights, and fog lights off signs. The knob headlight switch 01 is the same as the rotary lever headlight switch, but it is easier to operate than the latter. 

The car is equipped with various lighting and signal devices, in order to ensure the safety and reliability of the car, to illuminate the road, to indicate the width of the vehicle and the position of the vehicle, and to illuminate the interior of the cabin. Indication instruments and night vehicle maintenance, etc. In addition, in the case of turning, braking, meeting vehicles, stopping, reversing and other working conditions, bright or audible signals should also be emitted to warn pedestrians and other vehicles.

Automobile lamps and lanterns are divided into lighting lamps and signal lamps according to their functions; According to the installation position, it is divided into external lamps and internal lamps.

1. Exterior lamps.

Combined lamps, the car assembles the headlights, front turn signals, and front position lights together, which is called a combination headlight.

The rear turn signal, brake light, rear position signal, rear fog light, and reversing light are assembled together, which is called a combination rear light.

1. Headlamp.

Also called headlights or headlights, they are installed on both sides of the front end of the vehicle and are used to illuminate the road when driving at night. In order to prevent the strong light of the headlamp from dazzling the driver of the oncoming vehicle, the headlamp generally uses a double-filament bulb, that is, two filaments, high beam and low beam, which emit a high beam beam and a low beam beam respectively.

2. Position indicator light.

Position indicator lights are also called wide indicator lights and position lights; Mounted on the edges of the front and rear sides of the car to indicate the presence and width of the vehicle.

3. Fog lamps. Fog lights are installed at the head or rear of a car to improve the illumination of the road surface in conditions of fog, rain, snow or wind and dust.

The front fog lights are generally yellow or orange and are installed lower than the headlights. The rear fog lights are red to warn trailing vehicles to keep a safe distance.

4. License plate lamp.

The license plate light is installed above or on the left and right sides of the tail photo.

5. Reversing lights.

The reversing light is installed at the rear of the car, and when the gearbox is in reverse, it automatically lights up, illuminates the rear side of the car, and warns the rear vehicles and pedestrians at the same time.

6. Turn signal.

The main turn signals are generally installed on the left and right sides of the head and tail of the car to indicate the driving direction of the car. Generally, there are also side turn signals installed in the middle of the side of the car. Gradually, in small cars, side turn signals are installed in the exterior mirrors.

7. Brake light.

Also called a brake light, it is installed in the rear of the car. When the brake pedal is pressed, a strong red light is emitted to indicate braking.

8. a marker lamp.

Vehicles with an empty vehicle height of more than 3 meters are equipped with marker lights to indicate the contour of the vehicle.

Second, the internal lamps.

1. Dome light. Cars are generally equipped with a dome light, which is not only used as interior lighting, but also can also monitor whether the doors are closed reliably.

2.Meter lights.

Gauge lights are used to illuminate instrument panels. It is controlled by the main light switch, and the main light switch is turned on, and the instrument light is on.

3. Door lights. The door light is located at the bottom of the inside of the car's outward-fledged door, and when the door is opened, the door light illuminates to warn pedestrians behind you.

4. Reading light.

The reading light is mounted on top of the cockpit.

5. Luggage compartment light.

Installed in the baggage compartment, it will automatically light up when the baggage compartment is opened.

The light switch is in**? What do they all look like?

Before learning how to use the lights, novices must first understand what the switch of the lights is in and what styles they have. At present, there are two main styles of light switches on the market: knob type and paddle type.

What do the various headlight icons mean?

Now that we've figured out where the light switch is and how it works, it's time to figure out what the various icons on the light switch mean.

It should be noted that regardless of whether the vehicle's light switch is a knob or a lever, the high beam switch is on the left lever (i.e., the turn signal lever).

First, halogen lamps.

Halogen lamps can be said to be the earliest car headlights, and at present, this is also the most common car headlight lights, for some low-end models, they are basically equipped with halogen lights. Halogen lamps are basically the yellowing of the headlights, and from the perspective of lighting effects, halogen lamps have a darker color due to their relatively low color temperature. In the case of poor lighting, it can be seen that halogen lamps are different from xenon lamps, but there is no problem for normal urban driving.

The biggest advantage of halogen lamp is that it has strong penetration, in the case of fog and heavy rain and low visibility, the penetration ability of halogen lamp source is much higher than that of other products with high color temperature.

Second, xenon lamps.

Xenon lamp is currently a common form of car lamp used in high-end cars, because the brightness of xenon lamp is relatively high, it must be equipped with a lens, and the light emitted is very focused, so it is deeply loved by everyone, and the color is different from ordinary halogen lamps, and the light is white. The xenon lamp is very bright, the penetration is also good, and there is not much heat. But there are also disadvantages, slow lighting; A ballast is required, which may not be halogen-stable.

If the light is slow, the lamp language will not be easy to use; It's dangerous if the strobe fails.

If you choose a xenon lamp, you must not be spared the cost.

Thirdly, LED headlights.

At present, LED headlights are gradually entering people, but more often heard only LED running lights. However, due to the many advantages of LED headlights, they will slowly become the choice of car headlights. Energy-saving, environmentally friendly, durable, small size and other characteristics have become the choice of automobile headlights due to it.

However, at present, due to the constraints of structure and cost, it can only be applied to some high-end cars. The LED principle is the light-emitting diode, the PN junction. The principle is basically the same as that of xenon headlights, the difference is that there is no need for high-voltage ionization, because the positive and negative ions are directly placed in a fixed space, so it is more energy-saving and stable!

Lights are one of the important parts of automobiles and play a very important role in our driving process. If you drive a lot, do you know what types of car lights there are? Today, I will give you a detailed introduction to the types and functions of automotive lights.

1. Running lights: indicate the size of the direction.

In the first gear of the light switch, all the instrument lights in the car are lit up, and the front and rear lights will also be lit up. These two lights are not very bright, mainly to make the four corners of the body visible. Generally, the running lights should be turned on when it is getting dark, rainy, or in a shady place such as an underground parking lot.

2. Low beam: basically rely on it at night.

It is used at night when driving in the city. On the one hand, the roads of the city are illuminated by street lights, and there is no need for high beams to search the road surface in the distance, just to see the road surface conditions in front of the car; On the other hand, there is a large traffic flow on urban roads, and turning on the high beams not only causes the opposite driver to dazzle when meeting the car, but also affects the vision of pedestrians on both sides of the road.

3. High beam: suitable for wilderness.

High beams are suitable for use in the wilderness or on roads without street lighting, but they should be switched back to low beams when meeting cars to avoid dazzling the opposite driver. When the high beams are on, a striking blue light is lit on the dashboard to indicate this.

4. Turn signal: remember to use it when turning.

The most basic purpose of a turn signal is to alert others to the turn of a vehicle by signaling other vehicles and passers-by when it is turning. Sometimes turn signals can also act as lighting in narrow areas, so that the driver can see obstacles on both sides. When the turn signals on both sides are turned on at the same time, it plays a warning role.

5. Fog lamp: a helper for bad weather.

As the name suggests, fog lights are light signals used in heavy rain and foggy weather, and fog lights are more penetrating in fog, so they are easier for vehicles and pedestrians to notice early.

There is more than one switch on the lights of the whole car, so there is no such sign. The automobile light switch is marked with wide indicator lights, high beams, fog lights, turn signals, handbrake indicators, etc., which represent the turn prompt, the working status of the front and rear fog lights, the status of the vehicle high beam, and the handbrake parking indication.

The lights of the whole car light up the switch sign.

The headlight and width indicator light sign is used to show the working state of the vehicle's width indicator light, which is usually off, and when the headlight or width indicator light is turned on, the indicator light will be lit immediately. When the width indicator light is turned off or the width indicator light is turned off and the headlight is turned on, the indicator light turns off automatically.

High beam signs are used to show the status of a vehicle's high beams. The color of the high beam indicator is usually blue, which is easy to identify. In general, the indicator is off.

When the owner lights on the high beam, the indicator light will be lit at the same time to remind the owner that the vehicle is in use with the high beam. The fog lamp sign is used to show the working condition of the front and rear fog lights, and when the front and rear fog lights are lit, the corresponding signs of the indicator lights will be lit.

When the fog lights are turned off, the corresponding indicator lights turn off. Turn signal signs are used to show where a vehicle's turn signals are located. It is usually off.

When the owner lights on the turn signal, the turn indicator will be lit at the same time and flash in the corresponding steering direction to remind the driver that the turn signal is being used. The handbrake indicator is used to display the status of the vehicle's handbrake, which is usually off.

1。The headlights are turned off.

2。Indicator light: that is, a small light, used when the weather is dark3. Headlight: Use at night.

Mode: Through the light sensing device in the car, the headlights are automatically switched on and off according to the outdoor brightness. Front fog lights: used in foggy weather.

6。Rear fog lights: used in foggy weather to prevent rear-end collisions.

7。High beam: Dial this light control lever inward, the high beam will flash, push the light control lever outward to feel the "click", the high beam will always be on, and it will be automatically turned off when dialed back.

Rear fog lights, front fog lights, headlights (high beams, low beams), width indicators, instrument lights, turn signals, interior lights.

There are many light switches on the car, for example, headlights, headlights are used at night, and width indicators are small lights. Front fog lights, rear fog lights,

There are a lot of lights, including low beams, high beams, left turn signals, right turn signals, fog lights, double flashes, etc., pay attention to driving safety, you can understand the use of lights before driving. I wish you a safe entry and exit.

There are headlights to show width, fog lights in front of the lights, fog lights in the back, and high beams. Different lights are used in different states.

1。The headlights are turned off.

2。Indicator light.

3。Headlights. Mode 5. Front fog lights.

6。Rear fog lights.

7。High beams.

The lights on the car, the switch has low beam, high beam double flashing light.

The car has high beams, low beams, front and rear fog lights, left turn signals, right turn signals, roof lights, hazard warning lights, and wide indicator lights.

There are many lights on the car, such as left and right turn signals, headlights, fog lights, width indicator lights, and so on.