What to do if the plumbing leaks, how to deal with the plumbing leaks what to do if the plumbing lea

When there is a leak in the plumbing, turn off the valve on the manifold and call the HVAC company immediately**. Catch the leaking place with a bucket or basin, the water in the radiator will not be much, and it will run out after a while, which will not cause great losses to the decoration. Just ask the HVAC company to come and tighten the valve.

The place where the plumbing leaks is mainly the place where the manifold is grounded with the heating pipe and the radiator valve interface There will be water leakage, mainly because the plumbing is cold and hot during use, and the joint is easy to loosen, which mainly depends on the quality of the manifold and the radiator valve.

Whether the pipe is water floor heating or water radiator, the pipe under the buried floor is now a whole pipe, (the pipe between the manifold and the radiator), so there is a high probability of reducing the chance of water leakage in the plumbing pipe.

Now as the service life of plumbing pipes, the country has clear regulations, the service life of floor heating pipes must reach 50 years, which is basically equal to the life of the house. Therefore, if the quality of the project is qualified, it will not leak.

After the completion of the construction of water and floor heating, the plumbing pipeline will be pressed to the test, and the pressure of the pressure test will be 2 or 3 times higher than the normal pressure until the decoration is completed. If there is a problem with the plumbing, it will be discovered during the renovation process.

Find the former owner, whether he is useful or not, you buy a house and must have the floor heating is the money, then it is quite that you pay for things that cannot be used, this is like you spent money to buy a car, the engine is pregnant, he said that he has not driven, you will not find him responsible?

1. First of all, it is necessary to understand the cause of water seepage, and then solve it in combination with the cause. Close the heating valve first, and then open the air valve, and empty all the pressure inside.

2. It may be that the pipeline has been used for a long time, and there are some trachoma causing water leakage, which is not difficult to deal with. Prepare an inner tube of the bicycle, wipe the surface clean, then stretch it in the leaky place, buckle it, and then tie it tightly with a wire, it will rust to death after a long time.

3. The water leakage is not particularly serious, and the surface can also be wiped clean first, and then pasted with a special sealant, which can play a role in sealing. In addition, glass glue can also be used, it is best to choose neutral, otherwise the acidic one will have a corrosive effect.

4. If the water leakage is more serious, in this case, it is best to replace it with a new pipe, replace it with PE material, its pressure resistance is better, and then wrap the raw material belt, wrap it a few more times, and finally wrap it with aluminum foil.

5. If there is a problem of water leakage at the head, the joint needs to be replaced, especially at the interface of the valve, which is most likely to leak.

6. If there is water leakage in the sensitive valve, it may be that the sealing ring inside is damaged and damaged. You need to replace the gasket and reinstall it again.

7. If you don't know it, you can only ask professional personnel to come to solve the maintenance.

Summary. Dear, hello, I have inquired for you what to do if the heating is leaking over the water If it is a regular pipe leakage, you can find a hoop, wrap it with a raw material belt, and then hold it tightly with a hoop. Irregularities are more troublesome.

It's time to burn spot welding. Due to the general pipe network in the early stage of the water test is all cold water, the principle of thermal expansion and contraction will lead to water leakage at the connection of the heating pipe, in this case, the general water pressure will not be too large, the user can use a towel or rag to gently wrap the pipe, leave a section and put it in the basin, let the water flow into the basin, and then find professionals to repair, do not deal with the maintenance by yourself, once the operation is improper, the connection will cause you greater losses.

Hello, I am a designer who has been engaged in the furniture industry for 10 years, and I have paid for craftsmen all my life Familiar areas include chain limb search public decoration, residential, curtain wall three major sub-industries, and I am proficient in hunger. Design, construction, maintenance and maintenance of interior and exterior decoration works. We'll be happy to answer for you.

Hope it helps you <>

Dear, hello, I have inquired for you what to do if the heating is leaking If it is a regular pipe leak, you can find a collar to read the hoop, wrap it with a raw material belt, and then hold it tightly with the hoop. Irregularities are more troublesome. It's time to burn spot welding.

Due to the early stage of the water test, the general pipe network is injected with cold water, the principle of thermal expansion and contraction will lead to the heating pipe connection is prone to water leakage, this situation is generally not too much water pressure, the user can use a towel or rag to gently wrap the pipe, leave a section and put it in the basin, let the water flow into the basin, and then find professionals to repair, do not deal with the maintenance by yourself, once the operation is not done properly, the connection will cause you greater damage and loss.