How to put the 90 degree line of floor tiles, and paste floor tiles at home. How do you get started?

Updated on home 2024-07-13
16 answers
  1. Anonymous users2024-02-12

    How to put the 90-degree line of the floor tile, please follow the steps below;

    Now it is generally put with a theodolite, find a long side of the two lines on a dozen on it, accurate, no instrument can only teach you according to the following traditional methods, such as reading mathematics is good according to the square root calculation is the most accurate.

    If it is square from the longest wall, take the side length of a brick, such as 300 vitrified bricks, 600 put 800, and so on, after this line is straightened, press this and then pull out the side length line of the brick on the top of the horizontal, the following is the key point Please note; From the inner angle of the two lines you pull as a starting point, pull a ruler along a line to pull a 3 meters, another line to pull a 4 meters, make a mark, and then pull 45 degrees obliquely is exactly 5 meters, how to adjust to the accurate data without me to teach, right? (Note; The 3 meters, 4 meters, and 5 meters mentioned here can be arbitrarily changed to centimeters, millimeters, etc., and all the numbers can also be enlarged or reduced by common multiples) I don't know if this explanation can be understood.

    Hope it helps.

  2. Anonymous users2024-02-11

    90 degree line pay-off method:

    The theodolite method is as follows:

    The first step: first adjust the theodolite to zero, and then turn the instrument horizontally to play 90°;

    Step 2: Then lock the transverse spiral (the transverse spiral, the upper and lower spirals are composed of 2 spirals, such as the transverse helix, a large one is used to lock, the instrument cannot move, and then the small spiral is adjusted for fine-tuning);

    Note: This process is to be recorded.

    Traditional method: the first step: if it is square, take the side length of a brick from the longest wall, such as 300 vitrified bricks, 600 put 800, and so on.

    Step 2: From the inner angle of the two lines you pull as a starting point, pull a ruler along a line for 3 meters, and another line for 4 meters, make a mark, and then pull 45 degrees diagonally to exactly 5 meters, in fact, it is a Pythagorean theorem (Note; 3 meters, 4 meters, 5 meters, can be arbitrarily changed to centimeters, millimeters, etc., all numbers can also be enlarged or reduced by common multiples).

  3. Anonymous users2024-02-10

    Laser line-projector is commonly used, which is fast and accurate.

  4. Anonymous users2024-02-09

    Hello, if you stick the floor tiles at home, you should first hit the horizontal line around, and you can start drying after shooting the bricks from the door to the inside, and the tools should be level, level, small line, ink fountain, ash shovel, marker, and other tools.

  5. Anonymous users2024-02-08

    Two adjacent corners can be laid out in the size of a brick and adjusted to the square.

  6. Anonymous users2024-02-07

    There are two kinds of laying floor tiles, one is to put the horizontal line, you can use a horizontal pipe or a cross base, the purpose is to keep the finished surface of the tile horizontal, and there is also a kind of layout formwork pay-off, because according to the specification requirements of the smallest tile block can not be less than the width of the tile 1 3, if you go along the narrow strip may not be beautiful, if the geometric size of the room is not good (the yin and yang angle is not vertical, may be caused by the wall or plastering), there may be a "mouse tail", the narrow strip is also counted, but also the size of the head, it will be fatal. It is best to be assisted by experienced professionals to assist you, not three or two sentences can be explained, the specific situation is analyzed, the layout of the mold according to local conditions, the wall and floor tiles of the bathroom and kitchen are best to climb the wall if there are conditions, the ground joints, the wall joints are smooth, beautiful and generous.

  7. Anonymous users2024-02-06

    Find vertical, horizontal, and line according to a corner of the wall, and the other walls will go like this!

  8. Anonymous users2024-02-05

    First, the tiling is in accordance with the landlord's point of view, the direction of the selection of the tiling, there is a square, there is a diamond paving, well, determine the square of the brick, how to estimate and measure whether the wall of the house is a right angle of 90 °, this problem is very big, this is experience, do not test, a little room corner width is not the same, resulting in the size of the paving is different, very affecting the appearance, after the test, remember the size of each room, to estimate the cut of the tile, mainly keep a line and the same size and then test the horizontal line on the wallKeep the ground level, the problem in the future is sand cement, it is easy to work with confidence

  9. Anonymous users2024-02-04

    I don't know if you are a wall tile paving or floor tile, if you are a wall tile, you should first find out the horizontal line and vertical line on the wall The bottom row of the bottom brick requires the size of the processing to master the level of the paving If you require seamless paving and pasting, you can use a toothpick to pad the gap in order to achieve the uniformity of the tile joint Require the joint to be paved You need to prepare a special cross card for tiles in advance If you need to re-plan the floor tiles according to the design of the house I hope you can be satisfied I hope I hope to help you.

  10. Anonymous users2024-02-03

    Find out the longitudinal and transverse center points of the room, put the "ten" line, and calculate whether the first row of bricks is singular or even by the size of the bricks, the singular number has 1 brick with two corners facing the central axis, and the even number is on both sides of the central axis, that is, one piece on the left and one piece on the right.

  11. Anonymous users2024-02-02

    Give me a mausoleum-shaped pay-off figure to show my mom.

  12. Anonymous users2024-02-01

    Is it right to give a graph?

  13. Anonymous users2024-01-31

    It's actually quite simple.

    You just use a small transparent hose and fill it with water, leaving a little bit empty at both ends and not filling it up (don't have air in the pipe).

    In the room where you want to stick wall tiles, choose a random point as the base point (arbitrary height), one person taps the end of the water level at one end of the water pipe on the base point (assuming point A), and the other person takes the other end and holds it on the yin (yang) corner (assuming point B) and moves it up and down; When the water level at point A overlaps with the base point, stop; mark point B, mark all the yin and yang corners of the room in turn.

    Flick the ink fountain line.

    So a flat water line comes out.

    When pasting bricks, you only need to use the line as the basis to measure it with a ruler, considering that you don't have the foundation in this area, it is best to pass three lines, a horizontal seam, a vertical seam, and a brick surface.

  14. Anonymous users2024-01-30

    1.Use a small transparent water pipe to leave a little empty at both ends of the fiber and do not fill it, and the water in the pipe should not have air.

    2.Select any point in the room you want to tile as the base point. Highly casual.

    3.A person taps the end of the water level at one end of the pipe on the cardinal point, assuming point A.

    4.The other person holds the other end on the yin corner, assuming it is point b.

    5.Move up and down, stop when the water level at point A overlaps with the base point, and mark point B. Mark all the corners of the room in turn.

  15. Anonymous users2024-01-29

    There are two pay-off methods for paving floor tiles, one is to use instruments, one is to pull the line, in different decoration scenarios, the two pay-off methods are very practical, and the two pay-off methods used by the third are both accurate and square.

  16. Anonymous users2024-01-28

    Generally, put a horizontal line and use the horizontal line as a reference line! Each horizontal row and vertical row should be put a line, pay attention to whether the interface of each brick is aligned when paving!

Related questions
29 answers2024-07-13

It is also possible to veneer wooden floors. Wood flooring refers to flooring made of wood, and the wood floors produced in China are mainly divided into six categories: solid wood flooring, laminate flooring, solid wood flooring, multi-layer laminate flooring, bamboo flooring and cork flooring. >>>More

5 answers2024-07-13

In home decoration design, most families attach great importance to the decoration design of the ground, and many families choose floor tiles for decoration in the selection of ground decoration materials. Floor tiles are very common and are the most classic floor decoration materials. In daily life, we will inevitably drop stains on the floor tiles, and we will have questions about how to remove the stains on the floor tiles. >>>More

4 answers2024-07-13

The varieties of floor tiles include full-body bricks, glazed tiles, full-body polished tiles, infiltrated tiles, infiltrated polished tiles, etc. When it comes to the color matching of floor tiles, it is still determined according to the decoration style of the home. There are also house types to design. >>>More

10 answers2024-07-13

Use a mop and add some oleace to mop. 1. Keep the floor dry and clean, and it is not allowed to wet the mop with water or scrub with alkaline water and soapy water, so as not to damage the brightness of the paint and damage the paint film. If it is dusty or dirty, wipe it with a dry mop or a wrung out wet mop. >>>More

5 answers2024-07-13

Avoid the color difference of the floor tiles:

1. We must carefully check the batch number and color number when accepting the ceramic tiles. If you find a product with different batches and color numbers, you should notify the seller in time or refuse to accept the batch of goods. >>>More