How can the words glued to the wall get down without affecting the wall

Don't stick it directly with glue, just brush the wall with a base film before pasting, so that if you tear it off later, it won't damage the wall. Roll the wall with water and wait for five or ten minutes to soak the wallpaper, and it will be easy to tear off. Blow it with a hair dryer and hot air, and it should be easier to tear some.

1. The wall treatment must be smooth and clean. If there are bumps or cracks on the wall, it should be removed with a shovel, smoothed with putty, and then sanded with sandpaper after drying. When treating a large area of wall, it is best to use old powder and cooked rubber powder to make the wall more firm; For small areas, such as repairing joints, gypsum powder can be added with some clear oil to make putty.

2. Completely remove the glue stains of the old wallpaper, etc., if the wall has been damp, it is best to use fungicides for special treatment to kill mold.

3. If one side of the wall is a bathroom, the inner wall of the bathroom must be specially treated with waterproofing agent, otherwise the wall will be damp for a long time and the wallpaper glue will fail.

4. It is recommended to brush the wall with the base film at most twice to protect the wall and prevent moisture. After drying, gently sand it with sandpaper. Do not brush the base film too much, as this will cause the wall to be too smooth, causing the wallpaper to stick firmly and shrink during the drying process to create joints.

5.The wall treatment is to make the wall surface flat, clean, dry without cracks and cavities, solid and free of floating dust.

6. Cement and brick walls: the wall surface is relatively flat, flattened with putty, and the wallpaper can be pasted after the thin base film is brushed and dried.

Removing the hair dryer after heating will not damage the wall.

Only if the wall is broken, then use putty powder on it, which is also very simple.

How do you remove stickers on the wall?

1. Mix dish soap and water and apply it to the label, so that the label can be completely wet; Then cover the label with plastic wrap so that it can be sealed thoroughly, wait for about 5 minutes to remove the plastic wrap, and you can see that the label can fall off with a slight pull. When doing these cleanings, it is good to remove the packaging on it, such as the paper scraps on the stickers or the plastic film on the security label.

2. Apply the wind oil essence to the residual glue; Paper towels (or anything else that can be wiped, but it's better to choose a cheaper one) just wipe it back and forth. This method will make the residual glue thinner, but because of the oiliness of the wind oil essence, there is a layer of greasy on the object, and if you hate it, you can use the greasy dish soap to wash it again.

3. Soak it in hot water for a while, or use a hair dryer to blow it off, and then you can remove it. In winter, the weather is cool, and it should be covered for a longer time, and it will be better to uncover it when the weather is warmer.

When we learn how to put stickers on the wall, we can put the stickers beautifully. Similarly, if you learn how to remove stickers, there will be no unsightly marks left on the wall.

1. Ironing method.

You can cover the old paper with a soaked cloth first, it is best to wring the damp cloth to squeeze out the water first, and iron it with a common iron, and the paper on the wall will be easily removed.

2. Dry wet method.

Wet the wallpaper with a sponge dipped in water, then slowly peel it off.

Remove the sticker with dish soap and plastic wrap.

Apply an appropriate amount of dish soap to the sticker, cover the sticker with plastic wrap, and smooth it with your hands to squeeze the air out.

After 5 minutes, remove the plastic wrap and easily remove the sticker with little effort.

1. Preliminary attempt by hand: when taking the strong sticky hook, you can first use your hand to take the sticky hook to see if it can be removed, and pay attention not to use too much force in this process to prevent damage to the wall.

2. Use a hair dryer to blow: If the viscosity is too big and can't be removed by hand, you can use the high temperature of the hair dryer to blow on the sticky hook to be taken off for 2-3 minutes (the specific time is subject to the softening of the viscose), and after the viscose is softened, you can take off the sticky hook first.

3. Scrape with a blade: After the sticky hook is removed, there may be glue marks, at this time, use a knife to slowly hang up the glue marks on the wall little by little, pay attention and do not scratch the wall, you can also spray the flower water first, and then scrape with a scraper.

4. Apply toilet water: After feeling that it is almost scraped with a knife, spray with toilet water and soak for 10-20 minutes.

5. Wipe with a rag: After soaking in the toilet water, wipe the glue marks with a rag to wipe off the glue marks, if it is on a wooden wall, you can repeatedly apply the toilet water 2-3 times in a row, and wipe with a rag.

6. Suggestion: In the process of cleaning, it is necessary to scrape, wipe lightly, and repeat many times to prevent excessive force from damaging the wall, and the gains outweigh the losses.

I seem to have heard of such a method、Apply some dish soap on the top of the sticker.,Cover it with a layer of plastic wrap.,Let it sit for a while.,And then tear it off.。。。 You can try it ...

Blow it with an electric hair dryer for a while, heat up the area with glue and gently remove it.

Stick it down with a cloud of clear glue as well.

Try rubbing it with soap dipped in water.

Use a hair dryer to blow hot air and then tear it off.

Eraser works well

After drying it with a hair dryer, it is easy to tear off and does not hurt the walls.

Here are a few ways to do ...... that I hope will help you

1. Grind it off with sandpaper.

1. Apply the face oil, wipe it evenly, first pick it off with your fingernails, and then wipe it off with a wet towel.

2. Use a hair dryer to blow the glue and bake it hot.

3. Wipe it with wind oil essence, and it will fall off after a while, try it.

4. You can try the eraser. But at the beginning, you may feel that the more you rub, the dirtier it gets, but if you wipe it for a longer time, you will see the effect.

5. Soak it in water, put a little dish soap, and then brush it with an old toothbrush.

6. It is also OK to wipe it with a cloth dipped in alcohol or a second pot head.

9. Wipe it off with a little sodium water, or use paint thinner 10. Wipe it with a cotton swab dipped in nail polish.

One: for the latex paint wall, you can use a hair dryer to heat it properly, (not continuous heating, because the glue on the back of the wall sticker will be easier to deglue when tearing because of excessive heating) When the temperature reaches about 40 degrees, you can try to tear the corners by hand, if you don't find degumming, you can slowly tear off, and the old beam can be gradually removed according to the above methods for relatively large styles. This method can avoid tearing off the wall paint together, but it is possible that a very small part of the glue will remain on the wall.

Two: for the wallpaper on the wall sticker, if it is PVC wallpaper, it can be torn off according to method one, for a small part of the glue can be scrubbed clean, if it is pure paper wallpaper and non-woven wallpaper, it is not recommended to remove the wall sticker. There is currently no effective method.