The gap between the tile and the gypsumboard ceiling is too ugly, is there a complete solution?

The gap between the tile and the gypsum board ceiling is too ugly, and the solution: there are many main reasons for the cracking of the gypsum board, including the construction technology of the workers is not up to standard, or the moisture content of the purchased gypsum ceiling.

High, waiting to move in, there is a possibility of cracking of the plasterboard on the paper. For example, the moisture content of gypsum ceilings.

It is very high, so most of the time you can't see anything at the beginning of installation, but when you move in, the temperature rises and dries, so the gypsum ceiling may crack. First of all, everyone should apply plugging putty powder.

to fill the gap and make up the gap in the gypsum ceiling;

Then wait for dryness, and then use a telescopic cloth to stick to the gap, and apply cost-effective white glue to make up for it; Although after the gluing is done, everyone starts to batch putty, and then sprays latex paint.

That's it. We first need to clean the loose plaster in the gaps, expand the gaps, and then apply a vacuum cleaner.

Clean up the remaining small dust and other dirt; Next, the gap between the gypsum board is wetted, and the mixture of thick plaster and water is irrigated to scrape the gap between the gypsum board; Wait for more than 24 hours, and then apply a relatively fine abrasive cloth to gently polish and polish it to make it more flat.

Then apply the primer, and then apply the paper gypsum board wall paint. The strength characteristics and deformation of gypsum board are determined according to the orientation, and the vertical characteristics of the board will be better than the horizontal, so the main keel of the vertical and sandwich surface of the gypsum board can be used when decorating the ceiling.

The parallel plane, which is vertical with the main keel, is also the main countermeasure to avoid deformation and cracking at the joints.

in the installation of lightweight partition panels.

When it is necessary to pave vertically, because of the vertical length of the board and the height of the building.

It is advantageous to be identical or close to each other, and to be fixed with the vertical keel, and the joints of the vertical pavement are beneficial to improve the level of fire safety. Before the formal construction, the workers have to use the horizontal pipe to determine whether the sketch line of the wall bomb is level, only to ensure that the basic line is indeed level, so that the subsequent installation of the decoration ceiling will not cause skew or there are many ups and downs. The gypsum ceiling must be fixed on a stable wooden main keel frame, so the careful selection of the keel material has become an indispensable step, and it is proposed to choose the fir material with better wear resistance as much as possible.

When carrying out the ceiling, it is necessary to choose a better size, and if the gap between them is relatively large, it should be rectified again. It doesn't matter that way.

Oil metal profiles, where we can see, leave a centimeter, so that the gap between the tile and the plasterboard flows to the upper gap, which we normally can't see.

The gap can be filled with plaster and completely filled with a sewing tool.

Summary. Dear, hello, I am glad to answer the joint between the plasterboard and the tile so that you can use glass glue, the steps are as follows: 1

First of all, you need to be able to use a glue gun; 2.Determine the width of your glue, that is, the width of the gap; 3.According to the width of the gluing gap, cut the glue nozzle into a slightly smaller diameter than the gap; 4.

Do a good job of protecting both sides of the glue gap, and paste 2-3cm adhesive tape on the materials on both sides of the gap, which protects the materials on both sides and is also very convenient for correcting the glue in the gap; 5.Master the speed of gluing and the speed of the movement of the glue gun, and move the glue gun evenly according to the depth of the gap; 6.Glue area trimming, how to deal with the joints between gypsum board and tiles Gypsum board ceiling and wall tiles.

Dear, hello, I am glad to answer the joint between the gypsum board and the ceramic tile so that you can use the brother glass glue, the steps are as follows: 1First of all, you need to be able to use a glue gun; 2.

Determine the width of your glue, that is, the width of the gap; 3.According to the width of the gluing gap, cut the glue nozzle into a slightly smaller diameter than the gap; 4.Do a good job of protecting both sides of the glue gap, and paste 2-3cm adhesive tape on the materials on both sides of the gap, which protects the materials on both sides and is also very convenient for correcting the glue in the gap; 5.

Master the speed of gluing and the speed of the movement of the glue gun, and move the glue gun evenly according to the depth of the gap; 6.Glue area trimming spine dust change, dear, if my answer is helpful to you, please also give a thumbs up (in the lower left corner of the evaluation oh Yu sleepy), look forward to your like, your efforts are very important to me, your support is also the driving force for my progress. If you feel that my answer is still satisfactory, you can close the void reed and click on my avatar for one-on-one consultation.

Finally, I wish you good health and a good mood!

How to deal with the junction of gypsum board and cement wall.

The junction of gypsum board and cement wall is treated like this, and the joints of gypsum board and cement wall are putty treated.

How to deal with cracking.

Pro-glass glue can be used.

Is it okay to use glass glue for the joints of gypsum board and cement walls?

Yes pro. Good.

Dear, if my answer is helpful to you, please also give a thumbs up (comment in the lower left corner), look forward to your like, your efforts are very important to me, and your support is also the driving force for my progress. If you feel that my answer is still satisfactory, you can close the void reed and click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

Plasterboard ceilings.

Joints with tile walls can be made with glass glue.

First of all, you need to be able to use a glue gun; Determine the width of the glue, i.e. the width of the gap.

According to the width of the gluing gap, cut the glue nozzle into a slightly smaller diameter than the gap; Do a good job of protecting both sides of the glue gap, and paste 2-3cm adhesive tape on the materials on both sides of the gap, which protects the materials on both sides and is also very convenient for correcting the glue in the gap;

Master the speed of gluing and the speed of the movement of the glue gun, and move the glue gun evenly according to the depth of the gap; Trim the gluing area, find a shovel to scrape the uneven places, and repair the glue where there is no gap when gluing; After 48 hours, remove the adhesive tape on both sides of the material to complete the construction.

Gypsum board ceilings and tile wall joints can be made of glass glue. First of all, you will be able to use the inside of the glue gun; Determine the width of the glue, that is.

Accommodating the width of the gap.

According to the width of the gluing gap, cut the glue nozzle into a slightly smaller diameter than the gap; Do a good job of protecting both sides of the glue gap, and paste 2-3cm adhesive tape on the materials on both sides of the gap, which protects the materials on both sides and is also very convenient for correcting the glue in the gap;

Master the speed of gluing and the speed of the movement of the glue gun, and move the glue gun evenly according to the depth of the gap; Trim the gluing area, find a shovel to scrape the uneven places, and repair the glue where there is no gap when gluing; After 48 hours, remove the adhesive tape on both sides of the material to complete the construction.

Gypsum board ceilings are generally used in the decoration of the living room, and there are many gypsum board ceiling shapes. When designing gypsum board ceilings, how to design will be based on the space structure and decoration style of the living room. The height of the living room should be considered when designing the gypsum board ceiling to prevent the living room from causing a sense of oppression.

Let's take a look at the gypsum board living room ceiling modeling**, and talk about how to design the gypsum board ceiling in the living room.

First, the gypsum board ceiling should consider the living room space.

How to design a gypsumboard ceiling in the living room? When designing the gypsum board ceiling in the living room, the space structure of the living room should be considered first, and the shape of the living room is generally square, and the gypsum board ceiling is mostly a square ceiling. The square ceiling will give people a sense of neatness and atmosphere, and the shape of the straight line is also suitable for many decoration styles.

Gypsum board ceilings should not be designed in the living room with complex shapes, and should be based on the interior decoration style. Generally, the simple modern decoration style will often use the linear shape of the ceiling, such a ceiling form is more common on both sides of the roof, generally distributed on both sides of the TV background wall and the sofa, the main light source is installed in the middle, and the ceiling is designed with downlights and light belts to create an indoor atmosphere. The four-sided linear shape of the ceiling side is also very common, and the middle part maintains the original top surface, which will make the interior space very spacious and have no sense of oppression in height.

Second, the gypsum board ceiling should consider the style issue.

How to design a gypsumboard ceiling in the living room? If the interior decoration style is European style, it will appear more complex when doing gypsum board ceiling design in the living room, and the European ceiling will be divided into several levels of ceilings, characterized by the sense of hierarchy and the edge of the ceiling decorative gypsum lines to express the European style of gorgeous and exquisite. The top of the middle will also use gypsum decorative lines, and there are many decorative techniques, so the ceiling should pay attention to the height of the house, and the living room space of the villa can express the atmosphere of European style by using such a ceiling.

Third, the gypsum board ceiling should consider the structural issues.

How to design a gypsumboard ceiling in the living room? Gypsum board living room ceiling modeling**, gypsum board ceiling in addition to the decorative effect, many times in the design of the ceiling modeling to consider structural problems, some in order to cover the beam to design the shape. If there is a ** air conditioner in the room, in order to arrange the air conditioning outlet, the functionality of its shape will be considered when designing the ceiling.

Fourth, gypsum board ceilings should consider the problem of lamps and lanterns.

How to design a gypsumboard ceiling in the living room? Gypsum board ceiling should pay attention to the arrangement of lamps and lanterns in the design, and pay attention to the importance of auxiliary light sources in addition to the main light source. The living room is generally bright, and the light of the main light source should fill the living room space.

If the living room area is large, auxiliary light sources will generally be added, and downlights, spotlights, and light strips will be used to meet the lighting needs. The use of auxiliary light sources can also play a role in creating different indoor atmospheres.

Mix white latex or polyethylene glue with gypsum powder, but now there are anti-cracking products on the market that do not need to be adjusted, but the price is relatively high. And the effect is not as good as gypsum powder, fill the gaps after adjusting evenly, and then paste gauze tape on the outside (kraft paper is better than gauze tape, there is a new type of fiberglass mesh belt), and then scrape putty.

Gypscale ceilings with porcelain.

Brick wall joints can be made with glass glue, the steps are as follows:

First of all, you need to be able to use a glue gun;

Determine the width of the genus for you to glue, that is, the width of the gap;

According to the width of the gluing gap, cut the glue nozzle into a slightly smaller diameter than the gap;

Do a good job of protecting both sides of the glue gap, and paste 2-3cm adhesive tape on the materials on both sides of the gap, which protects the materials on both sides and is also very convenient for correcting the glue in the gap;

Master the speed of gluing and the speed of the movement of the glue gun, and move the glue gun evenly according to the depth of the gap;

Trim the gluing area, find a shovel to scrape the uneven places, and repair the glue where there is no gap when gluing;

After 48 hours, remove the adhesive tape on both sides of the material to complete the construction.

With gypsum-based caulk, inorganic and environmentally friendly. The gypsum substrate shrinks less and generally does not crack.

Gypsum board ceilings and tile wall joints can be made of glass glue. First of all, you need to be able to use a glue gun; Determine the width of the glue, i.e. the width of the gap.

According to the width of the gluing gap, cut the glue nozzle into a slightly smaller diameter than the gap; Do a good job of protecting the working mode on both sides of the glue gap, and paste 2-3cm adhesive tape on the materials on both sides of the gap, which protects the materials on both sides and also has great convenience for correcting the glue in the gap.

Master the speed of gluing and the speed of the sail head of the glue gun movement, and move the glue gun evenly according to the depth of the gap; Trim the gluing area, find a shovel to scrape the uneven places, and repair the glue where there is no gap when gluing; After 48 hours, remove the adhesive tape on both sides of the material to complete the construction.