Car door disassembly steps, car door glass disassembly steps?

Front doors. 1-exterior trim strip; 2-inner handle; 3-door glass; 4-outer handle; 5-door lock; 6-lock seat; 7-interior strip (top); 8-interior strip (down); 9-inner handle cover; 10-lifter handle; 11-door hinge.

below); 12-door hinge (upper); 13-front door panel assembly; 14-glass regulator; 15-waterproof rubber strip.

Disassembly and assembly steps.

1) Prepare tools and work carts or work benches.

2) Open the door to the maximum to make it easier to operate the hinged support, place a bracket on the lower edge of the door to support the door weight and protect the door, and unscrew the window glass (below). In this example, the rear door is mainly disassembled, such as the front door to remove the exterior mirror. ▼

3) Disassemble the door and body wire connectors to separate the door wiring harness. If necessary, remove the inner trim on the column first. ▼

4) Remove the clip at the bottom of the door limiter stop lock pin and pull the lock pin out of the hole. ▼

5) Hold on to the door and remove the door hinge bearing connecting bolts. Remove the door and place it vertically on a padded surface. If you only need to remove the door for repair, it is recommended to remove the hinge connection bolts instead of the fixing bolts to remove the door, which will reduce the need for door adjustments.

6) Check the casing of the door chain, replace it if necessary, lubricate the hinges, put the door back on the hinge support, and reinstall the bolts. ▼

7) Connect the door limiter, install the stop lock pin and lock tab, and connect the wire plug. ▼

8) Close the door, check whether it is aligned, correct it if necessary, and tighten the hinge fixing bolt if there is no problem. ▼

9) Note that if the front door is disassembled, the rearview mirror needs to be installed.

Adjustment method.

When the door is installed, it must be adjusted to meet the requirements for use. Such as the door fit clearance.

It should meet the aesthetic requirements, the door and its adjacent parts should not interfere, and the door light should be turned off when the door is closed.

1) Check the gap around the door, the gap should be uniform, and the door and its adjacent parts should not interfere with the action. ▼

2) Loosen the connecting bolts of the hinged support and move the door in the required direction to make the door gap uniform and consistent. ▼

3) Loosen the fixing bolts of the door latch and adjust the position of the rear edge of the door by moving the door latch in or out of the car. ▼

Use special tools to protect the connecting bolts and door trim from damage.

Handle with care so as not to damage the paint surface.

Before removing the entire door, make sure that all the wires have been removed and connected to prevent the wires from being broken.

Strictly follow the operation steps to avoid repeated damage to the door components.

During installation, the clearance must be adjusted according to the clearance requirements, and the opening and closing of the door must be normal and smooth.

Remove the inner door handle trim first, then remove the door trim panel, remove the central lock, reversing mirror and window control switch plug, remove the wiring harness, remove the door limiter, remove the door hinge (you have to cooperate with two people, the door is very heavy), remove and remove the assembly, and the installation process is the opposite.

1. Replace the door glass

The door glass is actually very easy to replace, the main job is to disassemble the door trim panel, especially pay attention not to damage the door trim panel, the specific method is as follows:

First, find and remove the hidden bolts;

2.Take off the buckle and boldly disassemble the door trim panels;

3.Adjust the windows, remove the glass fixing bolts, and remove the glass.

2. Replace the sunroof glass.

When replacing the sunroof glass, remove it together with the sealing rubber ring when dismantling, and generally only the assembly can be purchased when purchasing glass, so you can install it according to the reverse steps of disassembly.

Some people think that the roof should be dismantled, and the motor should be dismantled, etc., which can not be destroyed without seepage, if the motor is really broken, then it is possible to quietly dismantle the roof and sunroof skeleton.

3. Replace the rearview mirror.

The rearview mirror replacement steps are also very simple, general accessories stores, not only sell lenses, only sell rearview mirror assembly. Open the door and remove the door trim panels, and some cars can replace the mirrors without dismantling them. When buying a rearview mirror assembly, pay attention to the fact that there are electric and manual, although the shape is the same, it is still necessary to choose carefully.

Fourth, replace the triangular glass.

Some triangular window panes are glued like a windshield.

Bonded, some are fixed by screws and screws, this type of model first has to find the position of the screws and screws, a cluster of transport can be seen under the sealing strip, bolts are installed under the interior panel.

The first step is to open the door trim, remove the fixing screws of the glass lift and the glass, and finally remove the glass.

Hello friends.

1.One. Replacing Door Glass: Door glass is actually very easy to replace, and the main job is to remove the door trim panel ,..

2.First, find and remove the hidden bolts;

3. Disconnect the buckle and boldly disassemble the door trim panel;

4. Adjust the windows, remove the glass fixing bolts, and take out the glass.

5.Two. Replace the sunroof glass When replacing the sunroof glass, remove it together with the sealing rubber ring when dismantling, and generally only the assembly can be purchased when buying glass, so you can install it according to the reverse steps of disassembly.

1.Prepare tools and work carts or work benches.

2.Open the door to the maximum to make it easier to operate the articulated mount, place a bracket on the lower edge of the door to support the weight of the door and protect the door, and unscrew the window glass. In this example, the rear door is disassembled and assembled.

3.Disassemble the door from the body wire connector to separate the door harness. If necessary, remove the inner trim on the column first. ▼

4.Remove the clip from the bottom of the door limiter stop pin and remove the pin from the hole. ▼5.Hold on to the door and remove the door hinge support connecting bolts. Remove the door and place it vertically on a padded surface.