How to install a fan? How to install an electric fan?

Ordinary floor fan installation method:

1. Assemble the foot plate and the column tube first, and fix them with screws or butterfly screws and other objects.

2. Then assemble and fix the fuselage part of the whole machine and the column tube.

3. Fix the rear mesh of the fan on the front shell of the motor using a mesh harness.

4. Use the fan blade lock nut to fix the fan blade on the motor shaft.

5. Use a mesh ring for the front and back nets or screw the front mesh into the back net, and then fix it with screws.

A fan is assembled.

Electric fan installation method:

Tool materials required: electric fan, screwdriver.

1. Disassemble the express and place the parts neatly.

2. Start the installation and install it from the base network.

3. Install the machine head.

4. Install the fan blades, pay attention to remove the two fixing buckles first.

5. Install the back cover, fan blade, and front cover.

6. When installing the fan blade, pay attention to the clamping of the fan blade groove and the rotating rod.

7. Install the fixed clamp.

8. Turn on the power supply and check whether the wind level, shaking head and other functions are normal.

How to choose an electric fan

1。Look at the random documents The random documents of each electric fan include the instruction manual, product certificate, electrical circuit diagram and packing list, and the quantity and quality of parts should be checked and checked according to the packing list when purchasing.

2.See whether the grille and fan blades are obviously deformed: on the assembled electric fan grille, use a pen to point to the highest point of a fan blade, slowly move the fan blade, and the distance between the corresponding points of the other fan blades and the pen tip should be very close, and then rotate the fan blade, pay attention to observe whether the rotation is light and flexible, and can stop at any position.

3.See whether the control mechanism is flexible: the control mechanism includes speed control switches, timing knobs, shaking head switches, light switches, etc., and these control mechanisms should operate flexibly and contact reliably.

For the speed control gear, it is not allowed to have two gears turned on at the same time or one gear cannot be pressed. Press the stop button, and each speed stop button should be reset normally.

4.Look at the performance of the active part: the electric fan head runs flexibly at all angles of pitch and tilt, locks firmly, adjusts to the maximum depression angle or shakes the head to the final position, and the grille must not touch the fan pillar.

When the fan is running, the stability should be good, it should not be tipped over, and the shaking angle should not be lower than 60-80 degrees.

Tool materials required: electric fan, screwdriver.

1. Disassemble the express and place the parts neatly.

2. Start the installation and install it from the base network.

3. Install the machine head.

4. Install the fan blades, pay attention to remove the two fixing buckles first.

5. Install the back cover, fan blade, and front cover.

6. When installing the fan blade, pay attention to the clamping of the fan blade groove and the rotating rod.

7. Install the fixed clamp.

8. Turn on the power supply and check whether the wind level, shaking head and other functions are normal.

Is that all there is to it?

The two positions are linked, and the screws are tightened.

Ask questions and everything else, that's all.

2. Take out the lifting rod from the base pipe and tighten the middle to fix it, and the base installation is completed (note: part of the fan lifting rod is inside the column).

3. After the mounting hole of the main head is inserted into the round tube and stuck in the groove, tighten the fixing screw with a screwdriver.

4. Load the rear grille into the main head, and then tighten it with the mesh cover cable.

5. Put the fan blade into the motor shaft, and tighten it with the fan blade cable mother after it is in place (note: the fan blade cable mother is loosened in the clockwise direction, don't screw it in the wrong direction, otherwise it will burst).

6. Put the mesh ring into the rear grille, then put the front grille, and tighten the screws in the ring with a screwdriver.

I can't see that screw of yours, I can't see it clearly.

This kind of installation is similar to this. It's about aligning that hole, which can be moved up and down, and then installing the screws.

Question, yes, but he doesn't have the kind of position that can be fixed up and down like the original. Now I'm removing it and reinstalling it, and then he can't swing it up and down. Also, I'm running out of information, see if you can help me, if you can't help, forget it, thank you.

Here's how to install a computer fan:Tools: Lenovo PC Tianyi 510S, Windows fan, silicone.

1. First of all, apply a layer of silicone to the middle of the fan.

2. Then we put the four feet of the fan, corresponding to the four card slots on the motherboard, and the power supply line of the fan, preferably towards the slot (the right side of Figure 1), so as to prevent the line from being wound by the fan.

3. Finally, press the four feet into the card slot, hear the sound of 'click', and finally rotate the handle of the fan in one direction (better fix the fan), install the power supply line, and the computer fan will be installed.

<>1. First of all, check whether the parts in Figure 1 below are two pieces, and the white POM parts can be removed. Let's take these two apart first.

2. Place the position of the part of Figure 2 in Figure 4, and the notch position of the part in Figure 2 is aligned with the screw position of Figure 4.

3. Attach the page of Figure 3.

4. After disassembling the white parts in Figure 1, there should be a lock screw hole on the surface of the white parts, use screws to fix the white parts in Figure 1 at the position of Figure 5, and then snap the orange parts on.

Remove the two screws from the fan in Figure 1 and attach the white parts in Figure 2! Notch align the screw mouth, and then add the screw!

Next, install the fan blades!

Finally, install the fan blade cap and you're done!!

Where did you buy it? Ask customer service.

This can be directly put on the buckle of the radiator, and the round one is not used.

It depends on which platform your motherboard is, I remember that the motherboard of different platforms corresponds to different installation methods, anyway, it is not difficult, the heatsink you bought should have a tutorial, it really doesn't work you ask the merchant.

The cooling fan in the computer has an impeller collar cover on the front, the blades are facing downward, and the impeller bearing supports the skeleton on the reverse side. There is a fan specification label on it, and the impeller bearing chamber is torn off.

CPU cooler is specifically designed to provide heat dissipation needs for the CPU, so the importance can be imagined, CPU cooler installation is not difficult, especially the down-blowing radiator, but for the tower side-blown CPU cooler, the fan orientation needs to be installed correctly to better heat dissipation.

Proper use of cooling fans.

The correct use of the cooling fan can not only improve the efficiency but also prolong the service life, so we need to pay attention to the cooling fan to operate in a suitable temperature environment, pay attention to the choice of bearing is oil-containing or double-ball, the service life of the ball will be as long as two-thirds than the oil-containing one, and the voltage of the cooling fan can not exceed the rated voltage of the fan.

Usually pay more attention to the maintenance of the cooling fan, maintain the cooling fan, clean it, then the life will be extended. The above is a brief introduction to the correct use of cooling fans, although most of the cooling fans are used in the equipment, but the fan is also a very important accessory, which can improve the efficiency of the equipment.